linux-kernel - [PATCH v2 1/2] ARM: dts: sun8i: h3: Enable AP6212 WiFi on mmc1 on Nanopi M1 Plus

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <1504283401-4263-2-git-send-email-embed3d@gmail.com>
Date:   Fri,  1 Sep 2017 18:30:00 +0200
From:   Philipp Rossak <embed3d@...il.com>
To:     robh+dt@...nel.org, mark.rutland@....com, linux@...linux.org.uk,
        maxime.ripard@...e-electrons.com, wens@...e.org
Cc:     Philipp Rossak <embed3d@...il.com>, devicetree@...r.kernel.org,
        linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
        linux-sunxi@...glegroups.com
Subject: [PATCH v2 1/2] ARM: dts: sun8i: h3: Enable AP6212 WiFi on mmc1 on Nanopi M1 Plus

From: Philipp Rossak <embed3d@...il.com>

The WiFi side of the AP6212 WiFi/BT combo module is connected to
mmc1. There are also GPIOs for enable and interrupts.

Enable WiFi on this board by enabling mmc1 and adding the power
sequencing clocks and GPIO, as well as the chip's interrupt line.

Signed-off-by: Philipp Rossak <embed3d@...il.com>
---
 arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
index 6256f55..7d18c35 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
@@ -48,6 +48,13 @@
 
 	aliases {
 		serial1 = &uart3;
+		ethernet1 = &sdio_wifi;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
 	};
 };
 
@@ -65,6 +72,24 @@
 	status = "okay";
 };
 
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	sdio_wifi: sdio_wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
+
 &ohci1 {
 	status = "okay";
 };
-- 
2.7.4