| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20171101040457.1200-2-andrew@aj.id.au>
Date: Wed, 1 Nov 2017 15:04:56 +1100
From: Andrew Jeffery <andrew@...id.au>
To: linux-gpio@...r.kernel.org
Cc: Andrew Jeffery <andrew@...id.au>, linus.walleij@...aro.org,
robh+dt@...nel.org, mark.rutland@....com, frowand.list@...il.com,
joel@....id.au, ckeepax@...nsource.wolfsonmicro.com,
ldewangan@...dia.com, ryan_chen@...eedtech.com,
linux-kernel@...r.kernel.org, devicetree@...r.kernel.org,
openbmc@...ts.ozlabs.org, linux-aspeed@...ts.ozlabs.org
Subject: [PATCH v3 1/2] gpio: gpiolib: Generalise state persistence beyond sleep
General support for state persistence is added to gpiolib with the
introduction of a new pinconf parameter to propagate the request to
hardware. The existing persistence support for sleep is adapted to
include hardware support if the GPIO driver provides it. Persistence
continues to be enabled by default; in-kernel consumers can opt out, but
userspace (currently) does not have a choice.
The *_SLEEP_MAY_LOSE_VALUE and *_SLEEP_MAINTAIN_VALUE symbols are
renamed, dropping the SLEEP prefix to reflect that the concept is no
longer sleep-specific. I feel that renaming to just *_MAY_LOSE_VALUE
could initially be misinterpreted, so I've further changed the symbols
to *_TRANSITORY and *_PERSISTENT to address this.
The sysfs interface is modified only to keep consistency with the
chardev interface in enforcing persistence for userspace exports.
Signed-off-by: Andrew Jeffery <andrew@...id.au>
---
drivers/gpio/gpiolib-of.c | 6 ++--
drivers/gpio/gpiolib-sysfs.c | 14 +++++---
drivers/gpio/gpiolib.c | 61 ++++++++++++++++++++++++++++++---
drivers/gpio/gpiolib.h | 2 +-
include/dt-bindings/gpio/gpio.h | 6 ++--
include/linux/gpio/consumer.h | 8 +++++
include/linux/gpio/machine.h | 4 +--
include/linux/of_gpio.h | 2 +-
include/linux/pinctrl/pinconf-generic.h | 2 ++
9 files changed, 87 insertions(+), 18 deletions(-)
diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index e0d59e61b52f..4a2b8d3397c7 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -153,8 +153,8 @@ struct gpio_desc *of_find_gpio(struct device *dev, const char *con_id,
*flags |= GPIO_OPEN_SOURCE;
}
- if (of_flags & OF_GPIO_SLEEP_MAY_LOSE_VALUE)
- *flags |= GPIO_SLEEP_MAY_LOSE_VALUE;
+ if (of_flags & OF_GPIO_TRANSITORY)
+ *flags |= GPIO_TRANSITORY;
return desc;
}
@@ -214,6 +214,8 @@ static struct gpio_desc *of_parse_own_gpio(struct device_node *np,
if (xlate_flags & OF_GPIO_ACTIVE_LOW)
*lflags |= GPIO_ACTIVE_LOW;
+ if (xlate_flags & OF_GPIO_TRANSITORY)
+ *lflags |= GPIO_TRANSITORY;
if (of_property_read_bool(np, "input"))
*dflags |= GPIOD_IN;
diff --git a/drivers/gpio/gpiolib-sysfs.c b/drivers/gpio/gpiolib-sysfs.c
index 3f454eaf2101..0bd472ffb072 100644
--- a/drivers/gpio/gpiolib-sysfs.c
+++ b/drivers/gpio/gpiolib-sysfs.c
@@ -474,11 +474,15 @@ static ssize_t export_store(struct class *class,
status = -ENODEV;
goto done;
}
- status = gpiod_export(desc, true);
- if (status < 0)
- gpiod_free(desc);
- else
- set_bit(FLAG_SYSFS, &desc->flags);
+
+ status = gpiod_set_transitory(desc, false);
+ if (!status) {
+ status = gpiod_export(desc, true);
+ if (status < 0)
+ gpiod_free(desc);
+ else
+ set_bit(FLAG_SYSFS, &desc->flags);
+ }
done:
if (status)
diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index 3827f0767101..a5e81dc03aba 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -503,6 +503,10 @@ static int linehandle_create(struct gpio_device *gdev, void __user *ip)
if (lflags & GPIOHANDLE_REQUEST_OPEN_SOURCE)
set_bit(FLAG_OPEN_SOURCE, &desc->flags);
+ ret = gpiod_set_transitory(desc, false);
+ if (ret < 0)
+ goto out_free_descs;
+
/*
* Lines have to be requested explicitly for input
* or output, else the line will be treated "as is".
@@ -2424,6 +2428,49 @@ int gpiod_set_debounce(struct gpio_desc *desc, unsigned debounce)
EXPORT_SYMBOL_GPL(gpiod_set_debounce);
/**
+ * gpiod_set_transitory - Lose or retain GPIO state on suspend or reset
+ * @desc: descriptor of the GPIO for which to configure persistence
+ * @transitory: True to lose state on suspend or reset, false for persistence
+ *
+ * Returns:
+ * 0 on success, otherwise a negative error code.
+ */
+int gpiod_set_transitory(struct gpio_desc *desc, bool transitory)
+{
+ struct gpio_chip *chip;
+ unsigned long packed;
+ int gpio;
+ int rc;
+
+ /*
+ * Handle FLAG_TRANSITORY first, enabling queries to gpiolib for
+ * persistence state.
+ */
+ if (transitory)
+ set_bit(FLAG_TRANSITORY, &desc->flags);
+ else
+ clear_bit(FLAG_TRANSITORY, &desc->flags);
+
+ /* If the driver supports it, set the persistence state now */
+ chip = desc->gdev->chip;
+ if (!chip->set_config)
+ return 0;
+
+ packed = pinconf_to_config_packed(PIN_CONFIG_PERSIST_STATE,
+ !transitory);
+ gpio = gpio_chip_hwgpio(desc);
+ rc = chip->set_config(chip, gpio, packed);
+ if (rc == -ENOTSUPP) {
+ dev_dbg(&desc->gdev->dev, "Persistence not supported for GPIO %d\n",
+ gpio);
+ return 0;
+ }
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(gpiod_set_transitory);
+
+/**
* gpiod_is_active_low - test whether a GPIO is active-low or not
* @desc: the gpio descriptor to test
*
@@ -3010,8 +3057,7 @@ bool gpiochip_line_is_persistent(struct gpio_chip *chip, unsigned int offset)
if (offset >= chip->ngpio)
return false;
- return !test_bit(FLAG_SLEEP_MAY_LOSE_VALUE,
- &chip->gpiodev->descs[offset].flags);
+ return !test_bit(FLAG_TRANSITORY, &chip->gpiodev->descs[offset].flags);
}
EXPORT_SYMBOL_GPL(gpiochip_line_is_persistent);
@@ -3435,8 +3481,10 @@ int gpiod_configure_flags(struct gpio_desc *desc, const char *con_id,
set_bit(FLAG_OPEN_DRAIN, &desc->flags);
if (lflags & GPIO_OPEN_SOURCE)
set_bit(FLAG_OPEN_SOURCE, &desc->flags);
- if (lflags & GPIO_SLEEP_MAY_LOSE_VALUE)
- set_bit(FLAG_SLEEP_MAY_LOSE_VALUE, &desc->flags);
+
+ status = gpiod_set_transitory(desc, (lflags & GPIO_TRANSITORY));
+ if (status < 0)
+ return status;
/* No particular flag request, return here... */
if (!(dflags & GPIOD_FLAGS_BIT_DIR_SET)) {
@@ -3550,6 +3598,7 @@ struct gpio_desc *fwnode_get_named_gpiod(struct fwnode_handle *fwnode,
bool active_low = false;
bool single_ended = false;
bool open_drain = false;
+ bool transitory = false;
int ret;
if (!fwnode)
@@ -3564,6 +3613,7 @@ struct gpio_desc *fwnode_get_named_gpiod(struct fwnode_handle *fwnode,
active_low = flags & OF_GPIO_ACTIVE_LOW;
single_ended = flags & OF_GPIO_SINGLE_ENDED;
open_drain = flags & OF_GPIO_OPEN_DRAIN;
+ transitory = flags & OF_GPIO_TRANSITORY;
}
} else if (is_acpi_node(fwnode)) {
struct acpi_gpio_info info;
@@ -3594,6 +3644,9 @@ struct gpio_desc *fwnode_get_named_gpiod(struct fwnode_handle *fwnode,
lflags |= GPIO_OPEN_SOURCE;
}
+ if (transitory)
+ lflags |= GPIO_TRANSITORY;
+
ret = gpiod_configure_flags(desc, propname, lflags, dflags);
if (ret < 0) {
gpiod_put(desc);
diff --git a/drivers/gpio/gpiolib.h b/drivers/gpio/gpiolib.h
index af48322839c3..736b189d1bb5 100644
--- a/drivers/gpio/gpiolib.h
+++ b/drivers/gpio/gpiolib.h
@@ -205,7 +205,7 @@ struct gpio_desc {
#define FLAG_OPEN_SOURCE 8 /* Gpio is open source type */
#define FLAG_USED_AS_IRQ 9 /* GPIO is connected to an IRQ */
#define FLAG_IS_HOGGED 11 /* GPIO is hogged */
-#define FLAG_SLEEP_MAY_LOSE_VALUE 12 /* GPIO may lose value in sleep */
+#define FLAG_TRANSITORY 12 /* GPIO may lose value in sleep or reset */
/* Connection label */
const char *label;
diff --git a/include/dt-bindings/gpio/gpio.h b/include/dt-bindings/gpio/gpio.h
index 70de5b7a6c9b..43dc230d3921 100644
--- a/include/dt-bindings/gpio/gpio.h
+++ b/include/dt-bindings/gpio/gpio.h
@@ -28,8 +28,8 @@
#define GPIO_OPEN_DRAIN (GPIO_SINGLE_ENDED | GPIO_LINE_OPEN_DRAIN)
#define GPIO_OPEN_SOURCE (GPIO_SINGLE_ENDED | GPIO_LINE_OPEN_SOURCE)
-/* Bit 3 express GPIO suspend/resume persistence */
-#define GPIO_SLEEP_MAINTAIN_VALUE 0
-#define GPIO_SLEEP_MAY_LOSE_VALUE 8
+/* Bit 3 express GPIO suspend/resume and reset persistence */
+#define GPIO_PERSISTENT 0
+#define GPIO_TRANSITORY 8
#endif
diff --git a/include/linux/gpio/consumer.h b/include/linux/gpio/consumer.h
index d4920ec1f1da..d77e88c96f38 100644
--- a/include/linux/gpio/consumer.h
+++ b/include/linux/gpio/consumer.h
@@ -132,6 +132,7 @@ void gpiod_set_raw_array_value_cansleep(unsigned int array_size,
int *value_array);
int gpiod_set_debounce(struct gpio_desc *desc, unsigned debounce);
+int gpiod_set_transitory(struct gpio_desc *desc, bool transitory);
int gpiod_is_active_low(const struct gpio_desc *desc);
int gpiod_cansleep(const struct gpio_desc *desc);
@@ -424,6 +425,13 @@ static inline int gpiod_set_debounce(struct gpio_desc *desc, unsigned debounce)
return -ENOSYS;
}
+static inline int gpiod_set_transitory(struct gpio_desc *desc, bool transitory)
+{
+ /* GPIO can never have been requested */
+ WARN_ON(1);
+ return -ENOSYS;
+}
+
static inline int gpiod_is_active_low(const struct gpio_desc *desc)
{
/* GPIO can never have been requested */
diff --git a/include/linux/gpio/machine.h b/include/linux/gpio/machine.h
index 5e9f294c29eb..33a97ede6404 100644
--- a/include/linux/gpio/machine.h
+++ b/include/linux/gpio/machine.h
@@ -9,8 +9,8 @@ enum gpio_lookup_flags {
GPIO_ACTIVE_LOW = (1 << 0),
GPIO_OPEN_DRAIN = (1 << 1),
GPIO_OPEN_SOURCE = (1 << 2),
- GPIO_SLEEP_MAINTAIN_VALUE = (0 << 3),
- GPIO_SLEEP_MAY_LOSE_VALUE = (1 << 3),
+ GPIO_PERSISTENT = (0 << 3),
+ GPIO_TRANSITORY = (1 << 3),
};
/**
diff --git a/include/linux/of_gpio.h b/include/linux/of_gpio.h
index 1fe205582111..18a7f03e1182 100644
--- a/include/linux/of_gpio.h
+++ b/include/linux/of_gpio.h
@@ -31,7 +31,7 @@ enum of_gpio_flags {
OF_GPIO_ACTIVE_LOW = 0x1,
OF_GPIO_SINGLE_ENDED = 0x2,
OF_GPIO_OPEN_DRAIN = 0x4,
- OF_GPIO_SLEEP_MAY_LOSE_VALUE = 0x8,
+ OF_GPIO_TRANSITORY = 0x8,
};
#ifdef CONFIG_OF_GPIO
diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index 5d8bc7f21c2a..824094f39ad2 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -90,6 +90,7 @@
* @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
* this parameter (on a custom format) tells the driver which alternative
* slew rate to use.
+ * @PIN_CONFIG_PERSIST_STATE: retain pin state across sleep or controller reset
* @PIN_CONFIG_END: this is the last enumerator for pin configurations, if
* you need to pass in custom configurations to the pin controller, use
* PIN_CONFIG_END+1 as the base offset.
@@ -117,6 +118,7 @@ enum pin_config_param {
PIN_CONFIG_POWER_SOURCE,
PIN_CONFIG_SLEEP_HARDWARE_STATE,
PIN_CONFIG_SLEW_RATE,
+ PIN_CONFIG_PERSIST_STATE,
PIN_CONFIG_END = 0x7F,
PIN_CONFIG_MAX = 0xFF,
};
--
2.11.0
Powered by blists - more mailing lists