| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1512379270-27436-6-git-send-email-narmstrong@baylibre.com>
Date: Mon, 4 Dec 2017 10:21:09 +0100
From: Neil Armstrong <narmstrong@...libre.com>
To: shawnguo@...nel.org, kernel@...gutronix.de, fabio.estevam@....com
Cc: Neil Armstrong <narmstrong@...libre.com>,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: [RESEND PATCH v5 5/6] ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support
This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
SoM Carrier-Board.
This Carrier-Board has the following :
- LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
- HDMI Connector
- USB Host + USB OTG Connector
- 10/100/1000 Mbps Ethernet
- miniPCI-Express slot
- SD Card connector
- Audio Headphone/Line In jack connectors
- On-board DMIC
- CAN bus header
- SPI header
- Camera Interfaces header
- 4xButtons, 2xLeds
- OnBoard RTC with Coin Backup battery socket
- RS232 Header + USB-Serial debug port
Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits
The board support is done with all on-board and header interfaces enabled.
7" LVDS Touchscreen is enabled by default along HDMI output.
Audio interface is supported with the "simple-card" bindings.
PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
Reviewed-by: Fabio Estevam <fabio.estevam@....com>
Signed-off-by: Neil Armstrong <narmstrong@...libre.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-var-dt6customboard.dts | 235 +++++++++++++++++++++++++
2 files changed, 236 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-var-dt6customboard.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d0381e9..148ff15 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -470,6 +470,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-tx6q-11x0-mb7.dtb \
imx6q-udoo.dtb \
imx6q-utilite-pro.dtb \
+ imx6q-var-dt6customboard.dtb \
imx6q-wandboard.dtb \
imx6q-wandboard-revb1.dtb \
imx6q-wandboard-revd1.dtb \
diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
new file mode 100644
index 0000000..e0728d4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
@@ -0,0 +1,235 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Support for Variscite DART-MX6 Carrier-board
+ *
+ * Copyright 2017 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@...libre.com>
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-var-dart.dtsi"
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+ model = "Variscite DART-MX6 Carrier-board";
+ compatible = "variscite,dt6customboard", "fsl,imx6q";
+
+ backlight_lvds: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 50000>;
+ brightness-levels = <0 4 8 16 32 64 128 248>;
+ default-brightness-level = <7>;
+ status = "okay";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ back {
+ gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_BACK>;
+ label = "Key Back";
+ linux,input-type = <1>;
+ debounce-interval = <100>;
+ wakeup-source;
+ };
+
+ home {
+ gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOME>;
+ label = "Key Home";
+ linux,input-type = <1>;
+ debounce-interval = <100>;
+ wakeup-source;
+ };
+
+ menu {
+ gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_MENU>;
+ label = "Key Menu";
+ linux,input-type = <1>;
+ debounce-interval = <100>;
+ wakeup-source;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led1 {
+ gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led2 {
+ gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ panel1: lvds-panel {
+ compatible = "sgd,gktw70sdae4se", "panel-lvds";
+ backlight = <&backlight_lvds>;
+ width-mm = <153>;
+ height-mm = <86>;
+ label = "gktw70sdae4se";
+ data-mapping = "jeida-18";
+
+ panel-timing {
+ clock-frequency = <32000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <39>;
+ hfront-porch = <39>;
+ vback-porch = <29>;
+ vfront-porch = <13>;
+ hsync-len = <47>;
+ vsync-len = <2>;
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds1_out>;
+ };
+ };
+ };
+
+ reg_usb_h1_vbus: regulator-usbh1vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_otg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "dt6-customboard-audio";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&sound_codec>;
+ simple-audio-card,frame-master = <&sound_codec>;
+ simple-audio-card,widgets = "Headphone", "Headphone Jack",
+ "Line", "Line In";
+ simple-audio-card,routing = "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In";
+
+ sound_cpu: simple-audio-card,cpu {
+ sound-dai = <&ssi2>;
+ };
+
+ sound_codec: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3106>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ };
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>,
+ <&gpio4 10 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&fec {
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ status = "okay";
+
+ touchscreen@38 {
+ compatible = "edt,edt-ft5x06";
+ reg = <0x38>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+ touchscreen-size-x = <800>;
+ touchscreen-size-y = <480>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ };
+
+ rtc@68 {
+ compatible = "isil,isl12057";
+ reg = <0x68>;
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@1 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds1_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ dr_mode = "otg";
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ status = "okay";
+};
+
+&usdhc2 {
+ cd-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
--
2.7.4
Powered by blists - more mailing lists