Message-ID: <20180117234141.21184.44067.stgit@tlendack-t1.amdoffice.net>
Date:   Wed, 17 Jan 2018 17:41:41 -0600
From:   Tom Lendacky <thomas.lendacky@....com>
To:     x86@...nel.org, linux-kernel@...r.kernel.org
Cc:     Juergen Gross <jgross@...e.com>, Tony Luck <tony.luck@...el.com>,
        Arjan van de Ven <arjan@...ux.intel.com>,
        Yu Chen <yu.c.chen@...el.com>, Baoquan He <bhe@...hat.com>,
        Linus Torvalds <torvalds@...ux-foundation.org>,
        Ingo Molnar <mingo@...nel.org>, kexec@...ts.infradead.org,
        Rui Zhang <rui.zhang@...el.com>, ebiederm@...hat.com,
        Borislav Petkov <bp@...en8.de>,
        "H. Peter Anvin" <hpa@...or.com>,
        Thomas Gleixner <tglx@...utronix.de>,
        Dave Young <dyoung@...hat.com>,
        Boris Ostrovsky <boris.ostrovsky@...cle.com>,
        Dan Williams <dan.j.williams@...el.com>
Subject: [PATCH] x86/mm: Rework wbinvd, hlt operation in stop_this_cpu()

Some issues have been reported with the for loop in stop_this_cpu() that
issues the 'wbinvd; hlt' sequence.  Reverting this sequence to halt()
has been shown to resolve the issue.

However, the wbinvd is needed when running with SME.  The reason for the
wbinvd is to prevent cache flush races between encrypted and non-encrypted
entries that have the same physical address.  This can occur when
kexec'ing from memory encryption active to inactive or vice-versa.  The
important thing is to not have outside of kernel text memory references
(such as stack usage), so the usage of the native_*() functions is needed
since these expand as inline asm sequences.  So instead of reverting the
change, rework the sequence.

Move the wbinvd instruction outside of the for loop as native_wbinvd()
and make its execution conditional on X86_FEATURE_SME.  In the for loop,
change the asm 'wbinvd; hlt' sequence back to a halt sequence but use
the native_halt() call.

Cc: <stable@...r.kernel.org> # 4.14.x
Fixes: bba4ed011a52 ("x86/mm, kexec: Allow kexec to be used with SME")
Reported-by: Dave Young <dyoung@...hat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@....com>
---
 arch/x86/kernel/process.c |   25 +++++++++++++++----------
 1 file changed, 15 insertions(+), 10 deletions(-)

diff --git a/arch/x86/kernel/process.c b/arch/x86/kernel/process.c
index 63711fe..03408b9 100644
--- a/arch/x86/kernel/process.c
+++ b/arch/x86/kernel/process.c
@@ -379,19 +379,24 @@ void stop_this_cpu(void *dummy)
 	disable_local_APIC();
 	mcheck_cpu_clear(this_cpu_ptr(&cpu_info));
 
+	/*
+	 * Use wbinvd on processors that support SME. This provides support
+	 * for performing a successful kexec when going from SME inactive
+	 * to SME active (or vice-versa). The cache must be cleared so that
+	 * if there are entries with the same physical address, both with and
+	 * without the encryption bit, they don't race each other when flushed
+	 * and potentially end up with the wrong entry being committed to
+	 * memory.
+	 */
+	if (boot_cpu_has(X86_FEATURE_SME))
+		native_wbinvd();
 	for (;;) {
 		/*
-		 * Use wbinvd followed by hlt to stop the processor. This
-		 * provides support for kexec on a processor that supports
-		 * SME. With kexec, going from SME inactive to SME active
-		 * requires clearing cache entries so that addresses without
-		 * the encryption bit set don't corrupt the same physical
-		 * address that has the encryption bit set when caches are
-		 * flushed. To achieve this a wbinvd is performed followed by
-		 * a hlt. Even if the processor is not in the kexec/SME
-		 * scenario this only adds a wbinvd to a halting processor.
+		 * Use native_halt() so that memory contents don't change
+		 * (stack usage and variables) after possibly issuing the
+		 * native_wbinvd() above.
 		 */
-		asm volatile("wbinvd; hlt" : : : "memory");
+		native_halt();
 	}
 }
 

Powered by blists - more mailing lists