| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAFqH_52S-Om5USpnXP7_DHOhdcSLSe2KzuFaAaSxafc+CX_mww@mail.gmail.com>
Date: Wed, 23 May 2018 10:50:48 +0200
From: Enric Balletbo Serra <eballetbo@...il.com>
To: Lin Huang <hl@...k-chips.com>
Cc: Sean Paul <seanpaul@...omium.org>, David Airlie <airlied@...ux.ie>,
Chris Zhong <zyw@...k-chips.com>,
Kishon Vijay Abraham I <kishon@...com>,
Doug Anderson <dianders@...omium.org>,
Brian Norris <briannorris@...omium.org>,
"open list:ARM/Rockchip SoC..." <linux-rockchip@...ts.infradead.org>,
Heiko Stübner <heiko@...ech.de>,
daniel.vetter@...el.com,
dri-devel <dri-devel@...ts.freedesktop.org>,
Linux ARM <linux-arm-kernel@...ts.infradead.org>,
linux-kernel <linux-kernel@...r.kernel.org>,
Rob Herring <robh+dt@...nel.org>,
"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>
Subject: Re: [PATCH v7 5/5] drm/rockchip: support dp training outside dp firmware
2018-05-23 9:42 GMT+02:00 Lin Huang <hl@...k-chips.com>:
> DP firmware uses fixed phy config values to do training, but some
> boards need to adjust these values to fit for their unique hardware
> design. So get phy config values from dts and use software link training
> instead of relying on firmware, if software training fail, keep firmware
> training as a fallback if sw training fails.
>
> Signed-off-by: Chris Zhong <zyw@...k-chips.com>
> Signed-off-by: Lin Huang <hl@...k-chips.com>
> Reviewed-by: Sean Paul <seanpaul@...omium.org>
> ---
> Changes in v2:
> - update patch following Enric suggest
> Changes in v3:
> - use variable fw_training instead sw_training_success
> - base on DP SPCE, if training fail use lower link rate to retry training
> Changes in v4:
> - improve cdn_dp_get_lower_link_rate() and cdn_dp_software_train_link() follow Sean suggest
> Changes in v5:
> - fix some whitespcae issue
> Changes in v6:
> - None
> Changes in v7:
> - None
>
> drivers/gpu/drm/rockchip/Makefile | 3 +-
> drivers/gpu/drm/rockchip/cdn-dp-core.c | 24 +-
> drivers/gpu/drm/rockchip/cdn-dp-core.h | 2 +
> drivers/gpu/drm/rockchip/cdn-dp-link-training.c | 420 ++++++++++++++++++++++++
> drivers/gpu/drm/rockchip/cdn-dp-reg.c | 31 +-
> drivers/gpu/drm/rockchip/cdn-dp-reg.h | 38 ++-
> 6 files changed, 505 insertions(+), 13 deletions(-)
> create mode 100644 drivers/gpu/drm/rockchip/cdn-dp-link-training.c
>
> diff --git a/drivers/gpu/drm/rockchip/Makefile b/drivers/gpu/drm/rockchip/Makefile
> index a314e21..b932f62 100644
> --- a/drivers/gpu/drm/rockchip/Makefile
> +++ b/drivers/gpu/drm/rockchip/Makefile
> @@ -9,7 +9,8 @@ rockchipdrm-y := rockchip_drm_drv.o rockchip_drm_fb.o \
> rockchipdrm-$(CONFIG_DRM_FBDEV_EMULATION) += rockchip_drm_fbdev.o
>
> rockchipdrm-$(CONFIG_ROCKCHIP_ANALOGIX_DP) += analogix_dp-rockchip.o
> -rockchipdrm-$(CONFIG_ROCKCHIP_CDN_DP) += cdn-dp-core.o cdn-dp-reg.o
> +rockchipdrm-$(CONFIG_ROCKCHIP_CDN_DP) += cdn-dp-core.o cdn-dp-reg.o \
> + cdn-dp-link-training.o
> rockchipdrm-$(CONFIG_ROCKCHIP_DW_HDMI) += dw_hdmi-rockchip.o
> rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw-mipi-dsi.o
> rockchipdrm-$(CONFIG_ROCKCHIP_INNO_HDMI) += inno_hdmi.o
> diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.c b/drivers/gpu/drm/rockchip/cdn-dp-core.c
> index cce64c1..783d57a 100644
> --- a/drivers/gpu/drm/rockchip/cdn-dp-core.c
> +++ b/drivers/gpu/drm/rockchip/cdn-dp-core.c
> @@ -629,11 +629,13 @@ static void cdn_dp_encoder_enable(struct drm_encoder *encoder)
> goto out;
> }
> }
> -
> - ret = cdn_dp_set_video_status(dp, CONTROL_VIDEO_IDLE);
> - if (ret) {
> - DRM_DEV_ERROR(dp->dev, "Failed to idle video %d\n", ret);
> - goto out;
> + if (dp->use_fw_training) {
> + ret = cdn_dp_set_video_status(dp, CONTROL_VIDEO_IDLE);
> + if (ret) {
> + DRM_DEV_ERROR(dp->dev,
> + "Failed to idle video %d\n", ret);
> + goto out;
> + }
> }
>
> ret = cdn_dp_config_video(dp);
> @@ -642,11 +644,15 @@ static void cdn_dp_encoder_enable(struct drm_encoder *encoder)
> goto out;
> }
>
> - ret = cdn_dp_set_video_status(dp, CONTROL_VIDEO_VALID);
> - if (ret) {
> - DRM_DEV_ERROR(dp->dev, "Failed to valid video %d\n", ret);
> - goto out;
> + if (dp->use_fw_training) {
> + ret = cdn_dp_set_video_status(dp, CONTROL_VIDEO_VALID);
> + if (ret) {
> + DRM_DEV_ERROR(dp->dev,
> + "Failed to valid video %d\n", ret);
> + goto out;
> + }
> }
> +
> out:
> mutex_unlock(&dp->lock);
> }
> diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.h b/drivers/gpu/drm/rockchip/cdn-dp-core.h
> index 46159b2..77a9793 100644
> --- a/drivers/gpu/drm/rockchip/cdn-dp-core.h
> +++ b/drivers/gpu/drm/rockchip/cdn-dp-core.h
> @@ -84,6 +84,7 @@ struct cdn_dp_device {
> bool connected;
> bool active;
> bool suspended;
> + bool use_fw_training;
>
> const struct firmware *fw; /* cdn dp firmware */
> unsigned int fw_version; /* cdn fw version */
> @@ -106,6 +107,7 @@ struct cdn_dp_device {
> u8 ports;
> u8 lanes;
> int active_port;
> + u8 train_set[4];
>
> u8 dpcd[DP_RECEIVER_CAP_SIZE];
> bool sink_has_audio;
> diff --git a/drivers/gpu/drm/rockchip/cdn-dp-link-training.c b/drivers/gpu/drm/rockchip/cdn-dp-link-training.c
> new file mode 100644
> index 0000000..73c3290
> --- /dev/null
> +++ b/drivers/gpu/drm/rockchip/cdn-dp-link-training.c
> @@ -0,0 +1,420 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) Fuzhou Rockchip Electronics Co.Ltd
> + * Author: Chris Zhong <zyw@...k-chips.com>
> + */
> +
> +#include <linux/device.h>
> +#include <linux/delay.h>
> +#include <linux/phy/phy.h>
> +#include <soc/rockchip/rockchip_phy_typec.h>
> +
> +#include "cdn-dp-core.h"
> +#include "cdn-dp-reg.h"
> +
> +static void cdn_dp_set_signal_levels(struct cdn_dp_device *dp)
> +{
> + struct cdn_dp_port *port = dp->port[dp->active_port];
> + struct rockchip_typec_phy *tcphy = phy_get_drvdata(port->phy);
> +
> + int rate = drm_dp_bw_code_to_link_rate(dp->link.rate);
> + u8 swing = (dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK) >>
> + DP_TRAIN_VOLTAGE_SWING_SHIFT;
> + u8 pre_emphasis = (dp->train_set[0] & DP_TRAIN_PRE_EMPHASIS_MASK)
> + >> DP_TRAIN_PRE_EMPHASIS_SHIFT;
> +
> + tcphy->typec_phy_config(port->phy, rate, dp->link.num_lanes,
> + swing, pre_emphasis);
> +}
> +
> +static int cdn_dp_set_pattern(struct cdn_dp_device *dp, uint8_t dp_train_pat)
> +{
> + u32 phy_config, global_config;
> + int ret;
> + uint8_t pattern = dp_train_pat & DP_TRAINING_PATTERN_MASK;
> +
> + global_config = NUM_LANES(dp->link.num_lanes - 1) | SST_MODE |
> + GLOBAL_EN | RG_EN | ENC_RST_DIS | WR_VHSYNC_FALL;
> +
> + phy_config = DP_TX_PHY_ENCODER_BYPASS(0) |
> + DP_TX_PHY_SKEW_BYPASS(0) |
> + DP_TX_PHY_DISPARITY_RST(0) |
> + DP_TX_PHY_LANE0_SKEW(0) |
> + DP_TX_PHY_LANE1_SKEW(1) |
> + DP_TX_PHY_LANE2_SKEW(2) |
> + DP_TX_PHY_LANE3_SKEW(3) |
> + DP_TX_PHY_10BIT_ENABLE(0);
> +
> + if (pattern != DP_TRAINING_PATTERN_DISABLE) {
> + global_config |= NO_VIDEO;
> + phy_config |= DP_TX_PHY_TRAINING_ENABLE(1) |
> + DP_TX_PHY_SCRAMBLER_BYPASS(1) |
> + DP_TX_PHY_TRAINING_PATTERN(pattern);
> + }
> +
> + ret = cdn_dp_reg_write(dp, DP_FRAMER_GLOBAL_CONFIG, global_config);
> + if (ret) {
> + DRM_ERROR("fail to set DP_FRAMER_GLOBAL_CONFIG, error: %d\n",
> + ret);
> + return ret;
> + }
> +
> + ret = cdn_dp_reg_write(dp, DP_TX_PHY_CONFIG_REG, phy_config);
> + if (ret) {
> + DRM_ERROR("fail to set DP_TX_PHY_CONFIG_REG, error: %d\n",
> + ret);
> + return ret;
> + }
> +
> + ret = cdn_dp_reg_write(dp, DPTX_LANE_EN, BIT(dp->link.num_lanes) - 1);
> + if (ret) {
> + DRM_ERROR("fail to set DPTX_LANE_EN, error: %d\n", ret);
> + return ret;
> + }
> +
> + if (drm_dp_enhanced_frame_cap(dp->dpcd))
> + ret = cdn_dp_reg_write(dp, DPTX_ENHNCD, 1);
> + else
> + ret = cdn_dp_reg_write(dp, DPTX_ENHNCD, 0);
> + if (ret)
> + DRM_ERROR("failed to set DPTX_ENHNCD, error: %x\n", ret);
> +
> + return ret;
> +}
> +
> +static u8 cdn_dp_pre_emphasis_max(u8 voltage_swing)
> +{
> + switch (voltage_swing & DP_TRAIN_VOLTAGE_SWING_MASK) {
> + case DP_TRAIN_VOLTAGE_SWING_LEVEL_0:
> + return DP_TRAIN_PRE_EMPH_LEVEL_3;
> + case DP_TRAIN_VOLTAGE_SWING_LEVEL_1:
> + return DP_TRAIN_PRE_EMPH_LEVEL_2;
> + case DP_TRAIN_VOLTAGE_SWING_LEVEL_2:
> + return DP_TRAIN_PRE_EMPH_LEVEL_1;
> + default:
> + return DP_TRAIN_PRE_EMPH_LEVEL_0;
> + }
> +}
> +
> +static void cdn_dp_get_adjust_train(struct cdn_dp_device *dp,
> + uint8_t link_status[DP_LINK_STATUS_SIZE])
> +{
> + int i;
> + uint8_t v = 0, p = 0;
> + uint8_t preemph_max;
> +
> + for (i = 0; i < dp->link.num_lanes; i++) {
> + v = max(v, drm_dp_get_adjust_request_voltage(link_status, i));
> + p = max(p, drm_dp_get_adjust_request_pre_emphasis(link_status,
> + i));
> + }
> +
> + if (v >= VOLTAGE_LEVEL_2)
> + v = VOLTAGE_LEVEL_2 | DP_TRAIN_MAX_SWING_REACHED;
> +
> + preemph_max = cdn_dp_pre_emphasis_max(v);
> + if (p >= preemph_max)
> + p = preemph_max | DP_TRAIN_MAX_PRE_EMPHASIS_REACHED;
> +
> + for (i = 0; i < dp->link.num_lanes; i++)
> + dp->train_set[i] = v | p;
> +}
> +
> +/*
> + * Pick training pattern for channel equalization. Training Pattern 3 for HBR2
> + * or 1.2 devices that support it, Training Pattern 2 otherwise.
> + */
> +static u32 cdn_dp_select_chaneq_pattern(struct cdn_dp_device *dp)
> +{
> + u32 training_pattern = DP_TRAINING_PATTERN_2;
> +
> + /*
> + * cdn dp support HBR2 also support TPS3. TPS3 support is also mandatory
> + * for downstream devices that support HBR2. However, not all sinks
> + * follow the spec.
> + */
> + if (drm_dp_tps3_supported(dp->dpcd))
> + training_pattern = DP_TRAINING_PATTERN_3;
> + else
> + DRM_DEBUG_KMS("5.4 Gbps link rate without sink TPS3 support\n");
> +
> + return training_pattern;
> +}
> +
> +
> +static bool cdn_dp_link_max_vswing_reached(struct cdn_dp_device *dp)
> +{
> + int lane;
> +
> + for (lane = 0; lane < dp->link.num_lanes; lane++)
> + if ((dp->train_set[lane] & DP_TRAIN_MAX_SWING_REACHED) == 0)
> + return false;
> +
> + return true;
> +}
> +
> +static int cdn_dp_update_link_train(struct cdn_dp_device *dp)
> +{
> + int ret;
> +
> + cdn_dp_set_signal_levels(dp);
> +
> + ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET,
> + dp->train_set, dp->link.num_lanes);
> + if (ret != dp->link.num_lanes)
> + return -EINVAL;
> +
> + return 0;
> +}
> +
> +static int cdn_dp_set_link_train(struct cdn_dp_device *dp,
> + uint8_t dp_train_pat)
> +{
> + uint8_t buf[sizeof(dp->train_set) + 1];
> + int ret, len;
> +
> + buf[0] = dp_train_pat;
> + if ((dp_train_pat & DP_TRAINING_PATTERN_MASK) ==
> + DP_TRAINING_PATTERN_DISABLE) {
> + /* don't write DP_TRAINING_LANEx_SET on disable */
> + len = 1;
> + } else {
> + /* DP_TRAINING_LANEx_SET follow DP_TRAINING_PATTERN_SET */
> + memcpy(buf + 1, dp->train_set, dp->link.num_lanes);
> + len = dp->link.num_lanes + 1;
> + }
> +
> + ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_PATTERN_SET,
> + buf, len);
> + if (ret != len)
> + return -EINVAL;
> +
> + return 0;
> +}
> +
> +static int cdn_dp_reset_link_train(struct cdn_dp_device *dp,
> + uint8_t dp_train_pat)
> +{
> + int ret;
> +
> + memset(dp->train_set, 0, sizeof(dp->train_set));
> +
> + cdn_dp_set_signal_levels(dp);
> +
> + ret = cdn_dp_set_pattern(dp, dp_train_pat);
> + if (ret)
> + return ret;
> +
> + return cdn_dp_set_link_train(dp, dp_train_pat);
> +}
> +
> +/* Enable corresponding port and start training pattern 1 */
> +static int cdn_dp_link_training_clock_recovery(struct cdn_dp_device *dp)
> +{
> + u8 voltage;
> + u8 link_status[DP_LINK_STATUS_SIZE];
> + u32 voltage_tries, max_vswing_tries;
> + int ret;
> +
> + /* clock recovery */
> + ret = cdn_dp_reset_link_train(dp, DP_TRAINING_PATTERN_1 |
> + DP_LINK_SCRAMBLING_DISABLE);
> + if (ret) {
> + DRM_ERROR("failed to start link train\n");
> + return ret;
> + }
> +
> + voltage_tries = 1;
> + max_vswing_tries = 0;
> + for (;;) {
> + drm_dp_link_train_clock_recovery_delay(dp->dpcd);
> + if (drm_dp_dpcd_read_link_status(&dp->aux, link_status) !=
> + DP_LINK_STATUS_SIZE) {
> + DRM_ERROR("failed to get link status\n");
> + return -EINVAL;
> + }
> +
> + if (drm_dp_clock_recovery_ok(link_status, dp->link.num_lanes)) {
> + DRM_DEBUG_KMS("clock recovery OK\n");
> + return 0;
> + }
> +
> + if (voltage_tries >= 5) {
> + DRM_DEBUG_KMS("Same voltage tried 5 times\n");
> + return -EINVAL;
> + }
> +
> + if (max_vswing_tries >= 1) {
> + DRM_DEBUG_KMS("Max Voltage Swing reached\n");
> + return -EINVAL;
> + }
> +
> + voltage = dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK;
> +
> + /* Update training set as requested by target */
> + cdn_dp_get_adjust_train(dp, link_status);
> + if (cdn_dp_update_link_train(dp)) {
> + DRM_ERROR("failed to update link training\n");
> + return -EINVAL;
> + }
> +
> + if ((dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK) ==
> + voltage)
> + ++voltage_tries;
> + else
> + voltage_tries = 1;
> +
> + if (cdn_dp_link_max_vswing_reached(dp))
> + ++max_vswing_tries;
> + }
> +}
> +
> +static int cdn_dp_link_training_channel_equalization(struct cdn_dp_device *dp)
> +{
> + int tries, ret;
> + u32 training_pattern;
> + uint8_t link_status[DP_LINK_STATUS_SIZE];
> +
> + training_pattern = cdn_dp_select_chaneq_pattern(dp);
> + training_pattern |= DP_LINK_SCRAMBLING_DISABLE;
> +
> + ret = cdn_dp_set_pattern(dp, training_pattern);
> + if (ret)
> + return ret;
> +
> + ret = cdn_dp_set_link_train(dp, training_pattern);
> + if (ret) {
> + DRM_ERROR("failed to start channel equalization\n");
> + return ret;
> + }
> +
> + for (tries = 0; tries < 5; tries++) {
> + drm_dp_link_train_channel_eq_delay(dp->dpcd);
> + if (drm_dp_dpcd_read_link_status(&dp->aux, link_status) !=
> + DP_LINK_STATUS_SIZE) {
> + DRM_ERROR("failed to get link status\n");
> + break;
> + }
> +
> + /* Make sure clock is still ok */
> + if (!drm_dp_clock_recovery_ok(link_status,
> + dp->link.num_lanes)) {
> + DRM_DEBUG_KMS("Clock recovery check failed\n");
> + break;
> + }
> +
> + if (drm_dp_channel_eq_ok(link_status, dp->link.num_lanes)) {
> + DRM_DEBUG_KMS("Channel EQ done\n");
> + return 0;
> + }
> +
> + /* Update training set as requested by target */
> + cdn_dp_get_adjust_train(dp, link_status);
> + if (cdn_dp_update_link_train(dp)) {
> + DRM_ERROR("failed to update link training\n");
> + break;
> + }
> + }
> +
> + /* Try 5 times, else fail and try at lower BW */
> + if (tries == 5)
> + DRM_DEBUG_KMS("Channel equalization failed 5 times\n");
> +
> + return -EINVAL;
> +}
> +
> +static int cdn_dp_stop_link_train(struct cdn_dp_device *dp)
> +{
> + int ret = cdn_dp_set_pattern(dp, DP_TRAINING_PATTERN_DISABLE);
> +
> + if (ret)
> + return ret;
> +
> + return cdn_dp_set_link_train(dp, DP_TRAINING_PATTERN_DISABLE);
> +}
> +
> +static int cdn_dp_get_lower_link_rate(struct cdn_dp_device *dp)
> +{
> + switch (dp->link.rate) {
> + case DP_LINK_BW_1_62:
> + return -EINVAL;
> + case DP_LINK_BW_2_7:
> + dp->link.rate = DP_LINK_BW_1_62;
> + break;
> + case DP_LINK_BW_5_4:
> + dp->link.rate = DP_LINK_BW_2_7;
> + break;
> + default:
> + dp->link.rate = DP_LINK_BW_5_4;
> + break;
> + }
> +
> + return 0;
> +}
> +
> +int cdn_dp_software_train_link(struct cdn_dp_device *dp)
> +{
> + int ret, stop_err;
> + u8 link_config[2];
> + u32 rate, sink_max, source_max;
> +
> + ret = drm_dp_dpcd_read(&dp->aux, DP_DPCD_REV, dp->dpcd,
> + sizeof(dp->dpcd));
> + if (ret < 0) {
> + DRM_DEV_ERROR(dp->dev, "Failed to get caps %d\n", ret);
> + return ret;
> + }
> +
> + source_max = dp->lanes;
> + sink_max = drm_dp_max_lane_count(dp->dpcd);
> + dp->link.num_lanes = min(source_max, sink_max);
> +
> + source_max = drm_dp_bw_code_to_link_rate(CDN_DP_MAX_LINK_RATE);
> + sink_max = drm_dp_max_link_rate(dp->dpcd);
> + rate = min(source_max, sink_max);
> + dp->link.rate = drm_dp_link_rate_to_bw_code(rate);
> +
> + link_config[0] = 0;
> + link_config[1] = 0;
> + if (dp->dpcd[DP_MAIN_LINK_CHANNEL_CODING] & 0x01)
> + link_config[1] = DP_SET_ANSI_8B10B;
> + drm_dp_dpcd_write(&dp->aux, DP_DOWNSPREAD_CTRL, link_config, 2);
> +
> + while (true) {
> +
> + /* Write the link configuration data */
> + link_config[0] = dp->link.rate;
> + link_config[1] = dp->link.num_lanes;
> + if (drm_dp_enhanced_frame_cap(dp->dpcd))
> + link_config[1] |= DP_LANE_COUNT_ENHANCED_FRAME_EN;
> + drm_dp_dpcd_write(&dp->aux, DP_LINK_BW_SET, link_config, 2);
> +
> + ret = cdn_dp_link_training_clock_recovery(dp);
> + if (ret) {
> + if (!cdn_dp_get_lower_link_rate(dp))
> + continue;
> +
> + DRM_ERROR("training clock recovery failed: %d\n", ret);
> + break;
> + }
> +
> + ret = cdn_dp_link_training_channel_equalization(dp);
> + if (ret) {
> + if (!cdn_dp_get_lower_link_rate(dp))
> + continue;
> +
> + DRM_ERROR("training channel eq failed: %d\n", ret);
> + break;
> + }
> +
> + break;
> + }
> +
> + stop_err = cdn_dp_stop_link_train(dp);
> + if (stop_err) {
> + DRM_ERROR("stop training fail, error: %d\n", stop_err);
> + return stop_err;
> + }
> +
> + return ret;
> +}
> diff --git a/drivers/gpu/drm/rockchip/cdn-dp-reg.c b/drivers/gpu/drm/rockchip/cdn-dp-reg.c
> index 979355d..e1273e6 100644
> --- a/drivers/gpu/drm/rockchip/cdn-dp-reg.c
> +++ b/drivers/gpu/drm/rockchip/cdn-dp-reg.c
> @@ -17,7 +17,9 @@
> #include <linux/delay.h>
> #include <linux/io.h>
> #include <linux/iopoll.h>
> +#include <linux/phy/phy.h>
> #include <linux/reset.h>
> +#include <soc/rockchip/rockchip_phy_typec.h>
>
> #include "cdn-dp-core.h"
> #include "cdn-dp-reg.h"
> @@ -189,7 +191,7 @@ static int cdn_dp_mailbox_send(struct cdn_dp_device *dp, u8 module_id,
> return 0;
> }
>
> -static int cdn_dp_reg_write(struct cdn_dp_device *dp, u16 addr, u32 val)
> +int cdn_dp_reg_write(struct cdn_dp_device *dp, u16 addr, u32 val)
> {
> u8 msg[6];
>
> @@ -609,6 +611,31 @@ int cdn_dp_train_link(struct cdn_dp_device *dp)
> {
> int ret;
>
> + /*
> + * DP firmware uses fixed phy config values to do training, but some
> + * boards need to adjust these values to fit for their unique hardware
> + * design. So if the phy is using custom config values, do software
> + * link training instead of relying on firmware, if software training
> + * fail, keep firmware training as a fallback if sw training fails.
> + */
> + ret = cdn_dp_software_train_link(dp);
> + if (ret) {
> + DRM_DEV_ERROR(dp->dev,
> + "Failed to do software training %d\n", ret);
> + goto do_fw_training;
> + }
> + ret = cdn_dp_reg_write(dp, SOURCE_HDTX_CAR, 0xf);
> + if (ret) {
> + DRM_DEV_ERROR(dp->dev,
> + "Failed to write SOURCE_HDTX_CAR register %d\n", ret);
> + goto do_fw_training;
> + }
> + dp->use_fw_training = false;
> + return 0;
> +
> +do_fw_training:
> + dp->use_fw_training = true;
> + DRM_DEV_DEBUG_KMS(dp->dev, "use fw training\n");
> ret = cdn_dp_training_start(dp);
> if (ret) {
> DRM_DEV_ERROR(dp->dev, "Failed to start training %d\n", ret);
> @@ -623,7 +650,7 @@ int cdn_dp_train_link(struct cdn_dp_device *dp)
>
> DRM_DEV_DEBUG_KMS(dp->dev, "rate:0x%x, lanes:%d\n", dp->link.rate,
> dp->link.num_lanes);
> - return ret;
> + return 0;
> }
>
> int cdn_dp_set_video_status(struct cdn_dp_device *dp, int active)
> diff --git a/drivers/gpu/drm/rockchip/cdn-dp-reg.h b/drivers/gpu/drm/rockchip/cdn-dp-reg.h
> index 6580b11..3420771 100644
> --- a/drivers/gpu/drm/rockchip/cdn-dp-reg.h
> +++ b/drivers/gpu/drm/rockchip/cdn-dp-reg.h
> @@ -137,7 +137,7 @@
> #define HPD_EVENT_MASK 0x211c
> #define HPD_EVENT_DET 0x2120
>
> -/* dpyx framer addr */
> +/* dptx framer addr */
> #define DP_FRAMER_GLOBAL_CONFIG 0x2200
> #define DP_SW_RESET 0x2204
> #define DP_FRAMER_TU 0x2208
> @@ -431,6 +431,40 @@
> /* Reference cycles when using lane clock as reference */
> #define LANE_REF_CYC 0x8000
>
> +/* register CM_VID_CTRL */
> +#define LANE_VID_REF_CYC(x) (((x) & (BIT(24) - 1)) << 0)
> +#define NMVID_MEAS_TOLERANCE(x) (((x) & 0xf) << 24)
> +
> +/* register DP_TX_PHY_CONFIG_REG */
> +#define DP_TX_PHY_TRAINING_ENABLE(x) ((x) & 1)
> +#define DP_TX_PHY_TRAINING_TYPE_PRBS7 (0 << 1)
> +#define DP_TX_PHY_TRAINING_TYPE_TPS1 (1 << 1)
> +#define DP_TX_PHY_TRAINING_TYPE_TPS2 (2 << 1)
> +#define DP_TX_PHY_TRAINING_TYPE_TPS3 (3 << 1)
> +#define DP_TX_PHY_TRAINING_TYPE_TPS4 (4 << 1)
> +#define DP_TX_PHY_TRAINING_TYPE_PLTPAT (5 << 1)
> +#define DP_TX_PHY_TRAINING_TYPE_D10_2 (6 << 1)
> +#define DP_TX_PHY_TRAINING_TYPE_HBR2CPAT (8 << 1)
> +#define DP_TX_PHY_TRAINING_PATTERN(x) ((x) << 1)
> +#define DP_TX_PHY_SCRAMBLER_BYPASS(x) (((x) & 1) << 5)
> +#define DP_TX_PHY_ENCODER_BYPASS(x) (((x) & 1) << 6)
> +#define DP_TX_PHY_SKEW_BYPASS(x) (((x) & 1) << 7)
> +#define DP_TX_PHY_DISPARITY_RST(x) (((x) & 1) << 8)
> +#define DP_TX_PHY_LANE0_SKEW(x) (((x) & 7) << 9)
> +#define DP_TX_PHY_LANE1_SKEW(x) (((x) & 7) << 12)
> +#define DP_TX_PHY_LANE2_SKEW(x) (((x) & 7) << 15)
> +#define DP_TX_PHY_LANE3_SKEW(x) (((x) & 7) << 18)
> +#define DP_TX_PHY_10BIT_ENABLE(x) (((x) & 1) << 21)
> +
> +/* register DP_FRAMER_GLOBAL_CONFIG */
> +#define NUM_LANES(x) ((x) & 3)
> +#define SST_MODE (0 << 2)
> +#define RG_EN (0 << 4)
> +#define GLOBAL_EN BIT(3)
> +#define NO_VIDEO BIT(5)
> +#define ENC_RST_DIS BIT(6)
> +#define WR_VHSYNC_FALL BIT(7)
> +
> enum voltage_swing_level {
> VOLTAGE_LEVEL_0,
> VOLTAGE_LEVEL_1,
> @@ -476,6 +510,7 @@ int cdn_dp_set_host_cap(struct cdn_dp_device *dp, u8 lanes, bool flip);
> int cdn_dp_event_config(struct cdn_dp_device *dp);
> u32 cdn_dp_get_event(struct cdn_dp_device *dp);
> int cdn_dp_get_hpd_status(struct cdn_dp_device *dp);
> +int cdn_dp_reg_write(struct cdn_dp_device *dp, u16 addr, u32 val);
> ssize_t cdn_dp_dpcd_write(struct cdn_dp_device *dp, u32 addr,
> u8 *data, u16 len);
> ssize_t cdn_dp_dpcd_read(struct cdn_dp_device *dp, u32 addr,
> @@ -489,4 +524,5 @@ int cdn_dp_config_video(struct cdn_dp_device *dp);
> int cdn_dp_audio_stop(struct cdn_dp_device *dp, struct audio_info *audio);
> int cdn_dp_audio_mute(struct cdn_dp_device *dp, bool enable);
> int cdn_dp_audio_config(struct cdn_dp_device *dp, struct audio_info *audio);
> +int cdn_dp_software_train_link(struct cdn_dp_device *dp);
> #endif /* _CDN_DP_REG_H */
> --
> 2.7.4
>
Tested-by: Enric Balletbo i Serra <enric.balletbo@...labora.com>
Powered by blists - more mailing lists