linux-kernel - Re: [PATCH v3 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20180609084615.6fba31ec@bbrezillon>
Date:   Sat, 9 Jun 2018 08:46:15 +0200
From:   Boris Brezillon <boris.brezillon@...tlin.com>
To:     Stefan Agner <stefan@...er.ch>
Cc:     mark.rutland@....com, benjamin.lindqvist@...ian.se,
        pgaikwad@...dia.com, dev@...xeye.de, mirza.krak@...il.com,
        richard@....at, pdeschrijver@...dia.com,
        linux-kernel@...r.kernel.org, krzk@...nel.org,
        jonathanh@...dia.com, marek.vasut@...il.com,
        devicetree@...r.kernel.org, robh+dt@...nel.org,
        thierry.reding@...il.com, marcel@...wiler.com,
        miquel.raynal@...tlin.com, linux-tegra@...r.kernel.org,
        linux-mtd@...ts.infradead.org, Dmitry Osipenko <digetx@...il.com>,
        computersforpeace@...il.com, dwmw2@...radead.org
Subject: Re: [PATCH v3 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash
 controller driver

On Sat, 9 Jun 2018 08:41:57 +0200
Boris Brezillon <boris.brezillon@...tlin.com> wrote:

> On Sat, 09 Jun 2018 08:23:51 +0200
> Stefan Agner <stefan@...er.ch> wrote:
> 
> > On 09.06.2018 07:52, Boris Brezillon wrote:
> > > On Fri, 08 Jun 2018 23:51:01 +0200
> > > Stefan Agner <stefan@...er.ch> wrote:
> > > 
> > >   
> > >> >
> > >> > void tegra_nand_controller_reset(struct tegra_nand_controller *ctrl)
> > >> > {
> > >> > 	int err;
> > >> >
> > >> > 	disable_irq(ctrl->irq);
> > >> >
> > >> > 	err = reset_control_reset(ctrl->rst);
> > >> > 	if (err) {
> > >> > 		dev_err(ctrl->dev, "Failed to reset HW: %d\n", err);
> > >> > 		msleep(HW_TIMEOUT);
> > >> > 	}
> > >> >
> > >> > 	writel_relaxed(NAND_CMD_STATUS, ctrl->regs + HWSTATUS_CMD);
> > >> > 	writel_relaxed(HWSTATUS_MASK, ctrl->regs + HWSTATUS_MASK);
> > >> > 	writel_relaxed(INT_MASK, ctrl->regs + ISR);  
> > >>
> > >> If we do a controller reset, there is much more state than that which
> > >> needs to be restored. A lot of it is not readily available currently
> > >> (timing, ECC settings...)  
> > > 
> > > This is actually a good test to detect what is not properly initialized
> > > by the driver. Timings should be configured correctly through  
> > > ->setup_data_interface(). ECC engine should be disabled by default and  
> > > only enabled when ->{read,write}_page() is called.
> > >   
> > 
> > Is setup_data_interface guaranteed to be called after a failed
> > ->exec_op()/{read,write}_page()?
> 
> No. Maybe I misunderstood when tegra_nand_controller_reset() was
> supposed to be called. That's something I would call only once, early
> in the probe function, so that the controller is placed in a well-known
> state before we start using it. Definitely not something you should
> call after each error.

Note that if you really want to reset the controller after an error,
you should also iterate over all chips and call nand_reset() on them.