linux-kernel - Re: [PATCH v2] mmc: sdhci-esdhc-imx: allow 1.8V modes without 100/200MHz pinctrl states

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <69f6122b8a69f1ab41d2ef8274321689@agner.ch>
Date:   Thu, 05 Jul 2018 13:22:33 +0200
From:   Stefan Agner <stefan@...er.ch>
To:     Ulf Hansson <ulf.hansson@...aro.org>
Cc:     Adrian Hunter <adrian.hunter@...el.com>,
        Fabio Estevam <fabio.estevam@....com>,
        Haibo Chen <haibo.chen@....com>,
        Aisheng Dong <aisheng.dong@....com>,
        Michael Trimarchi <michael@...rulasolutions.com>,
        Russell King <rmk+kernel@...linux.org.uk>,
        linux-mmc@...r.kernel.org,
        Linux Kernel Mailing List <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v2] mmc: sdhci-esdhc-imx: allow 1.8V modes without
 100/200MHz pinctrl states

On 05.07.2018 11:48, Ulf Hansson wrote:
> On 4 July 2018 at 17:18, Stefan Agner <stefan@...er.ch> wrote:
>> On 04.07.2018 17:07, Stefan Agner wrote:
>>> If pinctrl nodes for 100/200MHz are missing, the controller should
>>> not select any mode which need signal frequencies 100MHz or higher.
>>> To prevent such speed modes the driver currently uses the quirk flag
>>> SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V
>>> signaling is required for all faster modes and slower modes use 3.3V
>>> signaling only.
>>>
>>> However, there are eMMC modes which use 1.8V signaling and run below
>>> 100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this
>>> mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply
>>> the stack has no valid mode to use. In this tenuous situation the
>>> kernel continuously prints voltage switching errors:
>>>   mmc1: Switching to 3.3V signalling voltage failed
>>>
>>> Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by
>>> altering the SDHCI capability register. With that the stack is able
>>> to select 1.8V modes even if no faster pinctrl states are available:
>>>   # cat /sys/kernel/debug/mmc1/ios
>>>   ...
>>>   timing spec:    8 (mmc DDR52)
>>>   signal voltage: 1 (1.80 V)
>>>   ...
>>>
>>> Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch
>>> Signed-off-by: Stefan Agner <stefan@...er.ch>
>>> ---
>>
>> Btw, I still get the switching error once during boot-up:
>>   mmc1: Switching to 3.3V signalling voltage failed
> 
> I guess the this happens then also at system resume?
> 
> The core tries first with 3.3 then if it fails, it continues with 1.8V, etc.
> 
>>
>> This is due to the call from mmc_set_initial_signal_voltage. It is a bit
>> unfortunate since this is printed as a warning. Not sure if that could
>> be prevented somehow?
> 
> Seems like SDHCI_SIGNALING_330 should not be set, unless 3.3V I/O is
> supported. That should avoid SDHCI from trying and instead just
> returning an error code immediately.
> 
> This seems like a generic issues for all SDHCI variant drivers.

Hm, can we resolve this in a generic fashion?

E.g something like this in sdhci_setup_host():

if (!regulator_is_supported_voltage(mmc->supply.vqmmc, 3200000,
3450000))
	host->flags &= ~SDHCI_SIGNALING_330;

--
Stefan