Message-Id: <1539004739-32060-4-git-send-email-vbadigan@codeaurora.org>
Date:   Mon,  8 Oct 2018 18:48:59 +0530
From:   Veerabhadrarao Badiganti <vbadigan@...eaurora.org>
To:     adrian.hunter@...el.com, ulf.hansson@...aro.org,
        robh+dt@...nel.org, evgreen@...omium.org, dianders@...gle.com
Cc:     asutoshd@...eaurora.org, riteshh@...eaurora.org,
        stummala@...eaurora.org, sayalil@...eaurora.org,
        linux-mmc@...r.kernel.org, linux-arm-msm@...r.kernel.org,
        Vijay Viswanath <vviswana@...eaurora.org>,
        Venkat Gopalakrishnan <venkatg@...eaurora.org>,
        Veerabhadrarao Badiganti <vbadigan@...eaurora.org>,
        linux-kernel@...r.kernel.org (open list)
Subject: [PATCH V3 3/3] mmc: sdhci-msm: Use internal voltage control

From: Vijay Viswanath <vviswana@...eaurora.org>

Some sdhci-msm controllers require that voltage switching be done after
the HW is ready for it. The HW informs its readiness through power irq.
The voltage switching should happen only then.

Use the quirk for internal voltage switching and then control the
voltage switching using power irq.

Signed-off-by: Asutosh Das <asutoshd@...eaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@...eaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@...eaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@...eaurora.org>
---
 drivers/mmc/host/sdhci-msm.c | 212 +++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 204 insertions(+), 8 deletions(-)

diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 3cc8bfe..6918e70 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -43,7 +43,9 @@
 #define CORE_PWRCTL_IO_LOW	BIT(2)
 #define CORE_PWRCTL_IO_HIGH	BIT(3)
 #define CORE_PWRCTL_BUS_SUCCESS BIT(0)
+#define CORE_PWRCTL_BUS_FAIL    BIT(1)
 #define CORE_PWRCTL_IO_SUCCESS	BIT(2)
+#define CORE_PWRCTL_IO_FAIL     BIT(3)
 #define REQ_BUS_OFF		BIT(0)
 #define REQ_BUS_ON		BIT(1)
 #define REQ_IO_LOW		BIT(2)
@@ -258,6 +260,10 @@ struct sdhci_msm_host {
 	bool mci_removed;
 	const struct sdhci_msm_variant_ops *var_ops;
 	const struct sdhci_msm_offset *offset;
+	bool vmmc_load;
+	u32 vmmc_level[2];
+	bool vqmmc_load;
+	u32 vqmmc_level[2];
 };
 
 static const struct sdhci_msm_offset *sdhci_priv_msm_offset(struct sdhci_host *host)
@@ -1211,6 +1217,74 @@ static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host,
 		sdhci_msm_hs400(host, &mmc->ios);
 }
 
+static int sdhci_msm_set_vmmc(struct sdhci_msm_host *msm_host,
+			      struct mmc_host *mmc, int level)
+{
+	int load = msm_host->vmmc_level[level];
+	int ret;
+
+	if (IS_ERR(mmc->supply.vmmc))
+		return 0;
+
+	if (msm_host->vmmc_load) {
+		ret = regulator_set_load(mmc->supply.vmmc, load);
+		if (ret)
+			goto out;
+	}
+
+	ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, mmc->ios.vdd);
+out:
+	if (ret)
+		pr_err("%s: vmmc set load/ocr failed: %d\n",
+				mmc_hostname(mmc), ret);
+
+	return ret;
+}
+
+static int sdhci_msm_set_vqmmc(struct sdhci_msm_host *msm_host,
+			      struct mmc_host *mmc, int level)
+{
+	int load = msm_host->vqmmc_level[level];
+	int ret;
+	struct mmc_ios ios;
+
+	if (IS_ERR(mmc->supply.vqmmc))
+		return 0;
+
+	if (msm_host->vqmmc_load) {
+		ret = regulator_set_load(mmc->supply.vqmmc, load);
+		if (ret)
+			goto out;
+	}
+
+	/*
+	 * The IO voltage regulator may not always support a voltage close to
+	 * vdd. Set IO voltage based on capability of the regulator.
+	 */
+	if (level) {
+		if (msm_host->caps_0 & CORE_3_0V_SUPPORT)
+			ios.signal_voltage = MMC_SIGNAL_VOLTAGE_330;
+		else if (msm_host->caps_0 & CORE_1_8V_SUPPORT)
+			ios.signal_voltage = MMC_SIGNAL_VOLTAGE_180;
+		if (msm_host->caps_0 & CORE_VOLT_SUPPORT) {
+			pr_debug("%s: %s: setting signal voltage: %d\n",
+					mmc_hostname(mmc), __func__,
+					ios.signal_voltage);
+			ret = mmc_regulator_set_vqmmc(mmc, &ios);
+			if (ret)
+				goto out;
+		}
+		ret = regulator_enable(mmc->supply.vqmmc);
+	} else {
+		ret = regulator_disable(mmc->supply.vqmmc);
+	}
+out:
+	if (ret)
+		pr_err("%s: vqmmc failed: %d\n", mmc_hostname(mmc), ret);
+
+	return ret;
+}
+
 static inline void sdhci_msm_init_pwr_irq_wait(struct sdhci_msm_host *msm_host)
 {
 	init_waitqueue_head(&msm_host->pwr_irq_wait);
@@ -1314,8 +1388,9 @@ static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq)
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
+	struct mmc_host *mmc = host->mmc;
 	u32 irq_status, irq_ack = 0;
-	int retry = 10;
+	int retry = 10, ret = 0;
 	u32 pwr_state = 0, io_level = 0;
 	u32 config;
 	const struct sdhci_msm_offset *msm_offset = msm_host->offset;
@@ -1351,14 +1426,35 @@ static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq)
 
 	/* Handle BUS ON/OFF*/
 	if (irq_status & CORE_PWRCTL_BUS_ON) {
-		pwr_state = REQ_BUS_ON;
-		io_level = REQ_IO_HIGH;
-		irq_ack |= CORE_PWRCTL_BUS_SUCCESS;
+		ret = sdhci_msm_set_vmmc(msm_host, mmc, 1);
+		if (!ret)
+			ret = sdhci_msm_set_vqmmc(msm_host, mmc, 1);
+
+		if (!ret) {
+			pwr_state = REQ_BUS_ON;
+			io_level = REQ_IO_HIGH;
+			irq_ack |= CORE_PWRCTL_BUS_SUCCESS;
+		} else {
+			pr_err("%s: BUS_ON req failed(%d). irq_status: 0x%08x\n",
+					mmc_hostname(mmc), ret, irq_status);
+			irq_ack |= CORE_PWRCTL_BUS_FAIL;
+			sdhci_msm_set_vmmc(msm_host, mmc, 0);
+		}
 	}
 	if (irq_status & CORE_PWRCTL_BUS_OFF) {
-		pwr_state = REQ_BUS_OFF;
-		io_level = REQ_IO_LOW;
-		irq_ack |= CORE_PWRCTL_BUS_SUCCESS;
+		ret = sdhci_msm_set_vmmc(msm_host, mmc, 0);
+		if (!ret)
+			ret = sdhci_msm_set_vqmmc(msm_host, mmc, 0);
+
+		if (!ret) {
+			pwr_state = REQ_BUS_OFF;
+			io_level = REQ_IO_LOW;
+			irq_ack |= CORE_PWRCTL_BUS_SUCCESS;
+		} else {
+			pr_err("%s: BUS_ON req failed(%d). irq_status: 0x%08x\n",
+					mmc_hostname(mmc), ret, irq_status);
+			irq_ack |= CORE_PWRCTL_BUS_FAIL;
+		}
 	}
 	/* Handle IO LOW/HIGH */
 	if (irq_status & CORE_PWRCTL_IO_LOW) {
@@ -1370,6 +1466,15 @@ static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq)
 		irq_ack |= CORE_PWRCTL_IO_SUCCESS;
 	}
 
+	if (io_level && !IS_ERR(mmc->supply.vqmmc) && !pwr_state) {
+		ret = mmc_regulator_set_vqmmc(mmc, &mmc->ios);
+		if (ret)
+			pr_err("%s: IO_level setting failed(%d). signal_voltage: %d, vdd: %d irq_status: 0x%08x\n",
+					mmc_hostname(mmc), ret,
+					mmc->ios.signal_voltage, mmc->ios.vdd,
+					irq_status);
+	}
+
 	/*
 	 * The driver has to acknowledge the interrupt, switch voltages and
 	 * report back if it succeded or not to this register. The voltage
@@ -1605,6 +1710,91 @@ static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host)
 	pr_debug("%s: supported caps: 0x%08x\n", mmc_hostname(mmc), caps);
 }
 
+static int sdhci_msm_register_vreg(struct sdhci_msm_host *msm_host)
+{
+	int ret = 0;
+
+	ret = mmc_regulator_get_supply(msm_host->mmc);
+	if (ret)
+		return ret;
+	if (device_property_read_u32_array(&msm_host->pdev->dev,
+			"qcom,vmmc-current-level-microamp",
+			msm_host->vmmc_level, 2) >= 0)
+		msm_host->vmmc_load = true;
+	if (device_property_read_u32_array(&msm_host->pdev->dev,
+			"qcom,vqmmc-current-level-microamp",
+			msm_host->vqmmc_level, 2) >= 0)
+		msm_host->vqmmc_load = true;
+
+	sdhci_msm_set_regulator_caps(msm_host);
+
+	return 0;
+
+}
+
+static int sdhci_msm_start_signal_voltage_switch(struct mmc_host *mmc,
+				      struct mmc_ios *ios)
+{
+	struct sdhci_host *host = mmc_priv(mmc);
+	u16 ctrl;
+
+	/*
+	 * Signal Voltage Switching is only applicable for Host Controllers
+	 * v3.00 and above.
+	 */
+	if (host->version < SDHCI_SPEC_300)
+		return 0;
+
+	ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+
+	switch (ios->signal_voltage) {
+	case MMC_SIGNAL_VOLTAGE_330:
+		if (!(host->flags & SDHCI_SIGNALING_330))
+			return -EINVAL;
+		/* Set 1.8V Signal Enable in the Host Control2 register to 0 */
+		ctrl &= ~SDHCI_CTRL_VDD_180;
+		sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
+
+		/* 3.3V regulator output should be stable within 5 ms */
+		ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+		if (!(ctrl & SDHCI_CTRL_VDD_180))
+			return 0;
+
+		pr_warn("%s: 3.3V regulator output did not became stable\n",
+			mmc_hostname(mmc));
+
+		return -EAGAIN;
+	case MMC_SIGNAL_VOLTAGE_180:
+		if (!(host->flags & SDHCI_SIGNALING_180))
+			return -EINVAL;
+
+		/*
+		 * Enable 1.8V Signal Enable in the Host Control2
+		 * register
+		 */
+		ctrl |= SDHCI_CTRL_VDD_180;
+		sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
+
+		/* 1.8V regulator output should be stable within 5 ms */
+		ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+		if (ctrl & SDHCI_CTRL_VDD_180)
+			return 0;
+
+		pr_warn("%s: 1.8V regulator output did not became stable\n",
+			mmc_hostname(mmc));
+
+		return -EAGAIN;
+	case MMC_SIGNAL_VOLTAGE_120:
+		if (!(host->flags & SDHCI_SIGNALING_120))
+			return -EINVAL;
+		return 0;
+	default:
+		/* No signal voltage switch required */
+		return 0;
+	}
+
+}
+
 static const struct sdhci_msm_variant_ops mci_var_ops = {
 	.msm_readl_relaxed = sdhci_msm_mci_variant_readl_relaxed,
 	.msm_writel_relaxed = sdhci_msm_mci_variant_writel_relaxed,
@@ -1644,6 +1834,7 @@ static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host)
 	.set_uhs_signaling = sdhci_msm_set_uhs_signaling,
 	.write_w = sdhci_msm_writew,
 	.write_b = sdhci_msm_writeb,
+	.set_power = sdhci_set_power_noreg,
 };
 
 static const struct sdhci_pltfm_data sdhci_msm_pdata = {
@@ -1818,6 +2009,10 @@ static int sdhci_msm_probe(struct platform_device *pdev)
 				msm_offset->core_vendor_spec_capabilities0);
 	}
 
+	ret = sdhci_msm_register_vreg(msm_host);
+	if (ret)
+		goto clk_disable;
+
 	/*
 	 * Power on reset state may trigger power irq if previous status of
 	 * PWRCTL was either BUS_ON or IO_HIGH_V. So before enabling pwr irq
@@ -1862,11 +2057,12 @@ static int sdhci_msm_probe(struct platform_device *pdev)
 					 MSM_MMC_AUTOSUSPEND_DELAY_MS);
 	pm_runtime_use_autosuspend(&pdev->dev);
 
+	host->mmc_host_ops.start_signal_voltage_switch =
+		sdhci_msm_start_signal_voltage_switch;
 	host->mmc_host_ops.execute_tuning = sdhci_msm_execute_tuning;
 	ret = sdhci_add_host(host);
 	if (ret)
 		goto pm_runtime_disable;
-	sdhci_msm_set_regulator_caps(msm_host);
 
 	pm_runtime_mark_last_busy(&pdev->dev);
 	pm_runtime_put_autosuspend(&pdev->dev);
-- 
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project.

Powered by blists - more mailing lists