| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <4feccc4c-5873-5854-c1b8-6a32d6fc473f@st.com>
Date: Mon, 8 Apr 2019 08:20:09 +0000
From: Mickael GUENE <mickael.guene@...com>
To: Sakari Ailus <sakari.ailus@...ux.intel.com>
CC: "linux-media@...r.kernel.org" <linux-media@...r.kernel.org>,
"Hugues FRUCHET" <hugues.fruchet@...com>,
Mauro Carvalho Chehab <mchehab@...nel.org>,
Matt Ranostay <matt.ranostay@...sulko.com>,
Akinobu Mita <akinobu.mita@...il.com>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"David S. Miller" <davem@...emloft.net>,
Nicolas Ferre <nicolas.ferre@...rochip.com>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Hans Verkuil <hverkuil@...all.nl>,
"Ricardo Ribalda Delgado" <ricardo@...alda.com>,
Jason Chen <jasonx.z.chen@...el.com>,
Jacopo Mondi <jacopo+renesas@...ndi.org>,
Tianshu Qiu <tian.shu.qiu@...el.com>,
Bingbu Cao <bingbu.cao@...el.com>,
Alan Chiang <alanx.chiang@...el.com>
Subject: Re: [PATCH v4 2/2] media:st-mipid02: MIPID02 CSI-2 to PARALLEL bridge
driver
Hi Sakari,
On 4/6/19 12:56, Sakari Ailus wrote:
> Hi Mickael,
>
> On Wed, Mar 27, 2019 at 10:55:44AM +0100, Mickael Guene wrote:
>> This V4L2 subdev driver enables STMicroelectronics MIPID02 device.
>>
>> Signed-off-by: Mickael Guene <mickael.guene@...com>
>> ---
>>
>> Changes in v4:
>> - Add support of enum_mbus_code
>> - Only use V4L2_CID_PIXEL_RATE to compute link speed
>> - Use MEDIA_BUS_FMT_UYVY8_1X16 instead of MEDIA_BUS_FMT_UYVY8_2X8 for CSI-2 link
>> - Fix miscellaneous typos
>> - Fix wrong code behavior for set_fmt and get_fmt
>>
>> Changes in v3:
>> - Fix potential wrong error code for mipid02_stream_disable and mipid02_stream_enable
>> - Remove useless memset for ep in mipid02_parse_rx_ep and mipid02_parse_tx_ep
>> - Add second CSI-2 input pad even if it's not yet supported
>> - Add support of get_fmt, set_fmt and link_validate and only access subdev connected to mipid02
>>
>> Changes in v2:
>> - Merge MAINTAINERS patch 3 into patch 1 and 2
>> - Fix line too long in Kconfig
>> - Add missing delay after reset release
>> - Various style fixes
>> - Fix mipid02_stream_enable returning no error when mipid02_find_sensor failed
>>
>> MAINTAINERS | 1 +
>> drivers/media/i2c/Kconfig | 14 +
>> drivers/media/i2c/Makefile | 1 +
>> drivers/media/i2c/st-mipid02.c | 1043 ++++++++++++++++++++++++++++++++++++++++
>> 4 files changed, 1059 insertions(+)
>> create mode 100644 drivers/media/i2c/st-mipid02.c
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 74da99d..a14fe81 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -14673,6 +14673,7 @@ M: Mickael Guene <mickael.guene@...com>
>> L: linux-media@...r.kernel.org
>> T: git git://linuxtv.org/media_tree.git
>> S: Maintained
>> +F: drivers/media/i2c/st-mipid02.c
>> F: Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
>>
>> ST STM32 I2C/SMBUS DRIVER
>> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
>> index 1a1746b..2dc9e15 100644
>> --- a/drivers/media/i2c/Kconfig
>> +++ b/drivers/media/i2c/Kconfig
>> @@ -1135,6 +1135,20 @@ config VIDEO_I2C
>> To compile this driver as a module, choose M here: the
>> module will be called video-i2c
>>
>> +config VIDEO_ST_MIPID02
>> + tristate "STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge"
>> + depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
>> + depends on MEDIA_CAMERA_SUPPORT
>> + depends on MEDIA_CONTROLLER
>
> VIDEO_V4L2_SUBDEV_API already requires MEDIA_CONTROLLER, so
> MEDIA_CONTROLLER here is redundant.
>
ok I will remove it.
>> + select V4L2_FWNODE
>> + help
>> + Support for STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge.
>> + It is used to allow usage of CSI-2 sensor with PARALLEL port
>> + controller.
>> +
>> + To compile this driver as a module, choose M here: the
>> + module will be called st-mipid02.
>> +
>> endmenu
>>
>> endif
>> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
>> index a64fca8..d8ad9da 100644
>> --- a/drivers/media/i2c/Makefile
>> +++ b/drivers/media/i2c/Makefile
>> @@ -113,5 +113,6 @@ obj-$(CONFIG_VIDEO_IMX258) += imx258.o
>> obj-$(CONFIG_VIDEO_IMX274) += imx274.o
>> obj-$(CONFIG_VIDEO_IMX319) += imx319.o
>> obj-$(CONFIG_VIDEO_IMX355) += imx355.o
>> +obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o
>>
>> obj-$(CONFIG_SDR_MAX2175) += max2175.o
>> diff --git a/drivers/media/i2c/st-mipid02.c b/drivers/media/i2c/st-mipid02.c
>> new file mode 100644
>> index 0000000..1d09bae
>> --- /dev/null
>> +++ b/drivers/media/i2c/st-mipid02.c
>> @@ -0,0 +1,1043 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Driver for ST MIPID02 CSI-2 to PARALLEL bridge
>> + *
>> + * Copyright (C) STMicroelectronics SA 2019
>> + * Authors: Mickael Guene <mickael.guene@...com>
>> + * for STMicroelectronics.
>> + *
>> + *
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/delay.h>
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/i2c.h>
>> +#include <linux/module.h>
>> +#include <linux/of_graph.h>
>> +#include <linux/regulator/consumer.h>
>> +#include <media/v4l2-async.h>
>> +#include <media/v4l2-ctrls.h>
>> +#include <media/v4l2-device.h>
>> +#include <media/v4l2-fwnode.h>
>> +#include <media/v4l2-subdev.h>
>> +
>> +#define MIPID02_CLK_LANE_WR_REG1 0x01
>> +#define MIPID02_CLK_LANE_REG1 0x02
>> +#define MIPID02_CLK_LANE_REG3 0x04
>> +#define MIPID02_DATA_LANE0_REG1 0x05
>> +#define MIPID02_DATA_LANE0_REG2 0x06
>> +#define MIPID02_DATA_LANE1_REG1 0x09
>> +#define MIPID02_DATA_LANE1_REG2 0x0a
>> +#define MIPID02_MODE_REG1 0x14
>> +#define MIPID02_MODE_REG2 0x15
>> +#define MIPID02_DATA_ID_RREG 0x17
>> +#define MIPID02_DATA_SELECTION_CTRL 0x19
>> +#define MIPID02_PIX_WIDTH_CTRL 0x1e
>> +#define MIPID02_PIX_WIDTH_CTRL_EMB 0x1f
>> +
>> +/* Bits definition for MIPID02_CLK_LANE_REG1 */
>> +#define CLK_ENABLE BIT(0)
>> +/* Bits definition for MIPID02_CLK_LANE_REG3 */
>> +#define CLK_MIPI_CSI BIT(1)
>> +/* Bits definition for MIPID02_DATA_LANE0_REG1 */
>> +#define DATA_ENABLE BIT(0)
>> +/* Bits definition for MIPID02_DATA_LANEx_REG2 */
>> +#define DATA_MIPI_CSI BIT(0)
>> +/* Bits definition for MIPID02_MODE_REG1 */
>> +#define MODE_DATA_SWAP BIT(2)
>> +#define MODE_NO_BYPASS BIT(6)
>> +/* Bits definition for MIPID02_MODE_REG2 */
>> +#define MODE_HSYNC_ACTIVE_HIGH BIT(1)
>> +#define MODE_VSYNC_ACTIVE_HIGH BIT(2)
>> +/* Bits definition for MIPID02_DATA_SELECTION_CTRL */
>> +#define SELECTION_MANUAL_DATA BIT(2)
>> +#define SELECTION_MANUAL_WIDTH BIT(3)
>> +
>> +static const u32 mipid02_supported_fmt_codes[] = {
>> + MEDIA_BUS_FMT_SBGGR8_1X8, MEDIA_BUS_FMT_SGBRG8_1X8,
>> + MEDIA_BUS_FMT_SGRBG8_1X8, MEDIA_BUS_FMT_SRGGB8_1X8,
>> + MEDIA_BUS_FMT_SBGGR10_1X10, MEDIA_BUS_FMT_SGBRG10_1X10,
>> + MEDIA_BUS_FMT_SGRBG10_1X10, MEDIA_BUS_FMT_SRGGB10_1X10,
>> + MEDIA_BUS_FMT_SBGGR12_1X12, MEDIA_BUS_FMT_SGBRG12_1X12,
>> + MEDIA_BUS_FMT_SGRBG12_1X12, MEDIA_BUS_FMT_SRGGB12_1X12,
>> + MEDIA_BUS_FMT_UYVY8_1X16, MEDIA_BUS_FMT_BGR888_1X24
>> +};
>> +
>> +/* regulator supplies */
>> +static const char * const mipid02_supply_name[] = {
>> + "VDDE", /* 1.8V digital I/O supply */
>> + "VDDIN", /* 1V8 voltage regulator supply */
>> +};
>> +
>> +#define MIPID02_NUM_SUPPLIES ARRAY_SIZE(mipid02_supply_name)
>> +
>> +#define MIPID02_SINK_0 0
>> +#define MIPID02_SINK_1 1
>> +#define MIPID02_SOURCE 2
>> +#define MIPID02_PAD_NB 3
>> +
>> +struct mipid02_dev {
>> + struct i2c_client *i2c_client;
>> + struct regulator_bulk_data supplies[MIPID02_NUM_SUPPLIES];
>> + struct v4l2_subdev sd;
>> + struct media_pad pad[MIPID02_PAD_NB];
>> + struct clk *xclk;
>> + struct gpio_desc *reset_gpio;
>> + /* endpoints info */
>> + struct v4l2_fwnode_endpoint rx;
>> + u64 link_frequency;
>> + struct v4l2_fwnode_endpoint tx;
>> + /* remote source */
>> + struct v4l2_async_subdev asd;
>> + struct v4l2_async_notifier notifier;
>> + struct v4l2_subdev *s_subdev;
>> + /* registers */
>> + struct {
>> + u8 clk_lane_reg1;
>> + u8 data_lane0_reg1;
>> + u8 data_lane1_reg1;
>> + u8 mode_reg1;
>> + u8 mode_reg2;
>> + u8 data_id_rreg;
>> + u8 pix_width_ctrl;
>> + u8 pix_width_ctrl_emb;
>> + } r;
>> + /* lock to protect all members below */
>> + struct mutex lock;
>> + bool streaming;
>> + struct v4l2_mbus_framefmt fmt;
>> +};
>> +
>> +static int bpp_from_code(__u32 code)
>> +{
>> + switch (code) {
>> + case MEDIA_BUS_FMT_SBGGR8_1X8:
>> + case MEDIA_BUS_FMT_SGBRG8_1X8:
>> + case MEDIA_BUS_FMT_SGRBG8_1X8:
>> + case MEDIA_BUS_FMT_SRGGB8_1X8:
>> + return 8;
>> + case MEDIA_BUS_FMT_SBGGR10_1X10:
>> + case MEDIA_BUS_FMT_SGBRG10_1X10:
>> + case MEDIA_BUS_FMT_SGRBG10_1X10:
>> + case MEDIA_BUS_FMT_SRGGB10_1X10:
>> + return 10;
>> + case MEDIA_BUS_FMT_SBGGR12_1X12:
>> + case MEDIA_BUS_FMT_SGBRG12_1X12:
>> + case MEDIA_BUS_FMT_SGRBG12_1X12:
>> + case MEDIA_BUS_FMT_SRGGB12_1X12:
>> + return 12;
>> + case MEDIA_BUS_FMT_UYVY8_1X16:
>> + return 16;
>> + case MEDIA_BUS_FMT_BGR888_1X24:
>> + return 24;
>> + default:
>> + return 0;
>> + }
>> +}
>> +
>> +static u8 data_type_from_code(__u32 code)
>> +{
>> + switch (code) {
>> + case MEDIA_BUS_FMT_SBGGR8_1X8:
>> + case MEDIA_BUS_FMT_SGBRG8_1X8:
>> + case MEDIA_BUS_FMT_SGRBG8_1X8:
>> + case MEDIA_BUS_FMT_SRGGB8_1X8:
>> + return 0x2a;
>> + case MEDIA_BUS_FMT_SBGGR10_1X10:
>> + case MEDIA_BUS_FMT_SGBRG10_1X10:
>> + case MEDIA_BUS_FMT_SGRBG10_1X10:
>> + case MEDIA_BUS_FMT_SRGGB10_1X10:
>> + return 0x2b;
>> + case MEDIA_BUS_FMT_SBGGR12_1X12:
>> + case MEDIA_BUS_FMT_SGBRG12_1X12:
>> + case MEDIA_BUS_FMT_SGRBG12_1X12:
>> + case MEDIA_BUS_FMT_SRGGB12_1X12:
>> + return 0x2c;
>> + case MEDIA_BUS_FMT_UYVY8_1X16:
>> + return 0x1e;
>> + case MEDIA_BUS_FMT_BGR888_1X24:
>> + return 0x24;
>> + default:
>> + return 0;
>> + }
>> +}
>> +
>> +static void init_format(struct v4l2_mbus_framefmt *fmt)
>> +{
>> + fmt->code = MEDIA_BUS_FMT_SBGGR8_1X8;
>> + fmt->field = V4L2_FIELD_NONE;
>> + fmt->colorspace = V4L2_COLORSPACE_SRGB;
>> + fmt->ycbcr_enc = V4L2_MAP_YCBCR_ENC_DEFAULT(V4L2_COLORSPACE_SRGB);
>> + fmt->quantization = V4L2_QUANTIZATION_FULL_RANGE;
>> + fmt->xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(V4L2_COLORSPACE_SRGB);
>> + fmt->width = 640;
>> + fmt->height = 480;
>> +}
>> +
>> +static __u32 get_fmt_code(__u32 code)
>> +{
>> + unsigned int i;
>> +
>> + for (i = 0; i < ARRAY_SIZE(mipid02_supported_fmt_codes); i++) {
>> + if (code == mipid02_supported_fmt_codes[i])
>> + return code;
>> + }
>> +
>> + return mipid02_supported_fmt_codes[0];
>> +}
>> +
>> +static __u32 serial_to_parallel_code(__u32 serial)
>> +{
>> + if (serial == MEDIA_BUS_FMT_UYVY8_1X16)
>> + return MEDIA_BUS_FMT_UYVY8_2X8;
>> +
>> + return serial;
>> +}
>> +
>> +static inline struct mipid02_dev *to_mipid02_dev(struct v4l2_subdev *sd)
>> +{
>> + return container_of(sd, struct mipid02_dev, sd);
>> +}
>> +
>> +static int mipid02_read_reg(struct mipid02_dev *bridge, u16 reg, u8 *val)
>> +{
>> + struct i2c_client *client = bridge->i2c_client;
>> + struct i2c_msg msg[2];
>> + u8 buf[2];
>> + int ret;
>> +
>> + buf[0] = reg >> 8;
>> + buf[1] = reg & 0xff;
>> +
>> + msg[0].addr = client->addr;
>> + msg[0].flags = client->flags;
>> + msg[0].buf = buf;
>> + msg[0].len = sizeof(buf);
>> +
>> + msg[1].addr = client->addr;
>> + msg[1].flags = client->flags | I2C_M_RD;
>> + msg[1].buf = val;
>> + msg[1].len = 1;
>> +
>> + ret = i2c_transfer(client->adapter, msg, 2);
>> + if (ret < 0) {
>> + dev_dbg(&client->dev, "%s: %x i2c_transfer, reg: %x => %d\n",
>> + __func__, client->addr, reg, ret);
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int mipid02_write_reg(struct mipid02_dev *bridge, u16 reg, u8 val)
>> +{
>> + struct i2c_client *client = bridge->i2c_client;
>> + struct i2c_msg msg;
>> + u8 buf[3];
>> + int ret;
>> +
>> + buf[0] = reg >> 8;
>> + buf[1] = reg & 0xff;
>> + buf[2] = val;
>> +
>> + msg.addr = client->addr;
>> + msg.flags = client->flags;
>> + msg.buf = buf;
>> + msg.len = sizeof(buf);
>> +
>> + ret = i2c_transfer(client->adapter, &msg, 1);
>> + if (ret < 0) {
>> + dev_dbg(&client->dev, "%s: i2c_transfer, reg: %x => %d\n",
>> + __func__, reg, ret);
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int mipid02_get_regulators(struct mipid02_dev *bridge)
>> +{
>> + unsigned int i;
>> +
>> + for (i = 0; i < MIPID02_NUM_SUPPLIES; i++)
>> + bridge->supplies[i].supply = mipid02_supply_name[i];
>> +
>> + return devm_regulator_bulk_get(&bridge->i2c_client->dev,
>> + MIPID02_NUM_SUPPLIES,
>> + bridge->supplies);
>> +}
>> +
>> +static void mipid02_apply_reset(struct mipid02_dev *bridge)
>> +{
>> + gpiod_set_value_cansleep(bridge->reset_gpio, 0);
>> + usleep_range(5000, 10000);
>> + gpiod_set_value_cansleep(bridge->reset_gpio, 1);
>> + usleep_range(5000, 10000);
>> + gpiod_set_value_cansleep(bridge->reset_gpio, 0);
>> + usleep_range(5000, 10000);
>> +}
>> +
>> +static int mipid02_set_power_on(struct mipid02_dev *bridge)
>> +{
>> + struct i2c_client *client = bridge->i2c_client;
>> + int ret;
>> +
>> + ret = clk_prepare_enable(bridge->xclk);
>> + if (ret) {
>> + dev_err(&client->dev, "%s: failed to enable clock\n", __func__);
>> + return ret;
>> + }
>> +
>> + ret = regulator_bulk_enable(MIPID02_NUM_SUPPLIES,
>> + bridge->supplies);
>> + if (ret) {
>> + dev_err(&client->dev, "%s: failed to enable regulators\n",
>> + __func__);
>> + goto xclk_off;
>> + }
>> +
>> + if (bridge->reset_gpio) {
>> + dev_dbg(&client->dev, "apply reset");
>> + mipid02_apply_reset(bridge);
>> + } else {
>> + dev_dbg(&client->dev, "don't apply reset");
>> + usleep_range(5000, 10000);
>> + }
>> +
>> + return 0;
>> +
>> +xclk_off:
>> + clk_disable_unprepare(bridge->xclk);
>> + return ret;
>> +}
>> +
>> +static void mipid02_set_power_off(struct mipid02_dev *bridge)
>> +{
>> + regulator_bulk_disable(MIPID02_NUM_SUPPLIES, bridge->supplies);
>> + clk_disable_unprepare(bridge->xclk);
>> +}
>> +
>> +static int mipid02_detect(struct mipid02_dev *bridge)
>> +{
>> + u8 reg;
>> +
>> + /*
>> + * There is no version registers. Just try to read register
>> + * MIPID02_CLK_LANE_WR_REG1.
>> + */
>> + return mipid02_read_reg(bridge, MIPID02_CLK_LANE_WR_REG1, ®);
>> +}
>> +
>> +static u32 mipid02_get_link_freq_from_cid_pixel_rate(struct mipid02_dev *bridge,
>> + struct v4l2_subdev *subdev)
>> +{
>> + struct v4l2_fwnode_endpoint *ep = &bridge->rx;
>> + struct v4l2_ctrl *ctrl;
>> + u32 pixel_clock;
>> + u32 bpp = bpp_from_code(bridge->fmt.code);
>> +
>> + ctrl = v4l2_ctrl_find(subdev->ctrl_handler, V4L2_CID_PIXEL_RATE);
>> + if (!ctrl)
>> + return 0;
>> + pixel_clock = v4l2_ctrl_g_ctrl_int64(ctrl);
>> +
>> + return pixel_clock * bpp / (2 * ep->bus.mipi_csi2.num_data_lanes);
>> +}
>> +
>> +/*
>> + * We need to know link frequency to setup clk_lane_reg1 timings. Link frequency
>> + * will be computed using connected device V4L2_CID_PIXEL_RATE, bit per pixel
>> + * and number of lanes.
>> + */
>> +static int mipid02_configure_from_rx_speed(struct mipid02_dev *bridge)
>> +{
>> + struct i2c_client *client = bridge->i2c_client;
>> + struct v4l2_subdev *subdev = bridge->s_subdev;
>> + u32 link_freq;
>> +
>> + link_freq = mipid02_get_link_freq_from_cid_pixel_rate(bridge, subdev);
>> + if (!link_freq) {
>> + dev_err(&client->dev, "Failed to detect link frequency");
>> + return -EINVAL;
>> + }
>> +
>> + dev_dbg(&client->dev, "detect link_freq = %d Hz", link_freq);
>> + bridge->r.clk_lane_reg1 |= (2000000000 / link_freq) << 2;
>> +
>> + return 0;
>> +}
>> +
>> +static int mipid02_configure_clk_lane(struct mipid02_dev *bridge)
>> +{
>> + struct i2c_client *client = bridge->i2c_client;
>> + struct v4l2_fwnode_endpoint *ep = &bridge->rx;
>> + bool *polarities = ep->bus.mipi_csi2.lane_polarities;
>> +
>> + /* midid02 doesn't support clock lane remapping */
>> + if (ep->bus.mipi_csi2.clock_lane != 0) {
>> + dev_err(&client->dev, "clk lane must be map to lane 0\n");
>> + return -EINVAL;
>> + }
>> + bridge->r.clk_lane_reg1 |= (polarities[0] << 1) | CLK_ENABLE;
>> +
>> + return 0;
>> +}
>> +
>> +static int mipid02_configure_data0_lane(struct mipid02_dev *bridge, int nb,
>> + bool are_lanes_swap, bool *polarities)
>> +{
>> + bool are_pin_swap = are_lanes_swap ? polarities[2] : polarities[1];
>> +
>> + if (nb == 1 && are_lanes_swap)
>> + return 0;
>> +
>> + /*
>> + * data lane 0 as pin swap polarity reversed compared to clock and
>> + * data lane 1
>> + */
>> + if (!are_pin_swap)
>> + bridge->r.data_lane0_reg1 = 1 << 1;
>> + bridge->r.data_lane0_reg1 |= DATA_ENABLE;
>> +
>> + return 0;
>> +}
>> +
>> +static int mipid02_configure_data1_lane(struct mipid02_dev *bridge, int nb,
>> + bool are_lanes_swap, bool *polarities)
>> +{
>> + bool are_pin_swap = are_lanes_swap ? polarities[1] : polarities[2];
>> +
>> + if (nb == 1 && !are_lanes_swap)
>> + return 0;
>> +
>> + if (are_pin_swap)
>> + bridge->r.data_lane1_reg1 = 1 << 1;
>> + bridge->r.data_lane1_reg1 |= DATA_ENABLE;
>> +
>> + return 0;
>> +}
>> +
>> +static int mipid02_configure_from_rx(struct mipid02_dev *bridge)
>> +{
>> + struct v4l2_fwnode_endpoint *ep = &bridge->rx;
>> + bool are_lanes_swap = ep->bus.mipi_csi2.data_lanes[0] == 2;
>> + bool *polarities = ep->bus.mipi_csi2.lane_polarities;
>> + int nb = ep->bus.mipi_csi2.num_data_lanes;
>> + int ret;
>> +
>> + ret = mipid02_configure_clk_lane(bridge);
>> + if (ret)
>> + return ret;
>> +
>> + ret = mipid02_configure_data0_lane(bridge, nb, are_lanes_swap,
>> + polarities);
>> + if (ret)
>> + return ret;
>> +
>> + ret = mipid02_configure_data1_lane(bridge, nb, are_lanes_swap,
>> + polarities);
>> + if (ret)
>> + return ret;
>> +
>> + bridge->r.mode_reg1 |= are_lanes_swap ? MODE_DATA_SWAP : 0;
>> + bridge->r.mode_reg1 |= (nb - 1) << 1;
>> +
>> + return mipid02_configure_from_rx_speed(bridge);
>> +}
>> +
>> +static int mipid02_configure_from_tx(struct mipid02_dev *bridge)
>> +{
>> + struct v4l2_fwnode_endpoint *ep = &bridge->tx;
>> +
>> + bridge->r.pix_width_ctrl = ep->bus.parallel.bus_width;
>> + bridge->r.pix_width_ctrl_emb = ep->bus.parallel.bus_width;
>> + if (ep->bus.parallel.flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
>> + bridge->r.mode_reg2 |= MODE_HSYNC_ACTIVE_HIGH;
>> + if (ep->bus.parallel.flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH)
>> + bridge->r.mode_reg2 |= MODE_VSYNC_ACTIVE_HIGH;
>> +
>> + return 0;
>> +}
>> +
>> +static int mipid02_configure_from_code(struct mipid02_dev *bridge)
>> +{
>> + u8 data_type;
>> +
>> + bridge->r.data_id_rreg = 0;
>> + data_type = data_type_from_code(bridge->fmt.code);
>> + if (!data_type)
>> + return -EINVAL;
>> + bridge->r.data_id_rreg = data_type;
>> +
>> + return 0;
>> +}
>> +
>> +static int mipid02_stream_disable(struct mipid02_dev *bridge)
>> +{
>> + struct i2c_client *client = bridge->i2c_client;
>> + int ret;
>> +
>> + /* Disable all lanes */
>> + ret = mipid02_write_reg(bridge, MIPID02_CLK_LANE_REG1, 0);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE0_REG1, 0);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE1_REG1, 0);
>> + if (ret)
>> + goto error;
>> +error:
>> + if (ret)
>> + dev_err(&client->dev, "failed to stream off %d", ret);
>> +
>> + return ret;
>> +}
>> +
>> +static int mipid02_stream_enable(struct mipid02_dev *bridge)
>> +{
>> + struct i2c_client *client = bridge->i2c_client;
>> + int ret = -EINVAL;
>> +
>> + if (!bridge->s_subdev)
>> + goto error;
>> +
>> + memset(&bridge->r, 0, sizeof(bridge->r));
>> + /* build registers content */
>> + ret = mipid02_configure_from_rx(bridge);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_configure_from_tx(bridge);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_configure_from_code(bridge);
>> + if (ret)
>> + goto error;
>> +
>> + /* write mipi registers */
>> + ret = mipid02_write_reg(bridge, MIPID02_CLK_LANE_REG1,
>> + bridge->r.clk_lane_reg1);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_CLK_LANE_REG3, CLK_MIPI_CSI);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE0_REG1,
>> + bridge->r.data_lane0_reg1);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE0_REG2,
>> + DATA_MIPI_CSI);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE1_REG1,
>> + bridge->r.data_lane1_reg1);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE1_REG2,
>> + DATA_MIPI_CSI);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_MODE_REG1,
>> + MODE_NO_BYPASS | bridge->r.mode_reg1);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_MODE_REG2,
>> + bridge->r.mode_reg2);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_DATA_ID_RREG,
>> + bridge->r.data_id_rreg);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_DATA_SELECTION_CTRL,
>> + SELECTION_MANUAL_DATA | SELECTION_MANUAL_WIDTH);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_PIX_WIDTH_CTRL,
>> + bridge->r.pix_width_ctrl);
>> + if (ret)
>> + goto error;
>> + ret = mipid02_write_reg(bridge, MIPID02_PIX_WIDTH_CTRL_EMB,
>> + bridge->r.pix_width_ctrl_emb);
>> + if (ret)
>> + goto error;
>> +
>> + return 0;
>> +
>> +error:
>> + dev_err(&client->dev, "failed to stream on %d", ret);
>> + mipid02_stream_disable(bridge);
>> +
>> + return ret;
>> +}
>> +
>> +static int mipid02_s_stream(struct v4l2_subdev *sd, int enable)
>> +{
>> + struct mipid02_dev *bridge = to_mipid02_dev(sd);
>> + struct i2c_client *client = bridge->i2c_client;
>> + int ret = 0;
>> +
>> + dev_dbg(&client->dev, "%s : requested %d / current = %d", __func__,
>> + enable, bridge->streaming);
>> + mutex_lock(&bridge->lock);
>> +
>> + if (bridge->streaming == enable)
>> + goto out;
>> +
>> + ret = enable ? mipid02_stream_enable(bridge) :
>> + mipid02_stream_disable(bridge);
>> + if (!ret)
>> + bridge->streaming = enable;
>> +
>> +out:
>> + dev_dbg(&client->dev, "%s current now = %d / %d", __func__,
>> + bridge->streaming, ret);
>> + mutex_unlock(&bridge->lock);
>> +
>> + return ret;
>> +}
>> +
>> +static int mipid02_enum_mbus_code(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_pad_config *cfg,
>> + struct v4l2_subdev_mbus_code_enum *code)
>> +{
>> + struct mipid02_dev *bridge = to_mipid02_dev(sd);
>> + int ret = 0;
>> +
>> + switch (code->pad) {
>> + case MIPID02_SINK_0:
>> + if (code->index >= ARRAY_SIZE(mipid02_supported_fmt_codes))
>> + ret = -EINVAL;
>> + else
>> + code->code = mipid02_supported_fmt_codes[code->index];
>> + break;
>> + case MIPID02_SOURCE:
>> + if (code->index == 0)
>> + code->code = serial_to_parallel_code(bridge->fmt.code);
>> + else
>> + ret = -EINVAL;
>> + break;
>> + default:
>> + ret = -EINVAL;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static int mipid02_get_fmt(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_pad_config *cfg,
>> + struct v4l2_subdev_format *format)
>> +{
>> + struct v4l2_mbus_framefmt *mbus_fmt = &format->format;
>> + struct mipid02_dev *bridge = to_mipid02_dev(sd);
>> + struct i2c_client *client = bridge->i2c_client;
>> + struct v4l2_mbus_framefmt *fmt;
>> +
>> + dev_dbg(&client->dev, "%s probe %d", __func__, format->pad);
>> +
>> + if (format->pad >= MIPID02_PAD_NB)
>> + return -EINVAL;
>> + /* second CSI-2 pad not yet supported */
>> + if (format->pad == MIPID02_SINK_1)
>> + return -EINVAL;
>> +
>> + if (format->which == V4L2_SUBDEV_FORMAT_TRY)
>> + fmt = v4l2_subdev_get_try_format(&bridge->sd, cfg, format->pad);
>> + else
>> + fmt = &bridge->fmt;
>> +
>> + mutex_lock(&bridge->lock);
>> +
>> + *mbus_fmt = *fmt;
>> + /* code may need to be converted for source */
>> + if (format->pad == MIPID02_SOURCE)
>> + mbus_fmt->code = serial_to_parallel_code(mbus_fmt->code);
>> +
>> + mutex_unlock(&bridge->lock);
>> +
>> + return 0;
>> +}
>> +
>> +static void mipid02_set_fmt_source(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_pad_config *cfg,
>> + struct v4l2_subdev_format *format)
>> +{
>> + struct mipid02_dev *bridge = to_mipid02_dev(sd);
>> +
>> + /* source pad mirror active sink pad */
>> + format->format = bridge->fmt;
>> + /* but code may need to be converted */
>> + format->format.code = serial_to_parallel_code(format->format.code);
>> +
>> + /* only apply format for V4L2_SUBDEV_FORMAT_TRY case */
>> + if (format->which != V4L2_SUBDEV_FORMAT_TRY)
>> + return;
>> +
>> + *v4l2_subdev_get_try_format(sd, cfg, format->pad) = format->format;
>> +}
>> +
>> +static void mipid02_set_fmt_sink(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_pad_config *cfg,
>> + struct v4l2_subdev_format *format)
>> +{
>> + struct mipid02_dev *bridge = to_mipid02_dev(sd);
>> + struct v4l2_mbus_framefmt *fmt;
>> +
>> + format->format.code = get_fmt_code(format->format.code);
>> +
>> + if (format->which == V4L2_SUBDEV_FORMAT_TRY)
>> + fmt = v4l2_subdev_get_try_format(sd, cfg, format->pad);
>> + else
>> + fmt = &bridge->fmt;
>> +
>> + *fmt = format->format;
>> +}
>> +
>> +static int mipid02_set_fmt(struct v4l2_subdev *sd,
>> + struct v4l2_subdev_pad_config *cfg,
>> + struct v4l2_subdev_format *format)
>> +{
>> + struct mipid02_dev *bridge = to_mipid02_dev(sd);
>> + struct i2c_client *client = bridge->i2c_client;
>> + int ret = 0;
>> +
>> + dev_dbg(&client->dev, "%s for %d", __func__, format->pad);
>> +
>> + if (format->pad >= MIPID02_PAD_NB)
>> + return -EINVAL;
>> + /* second CSI-2 pad not yet supported */
>> + if (format->pad == MIPID02_SINK_1)
>> + return -EINVAL;
>> +
>> + mutex_lock(&bridge->lock);
>> +
>> + if (bridge->streaming) {
>> + ret = -EBUSY;
>> + goto error;
>> + }
>> +
>> + if (format->pad == MIPID02_SOURCE)
>> + mipid02_set_fmt_source(sd, cfg, format);
>> + else
>> + mipid02_set_fmt_sink(sd, cfg, format);
>> +
>> +error:
>> + mutex_unlock(&bridge->lock);
>> +
>> + return ret;
>> +}
>> +
>> +static const struct v4l2_subdev_video_ops mipid02_video_ops = {
>> + .s_stream = mipid02_s_stream,
>> +};
>> +
>> +static const struct v4l2_subdev_pad_ops mipid02_pad_ops = {
>> + .enum_mbus_code = mipid02_enum_mbus_code,
>> + .get_fmt = mipid02_get_fmt,
>> + .set_fmt = mipid02_set_fmt,
>> +};
>> +
>> +static const struct v4l2_subdev_ops mipid02_subdev_ops = {
>> + .video = &mipid02_video_ops,
>> + .pad = &mipid02_pad_ops,
>> +};
>> +
>> +static const struct media_entity_operations mipid02_subdev_entity_ops = {
>> + .link_validate = v4l2_subdev_link_validate,
>> +};
>> +
>> +static int mipid02_async_bound(struct v4l2_async_notifier *notifier,
>> + struct v4l2_subdev *s_subdev,
>> + struct v4l2_async_subdev *asd)
>> +{
>> + struct mipid02_dev *bridge = to_mipid02_dev(notifier->sd);
>> + struct i2c_client *client = bridge->i2c_client;
>> + int source_pad;
>> + int ret;
>> +
>> + dev_dbg(&client->dev, "sensor_async_bound call %p", s_subdev);
>> +
>> + source_pad = media_entity_get_fwnode_pad(&s_subdev->entity,
>> + s_subdev->fwnode,
>> + MEDIA_PAD_FL_SOURCE);
>> + if (source_pad < 0) {
>> + dev_err(&client->dev, "Couldn't find output pad for subdev %s\n",
>> + s_subdev->name);
>> + return source_pad;
>> + }
>> +
>> + ret = media_create_pad_link(&s_subdev->entity, source_pad,
>> + &bridge->sd.entity, 0,
>> + MEDIA_LNK_FL_ENABLED |
>> + MEDIA_LNK_FL_IMMUTABLE);
>> + if (ret) {
>> + dev_err(&client->dev, "Couldn't create media link %d", ret);
>> + return ret;
>> + }
>> +
>> + bridge->s_subdev = s_subdev;
>> +
>> + return 0;
>> +}
>> +
>> +static void mipid02_async_unbind(struct v4l2_async_notifier *notifier,
>> + struct v4l2_subdev *s_subdev,
>> + struct v4l2_async_subdev *asd)
>> +{
>> + struct mipid02_dev *bridge = to_mipid02_dev(notifier->sd);
>> +
>> + bridge->s_subdev = NULL;
>> +}
>> +
>> +static const struct v4l2_async_notifier_operations mipid02_notifier_ops = {
>> + .bound = mipid02_async_bound,
>> + .unbind = mipid02_async_unbind,
>> +};
>> +
>> +static int mipid02_parse_rx_ep(struct mipid02_dev *bridge)
>> +{
>> + struct v4l2_fwnode_endpoint ep = { .bus_type = V4L2_MBUS_CSI2_DPHY };
>> + struct i2c_client *client = bridge->i2c_client;
>> + struct device_node *ep_node;
>> + int ret;
>> +
>> + /* parse rx (endpoint 0) */
>> + ep_node = of_graph_get_endpoint_by_regs(bridge->i2c_client->dev.of_node,
>> + 0, 0);
>> + if (!ep_node) {
>> + dev_err(&client->dev, "unable to find port0 ep");
>> + ret = -EINVAL;
>> + goto error;
>> + }
>> +
>> + ret = v4l2_fwnode_endpoint_alloc_parse(of_fwnode_handle(ep_node), &ep);
>> + if (ret) {
>> + dev_err(&client->dev, "Could not parse v4l2 endpoint %d\n",
>> + ret);
>> + goto error_of_node_put;
>> + }
>> +
>> + /* do some sanity checks */
>> + if (ep.bus.mipi_csi2.num_data_lanes > 2) {
>> + dev_err(&client->dev, "max supported data lanes is 2 / got %d",
>> + ep.bus.mipi_csi2.num_data_lanes);
>> + ret = -EINVAL;
>> + goto error_v4l2_fwnode_endpoint_free;
>> + }
>> +
>> + /* register it for later use */
>> + bridge->rx = ep;
>> + v4l2_fwnode_endpoint_free(&ep);
>
> As you don't use variable size properties, you could use
> v4l2_fwnode_endpoint_parse() instead. The note in
> v4l2_fwnode_endpoint_parse() telling to use
> v4l2_fwnode_endpoint_alloc_parse() in new drivers isn't actully entirely
> correct; the old function is just fine if you don't need any variable size
> properties. I'll submit a patch to change that.
>
Ok. I forgot to change it when I remove link_frequencies usage.
>> +
>> + /* register async notifier so we get noticed when sensor is connected */
>> + bridge->asd.match.fwnode =
>> + fwnode_graph_get_remote_port_parent(of_fwnode_handle(ep_node));
>> + bridge->asd.match_type = V4L2_ASYNC_MATCH_FWNODE;
>> + of_node_put(ep_node);
>> +
>> + v4l2_async_notifier_init(&bridge->notifier);
>> + ret = v4l2_async_notifier_add_subdev(&bridge->notifier, &bridge->asd);
>> + if (ret) {
>> + dev_err(&client->dev, "fail to register asd to notifier %d",
>> + ret);
>> + goto error_fwnode_handle_put;
>> + }
>> + bridge->notifier.ops = &mipid02_notifier_ops;
>> +
>> + ret = v4l2_async_subdev_notifier_register(&bridge->sd,
>> + &bridge->notifier);
>> + if (ret)
>> + v4l2_async_notifier_cleanup(&bridge->notifier);
>> +
>> + return ret;
>> +
>> +error_v4l2_fwnode_endpoint_free:
>> + v4l2_fwnode_endpoint_free(&ep);
>> +error_of_node_put:
>> + of_node_put(ep_node);
>> +error:
>> +
>> + return ret;
>> +
>> +error_fwnode_handle_put:
>> + fwnode_handle_put(bridge->asd.match.fwnode);
>
> You only go here once; please drop the label and goto and move the code
> where it's used.
>
Ok
>> +
>> + return ret;
>> +}
>> +
>> +static int mipid02_parse_tx_ep(struct mipid02_dev *bridge)
>> +{
>> + struct v4l2_fwnode_endpoint ep = { .bus_type = V4L2_MBUS_PARALLEL };
>> + struct i2c_client *client = bridge->i2c_client;
>> + struct device_node *ep_node;
>> + int ret;
>> +
>> + /* parse tx (endpoint 2) */
>> + ep_node = of_graph_get_endpoint_by_regs(bridge->i2c_client->dev.of_node,
>> + 2, 0);
>> + if (!ep_node) {
>> + dev_err(&client->dev, "unable to find port1 ep");
>> + ret = -EINVAL;
>> + goto error;
>> + }
>> +
>> + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_node), &ep);
>> + if (ret) {
>> + dev_err(&client->dev, "Could not parse v4l2 endpoint\n");
>> + goto error_of_node_put;
>> + }
>> +
>> + of_node_put(ep_node);
>> + bridge->tx = ep;
>> +
>> + return 0;
>> +
>> +error_of_node_put:
>> + of_node_put(ep_node);
>> +error:
>> +
>> + return -EINVAL;
>> +}
>> +
>> +static int mipid02_probe(struct i2c_client *client,
>> + const struct i2c_device_id *id)
>> +{
>> + struct device *dev = &client->dev;
>> + struct mipid02_dev *bridge;
>> + u32 clk_freq;
>> + int ret;
>> +
>> + bridge = devm_kzalloc(dev, sizeof(*bridge), GFP_KERNEL);
>> + if (!bridge)
>> + return -ENOMEM;
>> +
>> + init_format(&bridge->fmt);
>> +
>> + bridge->i2c_client = client;
>> + v4l2_i2c_subdev_init(&bridge->sd, client, &mipid02_subdev_ops);
>> +
>> + /* got and check clock */
>> + bridge->xclk = devm_clk_get(dev, "xclk");
>> + if (IS_ERR(bridge->xclk)) {
>> + dev_err(dev, "failed to get xclk\n");
>> + return PTR_ERR(bridge->xclk);
>> + }
>> +
>> + clk_freq = clk_get_rate(bridge->xclk);
>> + if (clk_freq < 6000000 || clk_freq > 27000000) {
>> + dev_err(dev, "xclk freq must be in 6-27 Mhz range. got %d Hz\n",
>> + clk_freq);
>> + return -EINVAL;
>> + }
>> +
>> + bridge->reset_gpio = devm_gpiod_get_optional(dev, "reset",
>> + GPIOD_OUT_HIGH);
>> +
>> + ret = mipid02_get_regulators(bridge);
>> + if (ret) {
>> + dev_err(dev, "failed to get regulators %d", ret);
>> + return ret;
>> + }
>> +
>> + mutex_init(&bridge->lock);
>> + bridge->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
>> + bridge->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
>> + bridge->sd.entity.ops = &mipid02_subdev_entity_ops;
>> + bridge->pad[0].flags = MEDIA_PAD_FL_SINK;
>> + bridge->pad[1].flags = MEDIA_PAD_FL_SINK;
>> + bridge->pad[2].flags = MEDIA_PAD_FL_SOURCE;
>> + ret = media_entity_pads_init(&bridge->sd.entity, MIPID02_PAD_NB,
>> + bridge->pad);
>> + if (ret) {
>> + dev_err(&client->dev, "pads init failed %d", ret);
>
> mutex_destroy(&bridge->lock);
>
> Please add a label and change return to goto below.
>
Ok. I missed mutex_destroy ...
>> + return ret;
>> + }
>> +
>> + /* enable clock, power and reset device if available */
>> + ret = mipid02_set_power_on(bridge);
>> + if (ret)
>> + goto entity_cleanup;
>> +
>> + ret = mipid02_detect(bridge);
>> + if (ret) {
>> + dev_err(&client->dev, "failed to detect mipid02 %d", ret);
>> + goto power_off;
>> + }
>> +
>> + ret = mipid02_parse_tx_ep(bridge);
>> + if (ret) {
>> + dev_err(&client->dev, "failed to parse tx %d", ret);
>> + goto power_off;
>> + }
>> +
>> + ret = mipid02_parse_rx_ep(bridge);
>> + if (ret) {
>> + dev_err(&client->dev, "failed to parse rx %d", ret);
>> + goto power_off;
>> + }
>> +
>> + ret = v4l2_async_register_subdev(&bridge->sd);
>> + if (ret < 0) {
>> + dev_err(&client->dev, "v4l2_async_register_subdev failed %d",
>> + ret);
>> + goto unregister_notifier;
>> + }
>> +
>> + dev_info(&client->dev, "mipid02 device probe successfully");
>> +
>> + return 0;
>> +
>> +unregister_notifier:
>> + v4l2_async_notifier_unregister(&bridge->notifier);
>> + v4l2_async_notifier_cleanup(&bridge->notifier);
>> +power_off:
>> + mipid02_set_power_off(bridge);
>> +entity_cleanup:
>> + media_entity_cleanup(&bridge->sd.entity);
>> +
>> + return ret;
>> +}
>> +
>> +static int mipid02_remove(struct i2c_client *client)
>> +{
>> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
>> + struct mipid02_dev *bridge = to_mipid02_dev(sd);
>> +
>> + v4l2_async_notifier_unregister(&bridge->notifier);
>> + v4l2_async_notifier_cleanup(&bridge->notifier);
>> + v4l2_async_unregister_subdev(&bridge->sd);
>> + mipid02_set_power_off(bridge);
>> + media_entity_cleanup(&bridge->sd.entity);
>
> mutex_destroy(&bridge->lock);
>
Ok
>> +
>> + return 0;
>> +}
>> +
>> +static const struct i2c_device_id mipid02_id[] = {
>> + { "st-mipid02", 0},
>> + {},
>> +};
>> +MODULE_DEVICE_TABLE(i2c, mipid02_id);
>> +
>> +static const struct of_device_id mipid02_dt_ids[] = {
>> + { .compatible = "st,st-mipid02" },
>> + { /* sentinel */ }
>> +};
>> +MODULE_DEVICE_TABLE(of, mipid02_dt_ids);
>> +
>> +static struct i2c_driver mipid02_i2c_driver = {
>> + .driver = {
>> + .name = "st-mipid02",
>> + .of_match_table = mipid02_dt_ids,
>> + },
>> + .id_table = mipid02_id,
>> + .probe = mipid02_probe,
>
> Probe_new, and you can omit the I²C ID table. Unless it's needed, of
> course, but generally it isn't.
It isn't need. I will switch to probe_new.
> The above are just minor improvements and cleanups. If you're fine with the
> proposed change to the first patch, I can merge this version of the patches
> and you could submit changes to the above in a separate patch.
>
Thanks for the proposal, but I prefer to to a full v5 if you agree ?
I will also add MEDIA_BUS_FMT_BGR888_3X8 or MEDIA_BUS_FMT_BGR888_3X8_BE
support.
>> + .remove = mipid02_remove,
>> +};
>> +
>> +module_i2c_driver(mipid02_i2c_driver);
>> +
>> +MODULE_AUTHOR("Mickael Guene <mickael.guene@...com>");
>> +MODULE_DESCRIPTION("STMicroelectronics MIPID02 CSI-2 bridge driver");
>> +MODULE_LICENSE("GPL v2");
>
Powered by blists - more mailing lists