| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1556876854-32441-1-git-send-email-alexandre.torgue@st.com>
Date: Fri, 3 May 2019 11:47:34 +0200
From: Alexandre Torgue <alexandre.torgue@...com>
To: Maxime Coquelin <mcoquelin.stm32@...il.com>,
Linus Walleij <linus.walleij@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>
CC: <linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<linux-gpio@...r.kernel.org>,
<linux-stm32@...md-mailman.stormreply.com>,
Alexandre Torgue <alexandre.torgue@...com>
Subject: [PATCH] dt-bindings: pinctrl: Convert stm32 pinctrl bindings to jason-schema
Convert the STM32 pinctrl binding to DT schema format using json-schema.
Signed-off-by: Alexandre Torgue <alexandre.torgue@...com>
---
Hi,
First pacth to convert DT bindings file (here pinctrl STM32) to jsaon-schema
in order to take advantage of devicetree validation tool for STM32.
regards
Alex
diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
deleted file mode 100644
index 0016925..0000000
--- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
+++ /dev/null
@@ -1,208 +0,0 @@
-* STM32 GPIO and Pin Mux/Config controller
-
-STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware
-controller. It controls the input/output settings on the available pins and
-also provides ability to multiplex and configure the output of various on-chip
-controllers onto these pads.
-
-Pin controller node:
-Required properies:
- - compatible: value should be one of the following:
- "st,stm32f429-pinctrl"
- "st,stm32f469-pinctrl"
- "st,stm32f746-pinctrl"
- "st,stm32f769-pinctrl"
- "st,stm32h743-pinctrl"
- "st,stm32mp157-pinctrl"
- "st,stm32mp157-z-pinctrl"
- - #address-cells: The value of this property must be 1
- - #size-cells : The value of this property must be 1
- - ranges : defines mapping between pin controller node (parent) to
- gpio-bank node (children).
- - pins-are-numbered: Specify the subnodes are using numbered pinmux to
- specify pins.
-
-GPIO controller/bank node:
-Required properties:
- - gpio-controller : Indicates this device is a GPIO controller
- - #gpio-cells : Should be two.
- The first cell is the pin number
- The second one is the polarity:
- - 0 for active high
- - 1 for active low
- - reg : The gpio address range, relative to the pinctrl range
- - clocks : clock that drives this bank
- - st,bank-name : Should be a name string for this bank as specified in
- the datasheet
-
-Optional properties:
- - reset: : Reference to the reset controller
- - st,syscfg: Should be phandle/offset/mask.
- -The phandle to the syscon node which includes IRQ mux selection register.
- -The offset of the IRQ mux selection register
- -The field mask of IRQ mux, needed if different of 0xf.
- - gpio-ranges: Define a dedicated mapping between a pin-controller and
- a gpio controller. Format is <&phandle a b c> with:
- -(phandle): phandle of pin-controller.
- -(a): gpio base offset in range.
- -(b): pin base offset in range.
- -(c): gpio count in range
- This entry has to be used either if there are holes inside a bank:
- GPIOB0/B1/B2/B14/B15 (see example 2)
- or if banks are not contiguous:
- GPIOA/B/C/E...
- NOTE: If "gpio-ranges" is used for a gpio controller, all gpio-controller
- have to use a "gpio-ranges" entry.
- More details in Documentation/devicetree/bindings/gpio/gpio.txt.
- - st,bank-ioport: should correspond to the EXTI IOport selection (EXTI line
- used to select GPIOs as interrupts).
- - hwlocks: reference to a phandle of a hardware spinlock provider node.
- - st,package: Indicates the SOC package used.
- More details in include/dt-bindings/pinctrl/stm32-pinfunc.h
-
-Example 1:
-#include <dt-bindings/pinctrl/stm32f429-pinfunc.h>
-...
-
- pin-controller {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "st,stm32f429-pinctrl";
- ranges = <0 0x40020000 0x3000>;
- pins-are-numbered;
-
- gpioa: gpio@...20000 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x0 0x400>;
- resets = <&reset_ahb1 0>;
- st,bank-name = "GPIOA";
- };
- ...
- pin-functions nodes follow...
- };
-
-Example 2:
-#include <dt-bindings/pinctrl/stm32f429-pinfunc.h>
-...
-
- pinctrl: pin-controller {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "st,stm32f429-pinctrl";
- ranges = <0 0x40020000 0x3000>;
- pins-are-numbered;
-
- gpioa: gpio@...20000 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x0 0x400>;
- resets = <&reset_ahb1 0>;
- st,bank-name = "GPIOA";
- gpio-ranges = <&pinctrl 0 0 16>;
- };
-
- gpiob: gpio@...20400 {
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x0 0x400>;
- resets = <&reset_ahb1 0>;
- st,bank-name = "GPIOB";
- ngpios = 4;
- gpio-ranges = <&pinctrl 0 16 3>,
- <&pinctrl 14 30 2>;
- };
-
-
- ...
- pin-functions nodes follow...
- };
-
-
-Contents of function subnode node:
-----------------------------------
-Subnode format
-A pinctrl node should contain at least one subnode representing the
-pinctrl group available on the machine. Each subnode will list the
-pins it needs, and how they should be configured, with regard to muxer
-configuration, pullups, drive, output high/low and output speed.
-
- node {
- pinmux = <PIN_NUMBER_PINMUX>;
- GENERIC_PINCONFIG;
- };
-
-Required properties:
-- pinmux: integer array, represents gpio pin number and mux setting.
- Supported pin number and mux varies for different SoCs, and are defined in
- dt-bindings/pinctrl/<soc>-pinfunc.h directly.
- These defines are calculated as:
- ((port * 16 + line) << 8) | function
- With:
- - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11)
- - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15)
- - function: The function number, can be:
- * 0 : GPIO
- * 1 : Alternate Function 0
- * 2 : Alternate Function 1
- * 3 : Alternate Function 2
- * ...
- * 16 : Alternate Function 15
- * 17 : Analog
-
- To simplify the usage, macro is available to generate "pinmux" field.
- This macro is available here:
- - include/dt-bindings/pinctrl/stm32-pinfunc.h
-
- Some examples of using macro:
- /* GPIO A9 set as alernate function 2 */
- ... {
- pinmux = <STM32_PINMUX('A', 9, AF2)>;
- };
- /* GPIO A9 set as GPIO */
- ... {
- pinmux = <STM32_PINMUX('A', 9, GPIO)>;
- };
- /* GPIO A9 set as analog */
- ... {
- pinmux = <STM32_PINMUX('A', 9, ANALOG)>;
- };
-
-Optional properties:
-- GENERIC_PINCONFIG: is the generic pinconfig options to use.
- Available options are:
- - bias-disable,
- - bias-pull-down,
- - bias-pull-up,
- - drive-push-pull,
- - drive-open-drain,
- - output-low
- - output-high
- - slew-rate = <x>, with x being:
- < 0 > : Low speed
- < 1 > : Medium speed
- < 2 > : Fast speed
- < 3 > : High speed
-
-Example:
-
-pin-controller {
-...
- usart1_pins_a: usart1@0 {
- pins1 {
- pinmux = <STM32_PINMUX('A', 9, AF7)>;
- bias-disable;
- drive-push-pull;
- slew-rate = <0>;
- };
- pins2 {
- pinmux = <STM32_PINMUX('A', 10, AF7)>;
- bias-disable;
- };
- };
-};
-
-&usart1 {
- pinctrl-0 = <&usart1_pins_a>;
- pinctrl-names = "default";
-};
diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml
new file mode 100644
index 0000000..fcceca0
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml
@@ -0,0 +1,271 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (C) STMicroelectronics 2019.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/st,stm32-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STM32 GPIO and Pin Mux/Config controller
+
+maintainers:
+ - Alexandre TORGUE <alexandre.torgue@...com>
+description: |
+ STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware
+ controller. It controls the input/output settings on the available pins and
+ also provides ability to multiplex and configure the output of various
+ on-chip controllers onto these pads.
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - st,stm32f429-pinctrl
+ - st,stm32f469-pinctrl
+ - st,stm32f746-pinctrl
+ - st,stm32f769-pinctrl
+ - st,stm32h743-pinctrl
+ - st,stm32mp157-pinctrl
+ - st,stm32mp157-z-pinctrl
+
+ '#address-cells':
+ const: 1
+ '#size-cells':
+ const: 1
+ description:
+ Defines mapping between pin controller node (parent) to
+ gpio-bank node (children).
+
+ ranges:
+ description:
+ Defines mapping between pin controller node (parent) to
+ gpio-bank node (children).
+ pins-are-numbered:
+ description:
+ Specify the subnodes are using numbered pinmux to
+ specify pins.
+ st,syscfg:
+ description: |
+ Should be phandle/offset/mask:
+ - The phandle to the syscon node which includes IRQ mux selection register.
+ - The offset of the IRQ mux selection register
+ - The field mask of IRQ mux, needed if different of 0xf.
+
+ hwlocks:
+ description: Reference to a phandle of a hardware spinlock provider node.
+ st,package:
+ description:
+ Indicates the SOC package used.
+ More details in include/dt-bindings/pinctrl/stm32-pinfunc.h
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - enum: [1, 2, 4, 8]
+
+patternProperties:
+ '^gpio@[0-9a-z]*$':
+ properties:
+ gpio-controller:
+ description:
+ Indicates this device is a GPIO controller.
+ '#gpio-cells':
+ const: 2
+ description: |
+ The first cell is the pin number.
+ The second one is the polarity
+ * 0 for active high.
+ * 1 for active low.
+
+ reg:
+ description:
+ The gpio address range, relative to the pinctrl range.
+ clocks:
+ description:
+ Clock that drives this bank.
+ st,bank-name:
+ description:
+ Should be a name string for this bank as specified in the datasheet.
+ reset:
+ description:
+ Reference to the reset controller.
+ gpio-ranges:
+ description: |
+ Define a dedicated mapping between a pin-controller and
+ a gpio controller. Format is <&phandle a b c> with:
+ -(phandle): phandle of pin-controller.
+ -(a): gpio base offset in range.
+ -(b): pin base offset in range.
+ -(c): gpio count in range.
+ This entry has to be used either if there are holes inside a bank:
+ GPIOB0/B1/B2/B14/B15 (see example 2) or if banks are not contiguous:
+ GPIOA/B/C/E...
+ NOTE: If "gpio-ranges" is used for a gpio controller, all gpio-controller
+ have to use a "gpio-ranges" entry.
+ More details in Documentation/devicetree/bindings/gpio/gpio.txt.
+
+ ngpios:
+ description:
+ Number of available gpios in a bank.
+ minimum: 1
+ maximum: 16
+
+ st,bank-ioport:
+ description:
+ Should correspond to the EXTI IOport selection (EXTI line used
+ to select GPIOs as interrupts).
+
+ required:
+ - gpio-controller
+ - '#gpio-cells'
+ - reg
+ - clocks
+ - st,bank-name
+
+ '-[0-9]*$':
+ patternProperties:
+ '^pins':
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl group available on the machine. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to muxer
+ configuration, pullups, drive, output high/low and output speed.
+ properties:
+ pinmux:
+ allOf:
+ - $ref: "/schemas/types.yaml#/definitions/uint32-array"
+ description: |
+ Integer array, represents gpio pin number and mux setting.
+ Supported pin number and mux varies for different SoCs, and are
+ defined in dt-bindings/pinctrl/<soc>-pinfunc.h directly.
+ These defines are calculated as: ((port * 16 + line) << 8) | function
+ With:
+ - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11)
+ - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15)
+ - function: The function number, can be:
+ * 0 : GPIO
+ * 1 : Alternate Function 0
+ * 2 : Alternate Function 1
+ * 3 : Alternate Function 2
+ * ...
+ * 16 : Alternate Function 15
+ * 17 : Analog
+ To simplify the usage, macro is available to generate "pinmux" field.
+ This macro is available here:
+ - include/dt-bindings/pinctrl/stm32-pinfunc.h
+ Some examples of using macro:
+ /* GPIO A9 set as alernate function 2 */
+ ... {
+ pinmux = <STM32_PINMUX('A', 9, AF2)>;
+ };
+ /* GPIO A9 set as GPIO */
+ ... {
+ pinmux = <STM32_PINMUX('A', 9, GPIO)>;
+ };
+ /* GPIO A9 set as analog */
+ ... {
+ pinmux = <STM32_PINMUX('A', 9, ANALOG)>;
+ };
+
+ bias-disable:
+ type: boolean
+ bias-pull-down:
+ type: boolean
+ bias-pull-up:
+ type: boolean
+ drive-push-pull:
+ type: boolean
+ drive-open-drain:
+ type: boolean
+ output-low:
+ type: boolean
+ output-high:
+ type: boolean
+ slew-rate:
+ description: |
+ 0: Low speed
+ 1: Medium speed
+ 2: Fast speed
+ 3: High speed
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - enum: [0, 1, 2, 3]
+
+ required:
+ - pinmux
+
+required:
+ - compatible
+ - '#address-cells'
+ - '#size-cells'
+ - ranges
+ - pins-are-numbered
+
+examples:
+ - |
+ #include <dt-bindings/pinctrl/stm32-pinfunc.h>
+ //Example 1
+ pin-controller@...20000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,stm32f429-pinctrl";
+ ranges = <0 0x40020000 0x3000>;
+ pins-are-numbered;
+
+ gpioa: gpio@0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x0 0x400>;
+ resets = <&reset_ahb1 0>;
+ st,bank-name = "GPIOA";
+ };
+ };
+
+ //Example 2 (using gpio-ranges)
+ pin-controller@...20000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,stm32f429-pinctrl";
+ ranges = <0 0x50020000 0x3000>;
+ pins-are-numbered;
+
+ gpiob: gpio@...0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x1000 0x400>;
+ resets = <&reset_ahb1 0>;
+ st,bank-name = "GPIOB";
+ gpio-ranges = <&pinctrl 0 0 16>;
+ };
+
+ gpioc: gpio@...0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x2000 0x400>;
+ resets = <&reset_ahb1 0>;
+ st,bank-name = "GPIOC";
+ ngpios = <5>;
+ gpio-ranges = <&pinctrl 0 16 3>,
+ <&pinctrl 14 30 2>;
+ };
+ };
+
+ //Example 3 pin groups
+ pin-controller@...20000 {
+ usart1_pins_a: usart1-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('A', 9, AF7)>;
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('A', 10, AF7)>;
+ bias-disable;
+ };
+ };
+ };
+
+ usart1 {
+ pinctrl-0 = <&usart1_pins_a>;
+ pinctrl-names = "default";
+ };
+
+...
--
2.7.4
Powered by blists - more mailing lists