[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20190705112724.GA4294@kroah.com>
Date: Fri, 5 Jul 2019 13:27:24 +0200
From: Greg KH <gregkh@...uxfoundation.org>
To: Pawel Laszczak <pawell@...ence.com>
Cc: devicetree@...r.kernel.org, felipe.balbi@...ux.intel.com,
linux-usb@...r.kernel.org, hdegoede@...hat.com,
heikki.krogerus@...ux.intel.com, robh+dt@...nel.org, rogerq@...com,
linux-kernel@...r.kernel.org, jbergsagel@...com, nsekhar@...com,
nm@...com, sureshp@...ence.com, peter.chen@....com,
jpawar@...ence.com, kurahul@...ence.com
Subject: Re: [PATCH v9 2/6] usb:gadget Separated decoding functions from dwc3
driver.
On Fri, Jul 05, 2019 at 11:57:14AM +0100, Pawel Laszczak wrote:
> Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
> to driver/usb/gadget/debug.c file. These moved functions include:
> dwc3_decode_get_status
> dwc3_decode_set_clear_feature
> dwc3_decode_set_address
> dwc3_decode_get_set_descriptor
> dwc3_decode_get_configuration
> dwc3_decode_set_configuration
> dwc3_decode_get_intf
> dwc3_decode_set_intf
> dwc3_decode_synch_frame
> dwc3_decode_set_sel
> dwc3_decode_set_isoch_delay
> dwc3_decode_ctrl
>
> These functions are used also in inroduced cdns3 driver.
>
> All functions prefixes were changed from dwc3 to usb.
> Also, function's parameters has been extended according to the name
> of fields in standard SETUP packet.
> Additionally, patch adds usb_decode_ctrl function to
> include/linux/usb/gadget.h file.
No it does not :(
> Signed-off-by: Pawel Laszczak <pawell@...ence.com>
> ---
> drivers/usb/common/Makefile | 5 +
> drivers/usb/common/debug.c | 268 ++++++++++++++++++++++++++++++++++++
> drivers/usb/dwc3/debug.h | 252 ---------------------------------
> drivers/usb/dwc3/trace.h | 2 +-
> include/linux/usb/ch9.h | 25 ++++
> 5 files changed, 299 insertions(+), 253 deletions(-)
> create mode 100644 drivers/usb/common/debug.c
>
> diff --git a/drivers/usb/common/Makefile b/drivers/usb/common/Makefile
> index 0a7c45e85481..cdc66b59a6f0 100644
> --- a/drivers/usb/common/Makefile
> +++ b/drivers/usb/common/Makefile
> @@ -5,6 +5,11 @@
>
> obj-$(CONFIG_USB_COMMON) += usb-common.o
> usb-common-y += common.o
> +
> +ifneq ($(CONFIG_TRACING),)
> + usb-common-y += debug.o
> +endif
So only enable this if tracing is not emabled? Or if enabled? I'm
confused, isn't there an easier way to write this?
thanks,
greg k-h
Powered by blists - more mailing lists