[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20191002072201.GL896@valkosipuli.retiisi.org.uk>
Date: Wed, 2 Oct 2019 10:22:01 +0300
From: Sakari Ailus <sakari.ailus@....fi>
To: Vishal Sagar <vishal.sagar@...inx.com>
Cc: Hyun Kwon <hyun.kwon@...inx.com>,
Laurent Pinchart <laurent.pinchart@...asonboard.com>,
Mauro Carvalho Chehab <mchehab@...nel.org>,
Michal Simek <michal.simek@...inx.com>,
Rob Herring <robh+dt@...nel.org>,
Mark Rutland <mark.rutland@....com>,
linux-kernel@...r.kernel.org, linux-media@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
Dinesh Kumar <dineshk@...inx.com>,
Sandip Kothari <sandipk@...inx.com>
Subject: Re: [PATCH 1/2] media: dt-bindings: media: xilinx: Add Xilinx
UHD-SDI Receiver Subsystem
Hi Vishal,
On Tue, Jun 04, 2019 at 07:25:55PM +0530, Vishal Sagar wrote:
> Add bindings documentation for Xilinx UHD-SDI Receiver Subsystem.
>
> The Xilinx UHD-SDI Receiver Subsystem consists of SMPTE UHD-SDI (RX) IP
> core, an SDI RX to Video Bridge IP core to convert SDI video to native
> video and a Video In to AXI4-Stream IP core to convert native video to
> AXI4-Stream.
>
> Signed-off-by: Vishal Sagar <vishal.sagar@...inx.com>
> ---
> .../bindings/media/xilinx/xlnx,sdirxss.txt | 80 ++++++++++++++++++++++
> 1 file changed, 80 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.txt
>
> diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.txt
> new file mode 100644
> index 0000000..8445bee
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.txt
> @@ -0,0 +1,80 @@
> +
> +Xilinx SMPTE UHD-SDI Receiver Subsystem Device Tree Bindings
> +------------------------------------------------------------
> +
> +The SMPTE UHD-SDI Receiver (RX) Subsystem allows you to quickly create systems
> +based on SMPTE SDI protocols. It receives unaligned native SDI streams from
> +the SDI GT PHY and outputs an AXI4-Stream video stream, native video, or
> +native SDI using Xilinx transceivers as the physical layer.
> +
> +The subsystem consists of
> +1 - SMPTE UHD-SDI Rx
> +2 - SDI Rx to Native Video Bridge
> +3 - Video In to AXI4-Stream Bridge
> +
> +The subsystem can capture SDI streams in utpo 12G mode and output a dual pixel
> +per clock YUV 422 or 420 10 bits per component AXI4-Stream.
> +
> +Required properties:
> +--------------------
> +- compatible: Must contain "xlnx,v-smpte-uhdsdi-rx-ss"
> +- reg: Physical base address and length of the registers set for the device.
> +- interrupts: Contains the interrupt line number.
> +- clocks: List of phandles to AXI4-Lite clock, core clock to SMPTE UHD-SDI Rx
> + and Video clocks.
> +- clock-names: Must contain "s_axi_aclk", "sdi_rx_clk" and "video_out_clk" in
> + the same order as clocks listed in clocks property.
> +- xlnx,line-rate: The maximum mode supported by the design. Possible values are
> + are as below -
> + 12G_SDI_8DS - 12G mode
> + 6G_SDI - 6G mode
> + 3G_SDI - 3G mode
Is this specific to a port?
I was wondering whether we should include this to video-interfaces.txt bus
type list, and V4L2 MBUS types. This way it could be also parsed by the
v4l2-fwnode framework.
Looking at the Wikipedia article, there are preceding standards, too, that
are referred to by a pair of letters:
<URL:https://en.wikipedia.org/wiki/Serial_digital_interface#Standards>
What does "DS" stand for?
> +
> +Optional properties:
> +--------------------
> +- xlnx,include-edh: This is present when the Error Detection and Handling
> + processor is enabled in design.
> +
> +Ports
> +-----
> +The device node shall contain one 'port' child node as defined in
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Generally the SDI port is connected to a device like SDI Broadcast camera which
> +is independently controlled. Hence port@0 is a source port which can be
> +connected to downstream IP which can work with AXI4 Stream data.
> +
> +Required port properties:
> +-------------------------
> +- reg: 0 - for source port.
> +
> +- xlnx,video-format: This can be XVIP_VF_YUV_422 or XVIP_VF_YUV_420.
Is this a property of the hardware?
> +- xlnx,video-width: This is should be 10.
This, too. If there's just one choice, is there a need for the property?
> +
> +Example:
> + v_smpte_uhdsdi_rx_ss: v_smpte_uhdsdi_rx_ss@...00000 {
> + compatible = "xlnx,v-smpte-uhdsdi-rx-ss";
> + interrupt-parent = <&gic>;
> + interrupts = <0 89 4>;
> + reg = <0x0 0x80000000 0x0 0x10000>;
> + xlnx,include-edh;
> + xlnx,line-rate = "12G_SDI_8DS";
> + clocks = <&clk_1>, <&si570_1>, <&clk_2>;
> + clock-names = "s_axi_aclk", "sdi_rx_clk", "video_out_clk";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + xlnx,video-format = <XVIP_VF_YUV_422>;
> + xlnx,video-width = <10>;
> +
> + sdirx_out: endpoint {
> + remote-endpoint = <&vcap_sdirx_in>;
> + };
> + };
> + };
> + };
--
Regards,
Sakari Ailus
Powered by blists - more mailing lists