[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20191004133207.6663-2-linux@rasmusvillemoes.dk>
Date: Fri, 4 Oct 2019 15:32:02 +0200
From: Rasmus Villemoes <linux@...musvillemoes.dk>
To: Thierry Reding <thierry.reding@...il.com>,
Uwe Kleine-König
<u.kleine-koenig@...gutronix.de>, Shawn Guo <shawnguo@...nel.org>,
Sascha Hauer <s.hauer@...gutronix.de>,
Pengutronix Kernel Team <kernel@...gutronix.de>,
Fabio Estevam <festevam@...il.com>,
NXP Linux Team <linux-imx@....com>
Cc: devicetree@...r.kernel.org, Rob Herring <robh+dt@...nel.org>,
Rasmus Villemoes <linux@...musvillemoes.dk>,
linux-pwm@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-kernel@...r.kernel.org
Subject: [PATCH v2 1/6] pwm: mxs: implement ->apply
In preparation for supporting setting the polarity, switch the driver
to support the ->apply method.
Signed-off-by: Rasmus Villemoes <linux@...musvillemoes.dk>
---
drivers/pwm/pwm-mxs.c | 70 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 70 insertions(+)
diff --git a/drivers/pwm/pwm-mxs.c b/drivers/pwm/pwm-mxs.c
index b14376b47ac8..10efd3de0bb3 100644
--- a/drivers/pwm/pwm-mxs.c
+++ b/drivers/pwm/pwm-mxs.c
@@ -26,6 +26,7 @@
#define PERIOD_PERIOD_MAX 0x10000
#define PERIOD_ACTIVE_HIGH (3 << 16)
#define PERIOD_INACTIVE_LOW (2 << 18)
+#define PERIOD_POLARITY_NORMAL (PERIOD_ACTIVE_HIGH | PERIOD_INACTIVE_LOW)
#define PERIOD_CDIV(div) (((div) & 0x7) << 20)
#define PERIOD_CDIV_MAX 8
@@ -41,6 +42,74 @@ struct mxs_pwm_chip {
#define to_mxs_pwm_chip(_chip) container_of(_chip, struct mxs_pwm_chip, chip)
+static int mxs_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
+{
+ struct mxs_pwm_chip *mxs = to_mxs_pwm_chip(chip);
+ int ret, div = 0;
+ unsigned int period_cycles, duty_cycles;
+ unsigned long rate;
+ unsigned long long c;
+
+ if (state->polarity != PWM_POLARITY_NORMAL)
+ return -ENOTSUPP;
+
+ /*
+ * If the PWM channel is disabled, make sure to turn on the
+ * clock before calling clk_get_rate() and writing to the
+ * registers. Otherwise, just keep it enabled.
+ */
+ if (!pwm_is_enabled(pwm)) {
+ ret = clk_prepare_enable(mxs->clk);
+ if (ret)
+ return ret;
+ }
+
+ if (!state->enabled && pwm_is_enabled(pwm))
+ writel(1 << pwm->hwpwm, mxs->base + PWM_CTRL + CLR);
+
+ rate = clk_get_rate(mxs->clk);
+ while (1) {
+ c = rate / cdiv[div];
+ c = c * state->period;
+ do_div(c, 1000000000);
+ if (c < PERIOD_PERIOD_MAX)
+ break;
+ div++;
+ if (div >= PERIOD_CDIV_MAX)
+ return -EINVAL;
+ }
+
+ period_cycles = c;
+ c *= state->duty_cycle;
+ do_div(c, state->period);
+ duty_cycles = c;
+
+ /*
+ * The data sheet the says registers must be written to in
+ * this order (ACTIVEn, then PERIODn). Also, the new settings
+ * only take effect at the beginning of a new period, avoiding
+ * glitches.
+ */
+ writel(duty_cycles << 16,
+ mxs->base + PWM_ACTIVE0 + pwm->hwpwm * 0x20);
+ writel(PERIOD_PERIOD(period_cycles) | PERIOD_POLARITY_NORMAL | PERIOD_CDIV(div),
+ mxs->base + PWM_PERIOD0 + pwm->hwpwm * 0x20);
+
+ if (state->enabled) {
+ if (!pwm_is_enabled(pwm)) {
+ /*
+ * The clock was enabled above. Just enable
+ * the channel in the control register.
+ */
+ writel(1 << pwm->hwpwm, mxs->base + PWM_CTRL + SET);
+ }
+ } else {
+ clk_disable_unprepare(mxs->clk);
+ }
+ return 0;
+}
+
static int mxs_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
int duty_ns, int period_ns)
{
@@ -116,6 +185,7 @@ static void mxs_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
}
static const struct pwm_ops mxs_pwm_ops = {
+ .apply = mxs_pwm_apply,
.config = mxs_pwm_config,
.enable = mxs_pwm_enable,
.disable = mxs_pwm_disable,
--
2.20.1
Powered by blists - more mailing lists