| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <4e36a8fb-92e2-943e-f778-cf61e79ebbc4@flowbird.group>
Date: Wed, 20 Nov 2019 12:32:04 +0100
From: Martin Fuzzey <martin.fuzzey@...wbird.group>
To: Sebastian Reichel <sebastian.reichel@...labora.com>,
Dmitry Torokhov <dmitry.torokhov@...il.com>,
Ahmet Inan <inan@...tec.de>
Cc: linux-input@...r.kernel.org, linux-kernel@...r.kernel.org,
kernel@...labora.com
Subject: Re: [PATCHv1 1/2] Input: EXC3000: add EXC80Hxx support
Hi Sebastien,
On 07/11/2019 19:10, Sebastian Reichel wrote:
> This adds support for EXC80Hxx controllers, which uses
> a different event type id and has two extra bits for the
> resolution (so the maximum is 16384 instead of 4096).
>
> The patch has been tested with EXC80H60 and EXC80H84.
Ah I'm doing the same thing :)
> Signed-off-by: Sebastian Reichel <sebastian.reichel@...labora.com>
> ---
> .../bindings/input/touchscreen/exc3000.txt | 6 ++--
> drivers/input/touchscreen/exc3000.c | 34 ++++++++++++++-----
> 2 files changed, 30 insertions(+), 10 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt b/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt
> index 68291b94fec2..057b680f0420 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/exc3000.txt
> @@ -1,7 +1,9 @@
> -* EETI EXC3000 Multiple Touch Controller
> +* EETI EXC3000 and EXC80Hxx Multiple Touch Controller
>
> Required properties:
> -- compatible: must be "eeti,exc3000"
> +- compatible: must be one of
> + * "eeti,exc3000"
> + * "eeti,exc80hxx"
> - reg: i2c slave address
> - interrupts: touch controller interrupt
> - touchscreen-size-x: See touchscreen.txt
> diff --git a/drivers/input/touchscreen/exc3000.c b/drivers/input/touchscreen/exc3000.c
> index e007e2e8f626..7d695022082c 100644
> --- a/drivers/input/touchscreen/exc3000.c
> +++ b/drivers/input/touchscreen/exc3000.c
> @@ -23,11 +23,20 @@
> #define EXC3000_SLOTS_PER_FRAME 5
> #define EXC3000_LEN_FRAME 66
> #define EXC3000_LEN_POINT 10
> -#define EXC3000_MT_EVENT 6
> +
> +#define EXC3000_MT1_EVENT 0x06
> +#define EXC3000_MT2_EVENT 0x18
> +
> #define EXC3000_TIMEOUT_MS 100
>
> +enum exc3000_device_type {
> + EETI_EXC3000,
> + EETI_EXC80Hxx
> +};
> +
> struct exc3000_data {
> struct i2c_client *client;
> + enum exc3000_device_type type;
> struct input_dev *input;
> struct touchscreen_properties prop;
> struct timer_list timer;
> @@ -76,8 +85,10 @@ static int exc3000_read_frame(struct i2c_client *client, u8 *buf)
> if (ret != EXC3000_LEN_FRAME)
> return -EIO;
>
> - if (get_unaligned_le16(buf) != EXC3000_LEN_FRAME ||
> - buf[2] != EXC3000_MT_EVENT)
> + if (get_unaligned_le16(buf) != EXC3000_LEN_FRAME)
> + return -EINVAL;
> +
> + if (buf[2] != EXC3000_MT1_EVENT && buf[2] != EXC3000_MT2_EVENT)
> return -EINVAL;
>
Are we sure the EXC80 will *always* use MT2_EVENT (and that there is not
some configuration where it can send MT1_EVENTS).
Because, if this happens we will have declared a 14 bit resolution to
the input core but process a 12 bit value.
I think it is better to declare the resolution based on the device type
(as you have done) but interpret the data based on the MT1 vs MT2 event
code, shifting 2 bits if needed.
> @@ -168,8 +180,13 @@ static int exc3000_probe(struct i2c_client *client,
> input->name = "EETI EXC3000 Touch Screen";
Shouldn't the name change too?
> input->id.bustype = BUS_I2C;
>
> - input_set_abs_params(input, ABS_MT_POSITION_X, 0, 4095, 0, 0);
> - input_set_abs_params(input, ABS_MT_POSITION_Y, 0, 4095, 0, 0);
> + if (data->type == EETI_EXC80Hxx) {
> + input_set_abs_params(input, ABS_MT_POSITION_X, 0, 16383, 0, 0);
> + input_set_abs_params(input, ABS_MT_POSITION_Y, 0, 16383, 0, 0);
> + } else {
> + input_set_abs_params(input, ABS_MT_POSITION_X, 0, 4095, 0, 0);
> + input_set_abs_params(input, ABS_MT_POSITION_Y, 0, 4095, 0, 0);
> + }
> touchscreen_parse_properties(input, true, &data->prop);
>
> error = input_mt_init_slots(input, EXC3000_NUM_SLOTS,
> @@ -191,14 +208,15 @@ static int exc3000_probe(struct i2c_client *client,
> }
>
> static const struct i2c_device_id exc3000_id[] = {
> - { "exc3000", 0 },
> - { }
> + { "exc3000", EETI_EXC3000 },
> + { "exc80hxx", EETI_EXC80Hxx }
> };
> MODULE_DEVICE_TABLE(i2c, exc3000_id);
>
> #ifdef CONFIG_OF
> static const struct of_device_id exc3000_of_match[] = {
> - { .compatible = "eeti,exc3000" },
> + { .compatible = "eeti,exc3000", .data = (const void*) EETI_EXC3000 },
> + { .compatible = "eeti,exc80hxx", .data = (const void*) EETI_EXC80Hxx },
> { }
> };
> MODULE_DEVICE_TABLE(of, exc3000_of_match);
If driver_data is defined in the I2C device table and the compatible
string, minus the vendor prefix, matches the i2c device id it is not
necessary to define the driver_data in the of_match table as well.
How about defining a "exc_device_info" structure, containing name,
resolution etc and storing a pointer to a constant instance of that in
the match tables rather than just a type code.
That way the "if (data->type)" tests could be removed and the info
structure accessed directly.
Something like:
struct exc_dev_info {
const char *name;
u16 x_res;
u16 y_res;
};
static int exc3000_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
const struct exc_dev_info *dev_info;
...
dev_info = (const struct exc_dev_info *)id->driver_data;
...
input->name = dev_info->name;
input->id.bustype = BUS_I2C;
input_set_abs_params(input, ABS_MT_POSITION_X, 0,
dev_info->x_res - 1, 0, 0);
input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
dev_info->y_res - 1, 0, 0);
touchscreen_parse_properties(input, true, &data->prop);
static const struct exc_dev_info exc3000_dev_info = {
.name = "EETI EXC3000 Touch Screen",
.x_res = 4096,
.y_res = 4096,
};
static const struct exc_dev_info exc80_dev_info = {
.name = "EETI EXC80 Touch Screen",
.x_res = 16384,
.y_res = 16384,
};
static const struct i2c_device_id exc3000_id[] = {
{ "exc3000", (kernel_ulong_t)&exc3000_dev_info },
{ "exc80", (kernel_ulong_t)&exc80_dev_info },
{ }
};
MODULE_DEVICE_TABLE(i2c, exc3000_id);
One other thing I have noticed is that the exc80h does not appear to
need the i2c_send before read that is done in exc3000_read_frame()
The vendor "egalax_i2c" driver doesn't do it either and I can't see
anything in the "I2C programming guide" mentionning this.
Ahmet's original commit introducing the driver says
" To be able to work with the higher 400KHz I2C bus rate, one must
successfully send a special package prior _each_ read or the controller
will refuse to cooperate."
This doesn't seem to be an issue at 400KHz for the 80h at least, though
keeping it doesn't seem to hurt either.
Maybe make this device dependant too?
Regards,
Martin
Powered by blists - more mailing lists