[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20200121162734.464123fd@xps13>
Date: Tue, 21 Jan 2020 16:27:34 +0100
From: Miquel Raynal <miquel.raynal@...tlin.com>
To: "Shivamurthy Shastri (sshivamurthy)" <sshivamurthy@...ron.com>
Cc: Richard Weinberger <richard@....at>,
Vignesh Raghavendra <vigneshr@...com>,
Boris Brezillon <bbrezillon@...nel.org>,
Frieder Schrempf <frieder.schrempf@...tron.de>,
"linux-mtd@...ts.infradead.org" <linux-mtd@...ts.infradead.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
Shivamurthy Shastri <shiva.linuxworks@...il.com>
Subject: Re: [EXT] Re: [PATCH 3/4] mtd: spinand: Add M70A series Micron SPI
NAND devices
Hi Shivamurthy,
"Shivamurthy Shastri (sshivamurthy)" <sshivamurthy@...ron.com> wrote on
Tue, 21 Jan 2020 14:59:11 +0000:
> Hi Miquel,
>
> >
> > Hi Shivamurthy,
> >
> > "Shivamurthy Shastri (sshivamurthy)" <sshivamurthy@...ron.com> wrote
> > on
> > Tue, 21 Jan 2020 12:23:20 +0000:
> >
> > > Hi Miquel,
> > >
> > > >
> > > > Hi Shiva,
> > > >
> > > > This is remark common to the four patches: you miss the 'v2' prefix in
> > > > the object.
> > > >
> > >
> > > Sorry for this mistake.
> > > I recognized this after sending out the patches.
> > >
> > > > shiva.linuxworks@...il.com wrote on Sun, 19 Jan 2020 15:54:31 +0100:
> > > >
> > > > > From: Shivamurthy Shastri <sshivamurthy@...ron.com>
> > > > >
> > > > > Add device table for M70A series Micron SPI NAND devices.
> > > > >
> > > > > While at it, disable the Continuous Read feature which is enabled by
> > > > > default.
> > > >
> > > > Can you please give us more detail on why this is an issue?
> > >
> > > "Continuous Read" is the new feature added by the Micron for
> > > M70A series devices. If this feature is enabled, the READ command
> > > doesn't output the OOB area. The following short description
> > > describes this feature.
> > >
> > > Description:
> > > If the Continuous Read feature is enabled, the device provides
> > > the capability to read the whole block with a single command.
> > > However, the read command doesn't output the OOB area.
> > >
> > > Read command behavior (if Continuous Read enabled):
> > > The READ CACHE command doesn't require the starting column address.
> > > The device always output the data starting from the first column of the
> > > cache register, and once the end of the cache register reached, the data
> > > output continues through the next page. With the continuous read mode,
> > > it is possible to read out the entire block using a single READ command, and
> > > once the end of the block reached, the output pins become High-Z state.
> >
> > Ok I understand better. In this case there is no need to split this
> > commit, instead just reword the commit log to something like:
> >
> > --->8---
> > Add device table for M70A series Micron SPI-NAND devices.
> >
> > As opposed to the M60A series already supported, M70A parts have the
> > "Continuous Read" feature enabled by default which does not fit the
> > subsystem needs.
> >
> > <here explain the feature>.
> >
> > Hence, we disable the feature at probe time.
> > ---8<---
> >
>
> Sure, I will change as per your suggestion.
>
> > However, below, you disable this bit for all the parts. Is this really
> > ok? Souldn't we make it more specific to this series?
>
> It is ok because this bit is unused in other series.
I would rather prefer to avoid this kind of arrangement. Please change
this bit only for the series which has it.
Thanks,
Miquèl
Powered by blists - more mailing lists