linux-kernel - Re: [PATCH v6 1/4] dt-bindings: display: mediatek: update dpi supported chips

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <1582533982.12922.5.camel@mtksdaap41>
Date:   Mon, 24 Feb 2020 16:46:22 +0800
From:   CK Hu <ck.hu@...iatek.com>
To:     Jitao Shi <jitao.shi@...iatek.com>
CC:     Rob Herring <robh+dt@...nel.org>,
        Mark Rutland <mark.rutland@....com>,
        Matthias Brugger <matthias.bgg@...il.com>,
        Daniel Vetter <daniel@...ll.ch>,
        David Airlie <airlied@...ux.ie>,
        <dri-devel@...ts.freedesktop.org>, <linux-kernel@...r.kernel.org>,
        <linux-mediatek@...ts.infradead.org>, <devicetree@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <srv_heupstream@...iatek.com>, <yingjoe.chen@...iatek.com>,
        <eddie.huang@...iatek.com>, <cawa.cheng@...iatek.com>,
        <bibby.hsieh@...iatek.com>, <stonea168@....com>,
        <huijuan.xie@...iatek.com>
Subject: Re: [PATCH v6 1/4] dt-bindings: display: mediatek: update dpi
 supported chips

Hi, Jitao:

On Fri, 2020-02-21 at 19:28 +0800, Jitao Shi wrote:
> Add decriptions about supported chips, including MT2701 & MT8173 &
> mt8183
> 
> 1. Add more chips support. ex. MT2701 & MT8173 & MT8183
> 2. Add property "dpi_pin_mode_swap" and "pinctrl-names" gpio mode dpi mode and
>    gpio oupput-low to avoid leakage current.
> 3. Add property "dpi_dual_edge" to config the dpi pin output mode dual edge or
>    single edge sample data.
> 
> Signed-off-by: Jitao Shi <jitao.shi@...iatek.com>
> ---
>  .../bindings/display/mediatek/mediatek,dpi.txt        | 11 +++++++++++
>  1 file changed, 11 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> index b6a7e7397b8b..cd6a1469c8b7 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> @@ -7,6 +7,7 @@ output bus.
>  
>  Required properties:
>  - compatible: "mediatek,<chip>-dpi"
> +  the supported chips are mt2701 , mt8173 and mt8183.
>  - reg: Physical base address and length of the controller's registers
>  - interrupts: The interrupt signal from the function block.
>  - clocks: device clocks
> @@ -16,6 +17,11 @@ Required properties:
>    Documentation/devicetree/bindings/graph.txt. This port should be connected
>    to the input port of an attached HDMI or LVDS encoder chip.
>  
> +Optional properties:
> +- dpi_pin_mode_swap: Swap the pin mode between dpi mode and gpio mode.
> +- pinctrl-names: Contain "gpiomode" and "dpimode".
> +- dpi_dual_edge: Control the RGB 24bit data on 12 pins or 24 pins.

I've find that in [1], there are already a property of "pclk-sample"
which like this, but it only have rising (1) or falling (0) status. Does
that property describe the same thing with this property? If they are
the same, I think you should add new state, dual (2), for "pclk-sample".

[1]
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/media/video-interfaces.txt?h=v5.6-rc3

Regards,
CK

> +
>  Example:
>  
>  dpi0: dpi@...1d000 {
> @@ -26,6 +32,11 @@ dpi0: dpi@...1d000 {
>  		 <&mmsys CLK_MM_DPI_ENGINE>,
>  		 <&apmixedsys CLK_APMIXED_TVDPLL>;
>  	clock-names = "pixel", "engine", "pll";
> +	dpi_dual_edge;
> +	dpi_pin_mode_swap;
> +	pinctrl-names = "gpiomode", "dpimode";
> +	pinctrl-0 = <&dpi_pin_gpio>;
> +	pinctrl-1 = <&dpi_pin_func>;
>  
>  	port {
>  		dpi0_out: endpoint {