linux-kernel - Re: [PATCH v6 1/4] dt-bindings: display: mediatek: update dpi supported chips

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <1582596033.12484.1.camel@mszsdaap41>
Date:   Tue, 25 Feb 2020 10:00:33 +0800
From:   Jitao Shi <jitao.shi@...iatek.com>
To:     CK Hu <ck.hu@...iatek.com>
CC:     Rob Herring <robh+dt@...nel.org>,
        Mark Rutland <mark.rutland@....com>,
        Matthias Brugger <matthias.bgg@...il.com>,
        Daniel Vetter <daniel@...ll.ch>,
        David Airlie <airlied@...ux.ie>,
        <dri-devel@...ts.freedesktop.org>, <linux-kernel@...r.kernel.org>,
        <linux-mediatek@...ts.infradead.org>, <devicetree@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <srv_heupstream@...iatek.com>, <yingjoe.chen@...iatek.com>,
        <eddie.huang@...iatek.com>, <cawa.cheng@...iatek.com>,
        <bibby.hsieh@...iatek.com>, <stonea168@....com>,
        <huijuan.xie@...iatek.com>
Subject: Re: [PATCH v6 1/4] dt-bindings: display: mediatek: update dpi
 supported chips

On Mon, 2020-02-24 at 15:50 +0800, CK Hu wrote:
> Hi, Jitao:
> 
> On Fri, 2020-02-21 at 19:28 +0800, Jitao Shi wrote:
> > Add decriptions about supported chips, including MT2701 & MT8173 &
> > mt8183
> > 
> > 1. Add more chips support. ex. MT2701 & MT8173 & MT8183
> > 2. Add property "dpi_pin_mode_swap" and "pinctrl-names" gpio mode dpi mode and
> >    gpio oupput-low to avoid leakage current.
> > 3. Add property "dpi_dual_edge" to config the dpi pin output mode dual edge or
> >    single edge sample data.
> > 
> > Signed-off-by: Jitao Shi <jitao.shi@...iatek.com>
> > ---
> >  .../bindings/display/mediatek/mediatek,dpi.txt        | 11 +++++++++++
> >  1 file changed, 11 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> > index b6a7e7397b8b..cd6a1469c8b7 100644
> > --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> > +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> > @@ -7,6 +7,7 @@ output bus.
> >  
> >  Required properties:
> >  - compatible: "mediatek,<chip>-dpi"
> > +  the supported chips are mt2701 , mt8173 and mt8183.
> >  - reg: Physical base address and length of the controller's registers
> >  - interrupts: The interrupt signal from the function block.
> >  - clocks: device clocks
> > @@ -16,6 +17,11 @@ Required properties:
> >    Documentation/devicetree/bindings/graph.txt. This port should be connected
> >    to the input port of an attached HDMI or LVDS encoder chip.
> >  
> > +Optional properties:
> > +- dpi_pin_mode_swap: Swap the pin mode between dpi mode and gpio mode.
> 
> When you have both pinctrl-name of "gpiomode" and "dpimode", it imply
> that dpi_pin_mode_swap = true, isn't it? If so, I think this property is
> redundant.
> 
> Regards,
> CK

Yes,I'll fix it next verision.

Best Regards
Jitao

> 
> > +- pinctrl-names: Contain "gpiomode" and "dpimode".
> > +- dpi_dual_edge: Control the RGB 24bit data on 12 pins or 24 pins.
> > +
> >  Example:
> >  
> >  dpi0: dpi@...1d000 {
> > @@ -26,6 +32,11 @@ dpi0: dpi@...1d000 {
> >  		 <&mmsys CLK_MM_DPI_ENGINE>,
> >  		 <&apmixedsys CLK_APMIXED_TVDPLL>;
> >  	clock-names = "pixel", "engine", "pll";
> > +	dpi_dual_edge;
> > +	dpi_pin_mode_swap;
> > +	pinctrl-names = "gpiomode", "dpimode";
> > +	pinctrl-0 = <&dpi_pin_gpio>;
> > +	pinctrl-1 = <&dpi_pin_func>;
> >  
> >  	port {
> >  		dpi0_out: endpoint {
> 
>