| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20200304130811.GP2248@voidbox>
Date: Wed, 4 Mar 2020 14:08:11 +0100
From: Remi Pommarel <repk@...plefau.lt>
To: Kishon Vijay Abraham I <kishon@...com>
Cc: Yue Wang <yue.wang@...ogic.com>,
Kevin Hilman <khilman@...libre.com>,
Lorenzo Pieralisi <lorenzo.pieralisi@....com>,
Bjorn Helgaas <bhelgaas@...gle.com>,
Neil Armstrong <narmstrong@...libre.com>,
Martin Blumenstingl <martin.blumenstingl@...glemail.com>,
Rob Herring <robh+dt@...nel.org>,
Jerome Brunet <jbrunet@...libre.com>,
linux-amlogic@...ts.infradead.org, linux-kernel@...r.kernel.org,
devicetree@...r.kernel.org, linux-pci@...r.kernel.org
Subject: Re: [PATCH v6 6/7] phy: amlogic: Add Amlogic AXG PCIE PHY Driver
On Wed, Mar 04, 2020 at 04:31:24PM +0530, Kishon Vijay Abraham I wrote:
>
>
> On 24/01/20 4:59 am, Remi Pommarel wrote:
> > This adds support for the PCI PHY found in the Amlogic AXG SoC Family.
> > This will allow to mutualize code in pci-meson.c between AXG and G12A
> > SoC.
> >
> > This PHY also uses and chains an analog PHY, which on AXG platform
> > is needed to have reliable PCIe communication.
>
> Is the analog PHY an independent block and can be used with other PHYs?
It is documented as a separate block yes, but I think it is unlikely
that it will be used with other PHYs than the PCIe or the MIPI one of
the AXG SoC.
Thanks,
Remi
>
> For the patch itself
> Acked-by: Kishon Vijay Abraham I <kishon@...com>
>
> Thanks
> Kishon
> >
> > Signed-off-by: Remi Pommarel <repk@...plefau.lt>
> > ---
> > drivers/phy/amlogic/Kconfig | 11 ++
> > drivers/phy/amlogic/Makefile | 1 +
> > drivers/phy/amlogic/phy-meson-axg-pcie.c | 192 +++++++++++++++++++++++
> > 3 files changed, 204 insertions(+)
> > create mode 100644 drivers/phy/amlogic/phy-meson-axg-pcie.c
> >
> > diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
> > index 8c9cf2403591..71801e30d601 100644
> > --- a/drivers/phy/amlogic/Kconfig
> > +++ b/drivers/phy/amlogic/Kconfig
> > @@ -60,6 +60,17 @@ config PHY_MESON_G12A_USB3_PCIE
> > in Meson G12A SoCs.
> > If unsure, say N.
> >
> > +config PHY_MESON_AXG_PCIE
> > + tristate "Meson AXG PCIE PHY driver"
> > + default ARCH_MESON
> > + depends on OF && (ARCH_MESON || COMPILE_TEST)
> > + select GENERIC_PHY
> > + select REGMAP_MMIO
> > + help
> > + Enable this to support the Meson MIPI + PCIE PHY found
> > + in Meson AXG SoCs.
> > + If unsure, say N.
> > +
> > config PHY_MESON_AXG_MIPI_PCIE_ANALOG
> > tristate "Meson AXG MIPI + PCIE analog PHY driver"
> > default ARCH_MESON
> > diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
> > index 0aecf92d796a..e2baa133f7af 100644
> > --- a/drivers/phy/amlogic/Makefile
> > +++ b/drivers/phy/amlogic/Makefile
> > @@ -4,4 +4,5 @@ obj-$(CONFIG_PHY_MESON_GXL_USB2) += phy-meson-gxl-usb2.o
> > obj-$(CONFIG_PHY_MESON_G12A_USB2) += phy-meson-g12a-usb2.o
> > obj-$(CONFIG_PHY_MESON_GXL_USB3) += phy-meson-gxl-usb3.o
> > obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE) += phy-meson-g12a-usb3-pcie.o
> > +obj-$(CONFIG_PHY_MESON_AXG_PCIE) += phy-meson-axg-pcie.o
> > obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG) += phy-meson-axg-mipi-pcie-analog.o
> > diff --git a/drivers/phy/amlogic/phy-meson-axg-pcie.c b/drivers/phy/amlogic/phy-meson-axg-pcie.c
> > new file mode 100644
> > index 000000000000..377ed0dcd0d9
> > --- /dev/null
> > +++ b/drivers/phy/amlogic/phy-meson-axg-pcie.c
> > @@ -0,0 +1,192 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Amlogic AXG PCIE PHY driver
> > + *
> > + * Copyright (C) 2020 Remi Pommarel <repk@...plefau.lt>
> > + */
> > +#include <linux/module.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/regmap.h>
> > +#include <linux/reset.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/bitfield.h>
> > +#include <dt-bindings/phy/phy.h>
> > +
> > +#define MESON_PCIE_REG0 0x00
> > +#define MESON_PCIE_COMMON_CLK BIT(4)
> > +#define MESON_PCIE_PORT_SEL GENMASK(3, 2)
> > +#define MESON_PCIE_CLK BIT(1)
> > +#define MESON_PCIE_POWERDOWN BIT(0)
> > +
> > +#define MESON_PCIE_TWO_X1 FIELD_PREP(MESON_PCIE_PORT_SEL, 0x3)
> > +#define MESON_PCIE_COMMON_REF_CLK FIELD_PREP(MESON_PCIE_COMMON_CLK, 0x1)
> > +#define MESON_PCIE_PHY_INIT (MESON_PCIE_TWO_X1 | \
> > + MESON_PCIE_COMMON_REF_CLK)
> > +#define MESON_PCIE_RESET_DELAY 500
> > +
> > +struct phy_axg_pcie_priv {
> > + struct phy *phy;
> > + struct phy *analog;
> > + struct regmap *regmap;
> > + struct reset_control *reset;
> > +};
> > +
> > +static const struct regmap_config phy_axg_pcie_regmap_conf = {
> > + .reg_bits = 8,
> > + .val_bits = 32,
> > + .reg_stride = 4,
> > + .max_register = MESON_PCIE_REG0,
> > +};
> > +
> > +static int phy_axg_pcie_power_on(struct phy *phy)
> > +{
> > + struct phy_axg_pcie_priv *priv = phy_get_drvdata(phy);
> > + int ret;
> > +
> > + ret = phy_power_on(priv->analog);
> > + if (ret != 0)
> > + return ret;
> > +
> > + regmap_update_bits(priv->regmap, MESON_PCIE_REG0,
> > + MESON_PCIE_POWERDOWN, 0);
> > + return 0;
> > +}
> > +
> > +static int phy_axg_pcie_power_off(struct phy *phy)
> > +{
> > + struct phy_axg_pcie_priv *priv = phy_get_drvdata(phy);
> > + int ret;
> > +
> > + ret = phy_power_off(priv->analog);
> > + if (ret != 0)
> > + return ret;
> > +
> > + regmap_update_bits(priv->regmap, MESON_PCIE_REG0,
> > + MESON_PCIE_POWERDOWN, 1);
> > + return 0;
> > +}
> > +
> > +static int phy_axg_pcie_init(struct phy *phy)
> > +{
> > + struct phy_axg_pcie_priv *priv = phy_get_drvdata(phy);
> > + int ret;
> > +
> > + ret = phy_init(priv->analog);
> > + if (ret != 0)
> > + return ret;
> > +
> > + regmap_write(priv->regmap, MESON_PCIE_REG0, MESON_PCIE_PHY_INIT);
> > + return reset_control_reset(priv->reset);
> > +}
> > +
> > +static int phy_axg_pcie_exit(struct phy *phy)
> > +{
> > + struct phy_axg_pcie_priv *priv = phy_get_drvdata(phy);
> > + int ret;
> > +
> > + ret = phy_exit(priv->analog);
> > + if (ret != 0)
> > + return ret;
> > +
> > + return reset_control_reset(priv->reset);
> > +}
> > +
> > +static int phy_axg_pcie_reset(struct phy *phy)
> > +{
> > + struct phy_axg_pcie_priv *priv = phy_get_drvdata(phy);
> > + int ret = 0;
> > +
> > + ret = phy_reset(priv->analog);
> > + if (ret != 0)
> > + goto out;
> > +
> > + ret = reset_control_assert(priv->reset);
> > + if (ret != 0)
> > + goto out;
> > + udelay(MESON_PCIE_RESET_DELAY);
> > +
> > + ret = reset_control_deassert(priv->reset);
> > + if (ret != 0)
> > + goto out;
> > + udelay(MESON_PCIE_RESET_DELAY);
> > +
> > +out:
> > + return ret;
> > +}
> > +
> > +static const struct phy_ops phy_axg_pcie_ops = {
> > + .init = phy_axg_pcie_init,
> > + .exit = phy_axg_pcie_exit,
> > + .power_on = phy_axg_pcie_power_on,
> > + .power_off = phy_axg_pcie_power_off,
> > + .reset = phy_axg_pcie_reset,
> > + .owner = THIS_MODULE,
> > +};
> > +
> > +static int phy_axg_pcie_probe(struct platform_device *pdev)
> > +{
> > + struct phy_provider *pphy;
> > + struct device *dev = &pdev->dev;
> > + struct phy_axg_pcie_priv *priv;
> > + struct device_node *np = dev->of_node;
> > + struct resource *res;
> > + void __iomem *base;
> > + int ret;
> > +
> > + priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL);
> > + if (!priv)
> > + return -ENOMEM;
> > +
> > + priv->phy = devm_phy_create(dev, np, &phy_axg_pcie_ops);
> > + if (IS_ERR(priv->phy)) {
> > + ret = PTR_ERR(priv->phy);
> > + if (ret != -EPROBE_DEFER)
> > + dev_err(dev, "failed to create PHY\n");
> > + return ret;
> > + }
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + base = devm_ioremap_resource(dev, res);
> > + if (IS_ERR(base))
> > + return PTR_ERR(base);
> > +
> > + priv->regmap = devm_regmap_init_mmio(dev, base,
> > + &phy_axg_pcie_regmap_conf);
> > + if (IS_ERR(priv->regmap))
> > + return PTR_ERR(priv->regmap);
> > +
> > + priv->reset = devm_reset_control_array_get(dev, false, false);
> > + if (IS_ERR(priv->reset))
> > + return PTR_ERR(priv->reset);
> > +
> > + priv->analog = devm_phy_get(dev, "analog");
> > + if (IS_ERR(priv->analog))
> > + return PTR_ERR(priv->analog);
> > +
> > + phy_set_drvdata(priv->phy, priv);
> > + dev_set_drvdata(dev, priv);
> > + pphy = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> > +
> > + return PTR_ERR_OR_ZERO(pphy);
> > +}
> > +
> > +static const struct of_device_id phy_axg_pcie_of_match[] = {
> > + {
> > + .compatible = "amlogic,axg-pcie-phy",
> > + },
> > + { },
> > +};
> > +MODULE_DEVICE_TABLE(of, phy_axg_pcie_of_match);
> > +
> > +static struct platform_driver phy_axg_pcie_driver = {
> > + .probe = phy_axg_pcie_probe,
> > + .driver = {
> > + .name = "phy-axg-pcie",
> > + .of_match_table = phy_axg_pcie_of_match,
> > + },
> > +};
> > +module_platform_driver(phy_axg_pcie_driver);
> > +
> > +MODULE_AUTHOR("Remi Pommarel <repk@...plefau.lt>");
> > +MODULE_DESCRIPTION("Amlogic AXG PCIE PHY driver");
> > +MODULE_LICENSE("GPL v2");
> >
Powered by blists - more mailing lists