| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20200407093654.26095-1-o.rempel@pengutronix.de>
Date: Tue, 7 Apr 2020 11:36:54 +0200
From: Oleksij Rempel <o.rempel@...gutronix.de>
To: Andrew Lunn <andrew@...n.ch>,
Florian Fainelli <f.fainelli@...il.com>,
Heiner Kallweit <hkallweit1@...il.com>
Cc: Oleksij Rempel <o.rempel@...gutronix.de>,
David Jander <david@...tonic.nl>,
"David S. Miller" <davem@...emloft.net>, kernel@...gutronix.de,
linux-kernel@...r.kernel.org, netdev@...r.kernel.org,
Philippe Schenker <philippe.schenker@...adex.com>,
Russell King <linux@...linux.org.uk>
Subject: [PATCH net-next v3] net: phy: micrel: add phy-mode support for the KSZ9031 PHY
Add support for following phy-modes: rgmii, rgmii-id, rgmii-txid, rgmii-rxid.
This PHY has an internal RX delay of 1.2ns and no delay for TX.
The pad skew registers allow to set the total TX delay to max 1.38ns and
the total RX delay to max of 2.58ns (configurable 1.38ns + build in
1.2ns) and a minimal delay of 0ns.
According to the RGMII v1.3 specification the delay provided by PCB traces
should be between 1.5ns and 2.0ns. The RGMII v2.0 allows to provide this
delay by MAC or PHY. So, we configure this PHY to the best values we can
get by this HW: TX delay to 1.38ns (max supported value) and RX delay to
1.80ns (best calculated delay)
The phy-modes can still be fine tuned/overwritten by *-skew-ps
device tree properties described in:
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
Signed-off-by: Oleksij Rempel <o.rempel@...gutronix.de>
---
changes v3:
- change delay on RX line to 1.80ns
- add warning if *-skew-ps properties are used together with not rgmii
mode.
changes v2:
- change RX_ID value from 0x1a to 0xa. The overflow bit was detected by
FIELD_PREP() build check.
Reported-by: kbuild test robot <lkp@...el.com>
drivers/net/phy/micrel.c | 128 +++++++++++++++++++++++++++++++++++++--
1 file changed, 123 insertions(+), 5 deletions(-)
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 05d20343b8161..045783eb4bc70 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -19,6 +19,7 @@
* ksz9477
*/
+#include <linux/bitfield.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/phy.h>
@@ -490,9 +491,50 @@ static int ksz9021_config_init(struct phy_device *phydev)
/* MMD Address 0x2 */
#define MII_KSZ9031RN_CONTROL_PAD_SKEW 4
+#define MII_KSZ9031RN_RX_CTL_M GENMASK(7, 4)
+#define MII_KSZ9031RN_TX_CTL_M GENMASK(3, 0)
+
#define MII_KSZ9031RN_RX_DATA_PAD_SKEW 5
+#define MII_KSZ9031RN_RXD3 GENMASK(15, 12)
+#define MII_KSZ9031RN_RXD2 GENMASK(11, 8)
+#define MII_KSZ9031RN_RXD1 GENMASK(7, 4)
+#define MII_KSZ9031RN_RXD0 GENMASK(3, 0)
+
#define MII_KSZ9031RN_TX_DATA_PAD_SKEW 6
+#define MII_KSZ9031RN_TXD3 GENMASK(15, 12)
+#define MII_KSZ9031RN_TXD2 GENMASK(11, 8)
+#define MII_KSZ9031RN_TXD1 GENMASK(7, 4)
+#define MII_KSZ9031RN_TXD0 GENMASK(3, 0)
+
#define MII_KSZ9031RN_CLK_PAD_SKEW 8
+#define MII_KSZ9031RN_GTX_CLK GENMASK(9, 5)
+#define MII_KSZ9031RN_RX_CLK GENMASK(4, 0)
+
+/* KSZ9031 has internal RGMII_IDRX = 1.2ns and RGMII_IDTX = 0ns. To
+ * provide different RGMII options we need to configure delay offset
+ * for each pad relative to build in delay.
+ */
+/* keep rx as "No delay adjustment" and set rx_clk to +0.60ns to get delays of
+ * 1.80ns
+ */
+#define RX_ID 0x7
+#define RX_CLK_ID 0x19
+
+/* set rx to +0.30ns and rx_clk to -0.90ns to compensate the
+ * internal 1.2ns delay.
+ */
+#define RX_ND 0xc
+#define RX_CLK_ND 0x0
+
+/* set tx to -0.42ns and tx_clk to +0.96ns to get 1.38ns delay */
+#define TX_ID 0x0
+#define TX_CLK_ID 0x1f
+
+/* set tx and tx_clk to "No delay adjustment" to keep 0ns
+ * dealy
+ */
+#define TX_ND 0x7
+#define TX_CLK_ND 0xf
/* MMD Address 0x1C */
#define MII_KSZ9031RN_EDPD 0x23
@@ -501,7 +543,8 @@ static int ksz9021_config_init(struct phy_device *phydev)
static int ksz9031_of_load_skew_values(struct phy_device *phydev,
const struct device_node *of_node,
u16 reg, size_t field_sz,
- const char *field[], u8 numfields)
+ const char *field[], u8 numfields,
+ bool *update)
{
int val[4] = {-1, -2, -3, -4};
int matches = 0;
@@ -517,6 +560,8 @@ static int ksz9031_of_load_skew_values(struct phy_device *phydev,
if (!matches)
return 0;
+ *update |= true;
+
if (matches < numfields)
newval = phy_read_mmd(phydev, 2, reg);
else
@@ -565,6 +610,67 @@ static int ksz9031_enable_edpd(struct phy_device *phydev)
reg | MII_KSZ9031RN_EDPD_ENABLE);
}
+static int ksz9031_config_rgmii_delay(struct phy_device *phydev)
+{
+ u16 rx, tx, rx_clk, tx_clk;
+ int ret;
+
+ switch (phydev->interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ tx = TX_ND;
+ tx_clk = TX_CLK_ND;
+ rx = RX_ND;
+ rx_clk = RX_CLK_ND;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ tx = TX_ID;
+ tx_clk = TX_CLK_ID;
+ rx = RX_ID;
+ rx_clk = RX_CLK_ID;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ tx = TX_ND;
+ tx_clk = TX_CLK_ND;
+ rx = RX_ID;
+ rx_clk = RX_CLK_ID;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ tx = TX_ID;
+ tx_clk = TX_CLK_ID;
+ rx = RX_ND;
+ rx_clk = RX_CLK_ND;
+ break;
+ default:
+ return 0;
+ }
+
+ ret = phy_write_mmd(phydev, 2, MII_KSZ9031RN_CONTROL_PAD_SKEW,
+ FIELD_PREP(MII_KSZ9031RN_RX_CTL_M, rx) |
+ FIELD_PREP(MII_KSZ9031RN_TX_CTL_M, tx));
+ if (ret < 0)
+ return ret;
+
+ ret = phy_write_mmd(phydev, 2, MII_KSZ9031RN_RX_DATA_PAD_SKEW,
+ FIELD_PREP(MII_KSZ9031RN_RXD3, rx) |
+ FIELD_PREP(MII_KSZ9031RN_RXD2, rx) |
+ FIELD_PREP(MII_KSZ9031RN_RXD1, rx) |
+ FIELD_PREP(MII_KSZ9031RN_RXD0, rx));
+ if (ret < 0)
+ return ret;
+
+ ret = phy_write_mmd(phydev, 2, MII_KSZ9031RN_TX_DATA_PAD_SKEW,
+ FIELD_PREP(MII_KSZ9031RN_TXD3, tx) |
+ FIELD_PREP(MII_KSZ9031RN_TXD2, tx) |
+ FIELD_PREP(MII_KSZ9031RN_TXD1, tx) |
+ FIELD_PREP(MII_KSZ9031RN_TXD0, tx));
+ if (ret < 0)
+ return ret;
+
+ return phy_write_mmd(phydev, 2, MII_KSZ9031RN_CLK_PAD_SKEW,
+ FIELD_PREP(MII_KSZ9031RN_GTX_CLK, tx_clk) |
+ FIELD_PREP(MII_KSZ9031RN_RX_CLK, rx_clk));
+}
+
static int ksz9031_config_init(struct phy_device *phydev)
{
const struct device *dev = &phydev->mdio.dev;
@@ -597,21 +703,33 @@ static int ksz9031_config_init(struct phy_device *phydev)
} while (!of_node && dev_walker);
if (of_node) {
+ bool update = false;
+
+ if (phy_interface_is_rgmii(phydev)) {
+ result = ksz9031_config_rgmii_delay(phydev);
+ if (result < 0)
+ return result;
+ }
+
ksz9031_of_load_skew_values(phydev, of_node,
MII_KSZ9031RN_CLK_PAD_SKEW, 5,
- clk_skews, 2);
+ clk_skews, 2, &update);
ksz9031_of_load_skew_values(phydev, of_node,
MII_KSZ9031RN_CONTROL_PAD_SKEW, 4,
- control_skews, 2);
+ control_skews, 2, &update);
ksz9031_of_load_skew_values(phydev, of_node,
MII_KSZ9031RN_RX_DATA_PAD_SKEW, 4,
- rx_data_skews, 4);
+ rx_data_skews, 4, &update);
ksz9031_of_load_skew_values(phydev, of_node,
MII_KSZ9031RN_TX_DATA_PAD_SKEW, 4,
- tx_data_skews, 4);
+ tx_data_skews, 4, &update);
+
+ if (update && phydev->interface != PHY_INTERFACE_MODE_RGMII)
+ phydev_warn(phydev,
+ "*-skew-ps values should be used only with phy-mode = \"rgmii\"\n");
/* Silicon Errata Sheet (DS80000691D or DS80000692D):
* When the device links in the 1000BASE-T slave mode only,
--
2.26.0.rc2
Powered by blists - more mailing lists