[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20200529030126.GW279327@builder.lan>
Date: Thu, 28 May 2020 20:01:26 -0700
From: Bjorn Andersson <bjorn.andersson@...aro.org>
To: Jonathan Marek <jonathan@...ek.ca>
Cc: linux-arm-msm@...r.kernel.org, Andy Gross <agross@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@...r.kernel.org>,
open list <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH 5/6] arm64: dts: qcom: add sm8150 hdk dts
On Sat 23 May 19:38 PDT 2020, Jonathan Marek wrote:
> Add initial HDK855 dts, based on sm8150-mtp, with a few changes.
>
Happy to see this on the list Jonathan, just some minor things on the
remoteproc nodes below.
> Signed-off-by: Jonathan Marek <jonathan@...ek.ca>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 461 ++++++++++++++++++++++++
> 2 files changed, 462 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sm8150-hdk.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index cc103f7020fd..e5dbd8b63951 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
[..]
> +/ {
> + model = "Qualcomm Technologies, Inc. SM8150 HDK";
> + compatible = "qcom,sm8150-hdk";
> +
> + aliases {
> + serial0 = &uart2;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + vph_pwr: vph-pwr-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vph_pwr";
> + regulator-min-microvolt = <3700000>;
> + regulator-max-microvolt = <3700000>;
> + };
> +
> + /*
> + * Apparently RPMh does not provide support for PM8150 S4 because it
> + * is always-on; model it as a fixed regulator.
> + */
One day we should stop being surprised by this and drop the "Apparently"
from this comment ;)
> + vreg_s4a_1p8: pm8150-s4 {
> + compatible = "regulator-fixed";
> + regulator-name = "vreg_s4a_1p8";
> +
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + regulator-always-on;
> + regulator-boot-on;
> +
> + vin-supply = <&vph_pwr>;
> + };
[..]
> +&remoteproc_adsp {
> + status = "okay";
It would be nice to see a
firmware-name = "qcom/sm8150/adsp.mbn";
here. Because if we ever end up pushing firmware to linux-firmware this
DTB would continue to work.
Use https://github.com/andersson/pil-squasher to get mbn files out of
the mdt+bXX files for your testing (or just rename/symlink the mdt to
mbn for now).
> +};
> +
> +&remoteproc_cdsp {
> + status = "okay";
firmware-name = "qcom/sm8150/cdsp.mbn";
> +};
> +
> +&remoteproc_slpi {
> + status = "okay";
firmware-name = "qcom/sm8150/slpi.mbn";
Regards,
Bjorn
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <0 4>, <126 4>;
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&ufs_mem_hc {
> + status = "okay";
> +
> + reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
> +
> + vcc-supply = <&vreg_l10a_2p5>;
> + vcc-max-microamp = <750000>;
> + vccq-supply = <&vreg_l9a_1p2>;
> + vccq-max-microamp = <700000>;
> + vccq2-supply = <&vreg_s4a_1p8>;
> + vccq2-max-microamp = <750000>;
> +};
> +
> +&ufs_mem_phy {
> + status = "okay";
> +
> + vdda-phy-supply = <&vdda_ufs_2ln_core_1>;
> + vdda-max-microamp = <90200>;
> + vdda-pll-supply = <&vreg_l3c_1p2>;
> + vdda-pll-max-microamp = <19000>;
> +};
> +
> +&usb_1_hsphy {
> + status = "okay";
> + vdda-pll-supply = <&vdd_usb_hs_core>;
> + vdda33-supply = <&vdda_usb_hs_3p1>;
> + vdda18-supply = <&vdda_usb_hs_1p8>;
> +};
> +
> +&usb_2_hsphy {
> + status = "okay";
> + vdda-pll-supply = <&vdd_usb_hs_core>;
> + vdda33-supply = <&vdda_usb_hs_3p1>;
> + vdda18-supply = <&vdda_usb_hs_1p8>;
> +};
> +
> +&usb_1_qmpphy {
> + status = "okay";
> + vdda-phy-supply = <&vreg_l3c_1p2>;
> + vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
> +};
> +
> +&usb_2_qmpphy {
> + status = "okay";
> + vdda-phy-supply = <&vreg_l3c_1p2>;
> + vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
> +};
> +
> +&usb_1 {
> + status = "okay";
> +};
> +
> +&usb_2 {
> + status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> + dr_mode = "peripheral";
> +};
> +
> +&usb_2_dwc3 {
> + dr_mode = "host";
> +};
> --
> 2.26.1
>
Powered by blists - more mailing lists