| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Wed, 30 Sep 2020 10:23:49 +0800
From: ChiYuan Huang <u0084500@...il.com>
To: Rob Herring <robh@...nel.org>
Cc: lgirdwood@...il.com, Mark Brown <broonie@...nel.org>,
linux-kernel@...r.kernel.org, cy_huang <cy_huang@...htek.com>,
devicetree@...r.kernel.org
Subject: Re: [PATCH v2 2/2] regulator: rtmv20: Add DT-binding document for
Richtek RTMV20
Hi, Rob
Ack is in below comments.
Hi, Mark:
Due to that already merged into your regulator for-next git, may I
send the patch to fix Rob's comment?
And I also found one line need to be added into rtmv20 probe phase.
Please check below.
/*
* keep in shutdown mode to minimize the current consumption
* and also mark regcache as dirty
*/
+ regcache_cache_only(priv->regmap, true);
regcache_mark_dirty(priv->regmap);
gpiod_set_value(priv->enable_gpio, 0);
Can I directly merge into one that includes Rob's comment and the
above line to be added?
Rob Herring <robh@...nel.org> 於 2020年9月29日 週二 下午11:06寫道：
>
> On Mon, Sep 28, 2020 at 03:19:44PM +0800, cy_huang wrote:
> > From: ChiYuan Huang <cy_huang@...htek.com>
> >
> > Add DT-binding document for Richtek RTMV20
> >
> > Signed-off-by: ChiYuan Huang <cy_huang@...htek.com>
> > ---
> > .../regulator/richtek,rtmv20-regulator.yaml | 168 +++++++++++++++++++++
> > 1 file changed, 168 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/regulator/richtek,rtmv20-regulator.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/regulator/richtek,rtmv20-regulator.yaml b/Documentation/devicetree/bindings/regulator/richtek,rtmv20-regulator.yaml
> > new file mode 100644
> > index 00000000..4cb4b68
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/regulator/richtek,rtmv20-regulator.yaml
> > @@ -0,0 +1,168 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/regulator/richtek,rtmv20-regulator.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Richtek RTMV20 laser diode regulator
> > +
> > +maintainers:
> > + - ChiYuan Huang <cy_huang@...htek.com>
> > +
> > +description: |
> > + Richtek RTMV20 is a load switch current regulator that can supply up to 6A.
> > + It is used to drive laser diode. There're two signals for chip controls
> > + (Enable/Fail), Enable pin to turn chip on, and Fail pin as fault indication.
> > + There're still four pins for camera control, two inputs (strobe and vsync),
> > + the others for outputs (fsin1 and fsin2). Strobe input to start the current
> > + supply, vsync input from IR camera, and fsin1/fsin2 output for the optional.
> > +
> > +properties:
> > + compatible:
> > + const: richtek,rtmv20
> > +
> > + reg:
> > + maxItems: 1
> > +
> > + wakeup-source: true
> > +
> > + interrupts-extend:
>
> You mean interrupts-extended?
>
> In any case, use 'interrupts' here and the tooling allows for either.
Yes, you're righ.
Sorry, I key in the yaml file, line by line.
It's really a typo.
>
> > + maxItems: 1
> > +
> > + enable-gpios:
> > + description: A connection of the 'enable' gpio line.
> > + maxItems: 1
> > +
> > + ld-pulse-delay-us:
> > + description: |
> > + load current pulse delay in microsecond after strobe pin pulse high.
> > + $ref: "/schemas/types.yaml#/definitions/uint32"
>
> Don't need a type ref when you have a standard property unit suffix, so
> drop.
Ack, remove type ref for all properties that included unit suffix.
>
> This and all the following need a vendor prefix too.
Is it okay to Add "richtek," prefix for all the properties except lsw
regulator node?
>
> > + minimum: 0
> > + maximum: 100000
> > + default: 0
> > +
> > + ld-pulse-width-us:
> > + description: |
> > + Load current pulse width in microsecond after strobe pin pulse high.
> > + $ref: "/schemas/types.yaml#/definitions/uint32"
> > + minimum: 0
> > + maximum: 10000
> > + default: 1200
> > +
> > + fsin1-delay-us:
> > + description: |
> > + Fsin1 pulse high delay in microsecond after vsync signal pulse high.
> > + $ref: "/schemas/types.yaml#/definitions/uint32"
> > + minimum: 0
> > + maximum: 100000
> > + default: 23000
> > +
> > + fsin1-width-us:
> > + description: |
> > + Fsin1 pulse high width in microsecond after vsync signal pulse high.
> > + $ref: "/schemas/types.yaml#/definitions/uint32"
> > + minimum: 40
> > + maximum: 10000
> > + default: 160
> > +
> > + fsin2-delay-us:
> > + description: |
> > + Fsin2 pulse high delay in microsecond after vsync signal pulse high.
> > + $ref: "/schemas/types.yaml#/definitions/uint32"
> > + minimum: 0
> > + maximum: 100000
> > + default: 23000
> > +
> > + fsin2-width-us:
> > + description: |
> > + Fsin2 pulse high width in microsecond after vsync signal pulse high.
> > + $ref: "/schemas/types.yaml#/definitions/uint32"
> > + minimum: 40
> > + maximum: 10000
> > + default: 160
> > +
> > + es-pulse-width-us:
> > + description: Eye safety function pulse width limit in microsecond.
> > + $ref: "/schemas/types.yaml#/definitions/uint32"
> > + minimum: 0
> > + maximum: 10000
> > + default: 1200
> > +
> > + es-ld-current-microamp:
> > + description: Eye safety function load current limit in microamp.
> > + $ref: "/schemas/types.yaml#/definitions/uint32"
> > + minimum: 0
> > + maximum: 6000000
> > + default: 3000000
> > +
> > + lbp-level-microvolt:
> > + description: Low battery protection level in microvolt.
> > + $ref: "/schemas/types.yaml#/definitions/uint32"
> > + minimum: 2400000
> > + maximum: 3700000
> > + default: 2700000
> > +
> > + lbp-enable:
> > + description: Low battery protection function enable control.
> > + type: boolean
> > +
> > + strobe-polarity-high:
> > + description: Strobe pin active polarity control.
> > + type: boolean
> > +
> > + vsync-polarity-high:
> > + description: Vsync pin active polarity control.
> > + type: boolean
> > +
> > + fsin-enable:
> > + description: Fsin function enable control.
> > + type: boolean
> > +
> > + fsin-output:
> > + description: Fsin function output control.
> > + type: boolean
> > +
> > + es-enable:
> > + description: Eye safety function enable control.
> > + type: boolean
> > +
> > +patternProperties:
> > + "lsw":
>
> This matches ".*lsw.*". What you wanted? If just 'lsw', then it's not a
> pattern.
>
OK
> > + type: object
> > + $ref: "regulator.yaml#"
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - wakeup-source
> > + - interrupts-extend
> > + - enable-gpios
> > + - lsw
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/interrupt-controller/irq.h>
> > + i2c {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + rtmv20@34 {
> > + compatible = "richtek,rtmv20";
> > + reg = <0x34>;
> > + wakeup-source;
> > + interrupts-extend = <&gpio26 2 IRQ_TYPE_LEVEL_LOW>;
>
> 2 wrongs make a right... But your driver interrupt probably doesn't work
> too well.
Yes, fix it right now.
>
> > + enable-gpios = <&gpio26 3 0>;
> > +
> > + strobe-polarity-high;
> > + vsync-polarity-high;
> > +
> > + lsw {
> > + regulator-name = "rtmv20,lsw";
> > + regulator-min-microamp = <0>;
> > + regulator-max-microamp = <6000000>;
> > + };
> > + };
> > + };
> > +...
> > --
> > 2.7.4
> >
Powered by blists - more mailing lists