Message-ID: <BYAPR02MB58968FCE354E8F69C417C064C1110@BYAPR02MB5896.namprd02.prod.outlook.com>
Date:   Tue, 3 Nov 2020 09:05:40 +0000
From:   Manish Narani <MNARANI@...inx.com>
To:     Manish Narani <MNARANI@...inx.com>,
        "gregkh@...uxfoundation.org" <gregkh@...uxfoundation.org>,
        "robh+dt@...nel.org" <robh+dt@...nel.org>,
        Michal Simek <michals@...inx.com>,
        "balbi@...nel.org" <balbi@...nel.org>,
        "p.zabel@...gutronix.de" <p.zabel@...gutronix.de>
CC:     "linux-usb@...r.kernel.org" <linux-usb@...r.kernel.org>,
        "devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
        "linux-arm-kernel@...ts.infradead.org" 
        <linux-arm-kernel@...ts.infradead.org>,
        "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
        git <git@...inx.com>
Subject: RE: [PATCH v3 2/2] usb: dwc3: Add driver for Xilinx platforms

Ping!

> -----Original Message-----
> From: Manish Narani <manish.narani@...inx.com>
> Sent: Thursday, October 8, 2020 6:37 PM
> To: gregkh@...uxfoundation.org; robh+dt@...nel.org; Michal Simek
> <michals@...inx.com>; balbi@...nel.org; p.zabel@...gutronix.de
> Cc: linux-usb@...r.kernel.org; devicetree@...r.kernel.org; linux-arm-
> kernel@...ts.infradead.org; linux-kernel@...r.kernel.org; git <git@...inx.com>;
> Manish Narani <MNARANI@...inx.com>
> Subject: [PATCH v3 2/2] usb: dwc3: Add driver for Xilinx platforms
> 
> Add a new driver for supporting Xilinx platforms. This driver is used
> for some sequence of operations required for Xilinx USB controllers.
> This driver is also used to choose between PIPE clock coming from SerDes
> and the Suspend Clock. Before the controller is out of reset, the clock
> selection should be changed to PIPE clock in order to make the USB
> controller work. There is a register added in Xilinx USB controller
> register space for the same.
> 
> Signed-off-by: Manish Narani <manish.narani@...inx.com>
> ---
>  drivers/usb/dwc3/Kconfig          |   9 +
>  drivers/usb/dwc3/Makefile         |   1 +
>  drivers/usb/dwc3/dwc3-of-simple.c |   1 -
>  drivers/usb/dwc3/dwc3-xilinx.c    | 334 ++++++++++++++++++++++++++++++
>  4 files changed, 344 insertions(+), 1 deletion(-)
>  create mode 100644 drivers/usb/dwc3/dwc3-xilinx.c
> 
> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
> index 7a2304565a73..0e00e6dfccd8 100644
> --- a/drivers/usb/dwc3/Kconfig
> +++ b/drivers/usb/dwc3/Kconfig
> @@ -139,4 +139,13 @@ config USB_DWC3_QCOM
>  	  for peripheral mode support.
>  	  Say 'Y' or 'M' if you have one such device.
> 
> +config USB_DWC3_XILINX
> +	tristate "Xilinx Platforms"
> +	depends on (ARCH_ZYNQMP || ARCH_VERSAL) && OF
> +	default USB_DWC3
> +	help
> +	  Support Xilinx SoCs with DesignWare Core USB3 IP.
> +	  This driver handles both ZynqMP and Versal SoC operations.
> +	  Say 'Y' or 'M' if you have one such device.
> +
>  endif
> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
> index ae86da0dc5bd..add567578b1f 100644
> --- a/drivers/usb/dwc3/Makefile
> +++ b/drivers/usb/dwc3/Makefile
> @@ -51,3 +51,4 @@ obj-$(CONFIG_USB_DWC3_MESON_G12A)	+= dwc3-
> meson-g12a.o
>  obj-$(CONFIG_USB_DWC3_OF_SIMPLE)	+= dwc3-of-simple.o
>  obj-$(CONFIG_USB_DWC3_ST)		+= dwc3-st.o
>  obj-$(CONFIG_USB_DWC3_QCOM)		+= dwc3-qcom.o
> +obj-$(CONFIG_USB_DWC3_XILINX)		+= dwc3-xilinx.o
> diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-of-
> simple.c
> index 7df115012935..e3a485b76818 100644
> --- a/drivers/usb/dwc3/dwc3-of-simple.c
> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
> @@ -172,7 +172,6 @@ static const struct dev_pm_ops
> dwc3_of_simple_dev_pm_ops = {
> 
>  static const struct of_device_id of_dwc3_simple_match[] = {
>  	{ .compatible = "rockchip,rk3399-dwc3" },
> -	{ .compatible = "xlnx,zynqmp-dwc3" },
>  	{ .compatible = "cavium,octeon-7130-usb-uctl" },
>  	{ .compatible = "sprd,sc9860-dwc3" },
>  	{ .compatible = "allwinner,sun50i-h6-dwc3" },
> diff --git a/drivers/usb/dwc3/dwc3-xilinx.c b/drivers/usb/dwc3/dwc3-xilinx.c
> new file mode 100644
> index 000000000000..7e485951d2f7
> --- /dev/null
> +++ b/drivers/usb/dwc3/dwc3-xilinx.c
> @@ -0,0 +1,334 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/**
> + * dwc3-xilinx.c - Xilinx DWC3 controller specific glue driver
> + *
> + * Authors: Manish Narani <manish.narani@...inx.com>
> + *          Anurag Kumar Vulisha <anurag.kumar.vulisha@...inx.com>
> + */
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/slab.h>
> +#include <linux/clk.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/of_platform.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/reset.h>
> +#include <linux/of_address.h>
> +#include <linux/delay.h>
> +#include <linux/firmware/xlnx-zynqmp.h>
> +#include <linux/io.h>
> +
> +#include <linux/phy/phy.h>
> +
> +/* USB phy reset mask register */
> +#define XLNX_USB_PHY_RST_EN			0x001C
> +#define XLNX_PHY_RST_MASK			0x1
> +
> +/* Xilinx USB 3.0 IP Register */
> +#define XLNX_USB_TRAFFIC_ROUTE_CONFIG		0x005C
> +#define XLNX_USB_TRAFFIC_ROUTE_FPD		0x1
> +
> +/* Versal USB Reset ID */
> +#define VERSAL_USB_RESET_ID			0xC104036
> +
> +#define XLNX_USB_FPD_PIPE_CLK			0x7c
> +#define PIPE_CLK_DESELECT			1
> +#define PIPE_CLK_SELECT				0
> +#define XLNX_USB_FPD_POWER_PRSNT		0x80
> +#define PIPE_POWER_ON				1
> +#define PIPE_POWER_OFF				0
> +
> +struct dwc3_xlnx {
> +	int				num_clocks;
> +	struct clk_bulk_data		*clks;
> +	struct device			*dev;
> +	void __iomem			*regs;
> +	int				(*pltfm_init)(struct dwc3_xlnx *data);
> +};
> +
> +static void dwc3_xlnx_mask_phy_rst(struct dwc3_xlnx *priv_data, bool mask)
> +{
> +	u32 reg;
> +
> +	/*
> +	 * Enable or disable ULPI PHY reset from USB Controller.
> +	 * This does not actually reset the phy, but just controls
> +	 * whether USB controller can or cannot reset ULPI PHY.
> +	 */
> +	reg = readl(priv_data->regs + XLNX_USB_PHY_RST_EN);
> +
> +	if (mask)
> +		reg &= ~XLNX_PHY_RST_MASK;
> +	else
> +		reg |= XLNX_PHY_RST_MASK;
> +
> +	writel(reg, priv_data->regs + XLNX_USB_PHY_RST_EN);
> +}
> +
> +static int dwc3_xlnx_init_versal(struct dwc3_xlnx *priv_data)
> +{
> +	struct device		*dev = priv_data->dev;
> +	int			ret;
> +
> +	dwc3_xlnx_mask_phy_rst(priv_data, false);
> +
> +	/* Assert and De-assert reset */
> +	ret = zynqmp_pm_reset_assert(VERSAL_USB_RESET_ID,
> +				     PM_RESET_ACTION_ASSERT);
> +	if (ret < 0) {
> +		dev_err_probe(dev, ret, "failed to assert Reset\n");
> +		return ret;
> +	}
> +
> +	ret = zynqmp_pm_reset_assert(VERSAL_USB_RESET_ID,
> +				     PM_RESET_ACTION_RELEASE);
> +	if (ret < 0) {
> +		dev_err_probe(dev, ret, "failed to De-assert Reset\n");
> +		return ret;
> +	}
> +
> +	dwc3_xlnx_mask_phy_rst(priv_data, true);
> +
> +	return 0;
> +}
> +
> +static int dwc3_xlnx_init_zynqmp(struct dwc3_xlnx *priv_data)
> +{
> +	struct device		*dev = priv_data->dev;
> +	struct reset_control	*crst, *hibrst, *apbrst;
> +	struct phy		*usb3_phy;
> +	int			ret;
> +	u32			reg;
> +
> +	crst = devm_reset_control_get_exclusive(dev, "usb_crst");
> +	if (IS_ERR(crst)) {
> +		ret = PTR_ERR(crst);
> +		dev_err_probe(dev, ret,
> +			      "failed to get core reset signal\n");
> +		goto err;
> +	}
> +
> +	hibrst = devm_reset_control_get_exclusive(dev, "usb_hibrst");
> +	if (IS_ERR(hibrst)) {
> +		ret = PTR_ERR(hibrst);
> +		dev_err_probe(dev, ret,
> +			      "failed to get hibernation reset signal\n");
> +		goto err;
> +	}
> +
> +	apbrst = devm_reset_control_get_exclusive(dev, "usb_apbrst");
> +	if (IS_ERR(apbrst)) {
> +		ret = PTR_ERR(apbrst);
> +		dev_err_probe(dev, ret,
> +			      "failed to get APB reset signal\n");
> +		goto err;
> +	}
> +
> +	ret = reset_control_assert(crst);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed to assert core reset\n");
> +		goto err;
> +	}
> +
> +	ret = reset_control_assert(hibrst);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed to assert hibernation reset\n");
> +		goto err;
> +	}
> +
> +	ret = reset_control_assert(apbrst);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed to assert APB reset\n");
> +		goto err;
> +	}
> +
> +	usb3_phy = devm_phy_get(dev, "usb3-phy");
> +
> +	ret = phy_init(usb3_phy);
> +	if (ret < 0) {
> +		phy_exit(usb3_phy);
> +		goto err;
> +	}
> +
> +	ret = reset_control_deassert(apbrst);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed to release APB reset\n");
> +		goto err;
> +	}
> +
> +	/* Set PIPE Power Present signal in FPD Power Present Register*/
> +	writel(PIPE_POWER_ON, priv_data->regs +
> XLNX_USB_FPD_POWER_PRSNT);
> +
> +	/* Set the PIPE Clock Select bit in FPD PIPE Clock register */
> +	writel(PIPE_CLK_SELECT, priv_data->regs + XLNX_USB_FPD_PIPE_CLK);
> +
> +	ret = reset_control_deassert(crst);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed to release core reset\n");
> +		goto err;
> +	}
> +
> +	ret = reset_control_deassert(hibrst);
> +	if (ret < 0) {
> +		dev_err(dev, "Failed to release hibernation reset\n");
> +		goto err;
> +	}
> +
> +	ret = phy_power_on(usb3_phy);
> +	if (ret < 0) {
> +		phy_exit(usb3_phy);
> +		goto err;
> +	}
> +
> +	/*
> +	 * This routes the USB DMA traffic to go through FPD path instead
> +	 * of reaching DDR directly. This traffic routing is needed to
> +	 * make SMMU and CCI work with USB DMA.
> +	 */
> +	if (of_dma_is_coherent(dev->of_node) || device_iommu_mapped(dev))
> {
> +		reg = readl(priv_data->regs +
> XLNX_USB_TRAFFIC_ROUTE_CONFIG);
> +		reg |= XLNX_USB_TRAFFIC_ROUTE_FPD;
> +		writel(reg, priv_data->regs +
> XLNX_USB_TRAFFIC_ROUTE_CONFIG);
> +	}
> +
> +err:
> +	return ret;
> +}
> +
> +static const struct of_device_id dwc3_xlnx_of_match[] = {
> +	{
> +		.compatible = "xlnx,zynqmp-dwc3",
> +		.data = &dwc3_xlnx_init_zynqmp,
> +	},
> +	{
> +		.compatible = "xlnx,versal-dwc3",
> +		.data = &dwc3_xlnx_init_versal,
> +	},
> +	{ /* Sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, dwc3_xlnx_of_match);
> +
> +static int dwc3_xlnx_probe(struct platform_device *pdev)
> +{
> +	struct dwc3_xlnx		*priv_data;
> +	struct device			*dev = &pdev->dev;
> +	struct device_node		*np = dev->of_node;
> +	const struct of_device_id	*match;
> +	void __iomem			*regs;
> +	int				ret;
> +
> +	priv_data = devm_kzalloc(dev, sizeof(*priv_data), GFP_KERNEL);
> +	if (!priv_data)
> +		return -ENOMEM;
> +
> +	regs = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(regs)) {
> +		ret = PTR_ERR(regs);
> +		dev_err_probe(dev, ret, "failed to map registers\n");
> +		return ret;
> +	}
> +
> +	match = of_match_node(dwc3_xlnx_of_match, pdev->dev.of_node);
> +
> +	priv_data->pltfm_init = match->data;
> +	priv_data->regs = regs;
> +	priv_data->dev = dev;
> +
> +	platform_set_drvdata(pdev, priv_data);
> +
> +	ret = devm_clk_bulk_get_all(priv_data->dev, &priv_data->clks);
> +	if (ret < 0)
> +		return ret;
> +
> +	priv_data->num_clocks = ret;
> +
> +	ret = clk_bulk_prepare_enable(priv_data->num_clocks, priv_data->clks);
> +	if (ret)
> +		return ret;
> +
> +	ret = priv_data->pltfm_init(priv_data);
> +	if (ret)
> +		goto err_clk_put;
> +
> +	ret = of_platform_populate(np, NULL, NULL, dev);
> +	if (ret)
> +		goto err_clk_put;
> +
> +	pm_runtime_set_active(dev);
> +	pm_runtime_enable(dev);
> +	pm_suspend_ignore_children(dev, false);
> +	pm_runtime_get_sync(dev);
> +
> +	return 0;
> +
> +err_clk_put:
> +	clk_bulk_disable_unprepare(priv_data->num_clocks, priv_data->clks);
> +	clk_bulk_put_all(priv_data->num_clocks, priv_data->clks);
> +
> +	return ret;
> +}
> +
> +static int dwc3_xlnx_remove(struct platform_device *pdev)
> +{
> +	struct dwc3_xlnx	*priv_data = platform_get_drvdata(pdev);
> +	struct device		*dev = &pdev->dev;
> +
> +	of_platform_depopulate(dev);
> +
> +	clk_bulk_disable_unprepare(priv_data->num_clocks, priv_data->clks);
> +	clk_bulk_put_all(priv_data->num_clocks, priv_data->clks);
> +	priv_data->num_clocks = 0;
> +
> +	pm_runtime_disable(dev);
> +	pm_runtime_put_noidle(dev);
> +	pm_runtime_set_suspended(dev);
> +
> +	return 0;
> +}
> +
> +static int __maybe_unused dwc3_xlnx_suspend_common(struct device *dev)
> +{
> +	struct dwc3_xlnx *priv_data = dev_get_drvdata(dev);
> +
> +	clk_bulk_disable(priv_data->num_clocks, priv_data->clks);
> +
> +	return 0;
> +}
> +
> +static int __maybe_unused dwc3_xlnx_resume_common(struct device *dev)
> +{
> +	struct dwc3_xlnx *priv_data = dev_get_drvdata(dev);
> +
> +	return clk_bulk_enable(priv_data->num_clocks, priv_data->clks);
> +}
> +
> +static int __maybe_unused dwc3_xlnx_runtime_idle(struct device *dev)
> +{
> +	pm_runtime_mark_last_busy(dev);
> +	pm_runtime_autosuspend(dev);
> +
> +	return 0;
> +}
> +
> +static UNIVERSAL_DEV_PM_OPS(dwc3_xlnx_dev_pm_ops,
> dwc3_xlnx_suspend_common,
> +			    dwc3_xlnx_resume_common,
> dwc3_xlnx_runtime_idle);
> +
> +static struct platform_driver dwc3_xlnx_driver = {
> +	.probe		= dwc3_xlnx_probe,
> +	.remove		= dwc3_xlnx_remove,
> +	.driver		= {
> +		.name		= "dwc3-xilinx",
> +		.of_match_table	= dwc3_xlnx_of_match,
> +		.pm		= &dwc3_xlnx_dev_pm_ops,
> +	},
> +};
> +
> +module_platform_driver(dwc3_xlnx_driver);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("Xilinx DWC3 controller specific glue driver");
> +MODULE_AUTHOR("Manish Narani <manish.narani@...inx.com>");
> +MODULE_AUTHOR("Anurag Kumar Vulisha
> <anurag.kumar.vulisha@...inx.com>");
> --
> 2.17.1

Powered by blists - more mailing lists