Date:   Wed, 25 Nov 2020 16:41:25 +0900
From:   AKASHI Takahiro <takahiro.akashi@...aro.org>
To:     ulf.hansson@...aro.org, adrian.hunter@...el.com
Cc:     linux-mmc@...r.kernel.org, linux-kernel@...r.kernel.org,
        ben.chuang@...esyslogic.com.tw, greg.tu@...esyslogic.com.tw
Subject: Re: [RFC PATCH v3.1 00/27] Add support UHS-II for GL9755

Gentle ping;

On Fri, Nov 06, 2020 at 11:26:59AM +0900, AKASHI Takahiro wrote:
> This is an interim snapshot of our next version, v4, for enabling
> UHS-II on MMC/SD.
> 
> It is focused on 'sdhci' side to address Adrian's comments regarding
> "modularising" sdhci-uhs2.c.
> The whole aim of this version is to get early feedback from Adrian (and
> others) on this issue. Without any consensus about the code structure,

Any comments so far?

-Takahiro Akashi

> it would make little sense to go further ahead on sdhci side.
> (Actually, Adrian has made no comments other than "modularising" so far.)
> 
> I heavily reworked/refactored sdhci-uhs2.c and re-organised the patch
> set to meet what I believe Adrian expects; no UHS-II related code in
> Legacy (UHS-I) code or sdhci.c.
> 
> Nevertheless, almost of all changes I made are trivial and straightforward
> in this direction, and I believe that there is no logic changed since v3
> except sdhci_uhs2_irq(), as ops->irq hook, where we must deal with UHS-II
> command sequences in addition to UHS-II errors. So I added extra handlings.
> 
> I admit that there is plenty of room for improvements (for example,
> handling host->flags), but again the focal point here is how sdhci-uhs2.c
> should be built as a module.
> 
> Please review this series (particularly Patch#8-#26 and #27) from this
> viewpoint in the first place.
> (Ben is working on 'host' side but there is no change on 'host' side
> in this submission except a minor tweak.)
> 
> Thanks,
> -Takahiro Akashi
> 
> ------ original cover letter from v3 ------
> Summary
> =======
> These patches[1] support UHS-II and fix GL9755 UHS-II compatibility.
> 
> About UHS-II, roughly deal with the following three parts:
> 1) A UHS-II detection and initialization:
> - Host setup to support UHS-II (Section 3.13.1 Host Controller Setup Sequence
>   [2]).
> - Detect a UHS-II I/F (Section 3.13.2 Card Interface Detection Sequence[2]).
> - In step(9) of Section 3.13.2 in [2], UHS-II initialization is include Section
>   3.13.3 UHS-II Card Initialization and Section 3.13.4 UHS-II Setting Register
>   Setup Sequence.
> 
> 2) Send Legacy SD command through SD-TRAN
> - Encapsulated SD packets are defined in SD-TRAN in order to ensure Legacy SD
>   compatibility and preserve Legacy SD infrastructures (Section 7.1.1 Packet
>   Types and Format Overview[3]).
> - Host issue a UHS-II CCMD packet or a UHS-II DCMD (Section 3.13.5 UHS-II
>   CCMD Packet issuing and Section 3.13.6 UHS-II DCMD Packet issuing[2]).
> 
> 3) UHS-II Interrupt
> - Except for UHS-II error interrupts, most interrupts share the original
>   interrupt registers.
> 
> Patch structure
> ===============
> patch#1-#7: for core
> patch#8-#17: for sdhci
> patch#18-#21: for GL9755
> 
> Tests
> =====
> Ran 'dd' command to evaluate the performance:
> (SanDisk UHS-II card on GL9755 controller)
>                              Read    Write
> UHS-II disabled (UHS-I): 88.3MB/s 60.7MB/s
> UHS-II enabled         :  206MB/s   80MB/s
> 
> TODO
> ====
> - replace some define with BIT macro
> 
> Reference
> =========
> [1] https://gitlab.com/ben.chuang/linux-uhs2-gl9755.git
> [2] SD Host Controller Simplified Specification 4.20
> [3] UHS-II Simplified Addendum 1.02
> 
> Changes in v3 (Jul. 10, 2020)
> * rebased to v5.8-rc4
> * add copyright notice
> * reorganize the patch set and split some commits into smaller ones
> * separate uhs-2 headers from others
> * correct wrong spellings
> * fix most of checkpatch warnings/errors
> * remove all k[cz]alloc() from the code
> * guard sdhci-uhs2 specific code with
>       'if (IS_ENABLED(CONFIG_MMC_SDHCI_UHS2))'
> * make sdhci-uhs2.c as a module
> * trivial changes, including
>   - rename back sdhci-core.c to sdhci.c
>   - allow vendor code to disable uhs2 if v4_mode == 0
>       in __sdhci_add_host()
>   - merge uhs2_power_up() into mmc_power_up()
>   - remove flag_uhs2 from mmc_attach_sd()
>   - add function descriptions to EXPORT'ed functions
>   - other minor code optimization
> 
> Changes in v2 (Jan. 9, 2020)
> * rebased to v5.5-rc5
> 
> AKASHI Takahiro (23):
>   mmc: core: UHS-II support, modify power-up sequence
>   mmc: core: UHS-II support, skip set_chip_select()
>   mmc: core: UHS-II support, skip TMODE setup in some cases
>   mmc: core: UHS-II support, generate UHS-II SD command packet
>   mmc: core: UHS-II support, set APP_CMD bit if necessary
>   mmc: sdhci: add a kernel configuration for enabling UHS-II support
>   mmc: sdhci: add UHS-II related definitions in headers
>   mmc: sdhci: add UHS-II module
>   mmc: sdhci-uhs2: dump UHS-II registers
>   mmc: sdhci-uhs2: add reset function
>   mmc: sdhci-uhs2: add set_power() to support vdd2
>   mmc: sdhci-uhs2: skip signal_voltage_switch()
>   mmc: sdhci-uhs2: add set_timeout()
>   mmc: sdhci-uhs2: add set_ios()
>   mmc: sdhci-uhs2: add detect_init() to detect the interface
>   mmc: sdhci-uhs2: add clock operations
>   mmc: sdhci-uhs2: add set_reg() to initialise the interface
>   mmc: sdhci-uhs2: add request() and others
>   mmc: sdhci-uhs2: add irq() and others
>   mmc: sdhci-uhs2: add add_host() and others to set up the driver
>   mmc: core: add post-mmc_attach_sd hook
>   mmc: sdhci-pci: add UHS-II support framework
>   mmc: sdhci-pci-gli: enable UHS-II mode for GL9755
> 
> Ben Chuang (4):
>   mmc: add UHS-II related definitions in public headers
>   mmc: core: UHS-II support, try to select UHS-II interface
>   mmc: sdhci-uhs2: add pre-detect_init hook
>   mmc: sdhci-uhs2: add post-mmc_attach_sd hook
> 
>  drivers/mmc/core/Makefile         |    2 +-
>  drivers/mmc/core/block.c          |    7 +-
>  drivers/mmc/core/bus.c            |    5 +-
>  drivers/mmc/core/core.c           |  118 +-
>  drivers/mmc/core/regulator.c      |   14 +
>  drivers/mmc/core/sd.c             |   32 +
>  drivers/mmc/core/sd_ops.c         |   12 +
>  drivers/mmc/core/uhs2.c           |  883 +++++++++++++++
>  drivers/mmc/core/uhs2.h           |   21 +
>  drivers/mmc/host/Kconfig          |   10 +
>  drivers/mmc/host/Makefile         |    1 +
>  drivers/mmc/host/sdhci-pci-core.c |   16 +-
>  drivers/mmc/host/sdhci-pci-gli.c  |  318 +++++-
>  drivers/mmc/host/sdhci-pci.h      |    3 +
>  drivers/mmc/host/sdhci-uhs2.c     | 1697 +++++++++++++++++++++++++++++
>  drivers/mmc/host/sdhci-uhs2.h     |  224 ++++
>  drivers/mmc/host/sdhci.c          |  333 +++---
>  drivers/mmc/host/sdhci.h          |  117 +-
>  include/linux/mmc/card.h          |    1 +
>  include/linux/mmc/core.h          |    6 +
>  include/linux/mmc/host.h          |   31 +
>  include/linux/mmc/uhs2.h          |  268 +++++
>  22 files changed, 3961 insertions(+), 158 deletions(-)
>  create mode 100644 drivers/mmc/core/uhs2.c
>  create mode 100644 drivers/mmc/core/uhs2.h
>  create mode 100644 drivers/mmc/host/sdhci-uhs2.c
>  create mode 100644 drivers/mmc/host/sdhci-uhs2.h
>  create mode 100644 include/linux/mmc/uhs2.h
> 
> -- 
> 2.28.0
> 

Powered by blists - more mailing lists