Message-Id: <1609124381-9107-1-git-send-email-zhangqing@loongson.cn>
Date:   Mon, 28 Dec 2020 10:59:38 +0800
From:   Qing Zhang <zhangqing@...ngson.cn>
To:     Mark Brown <broonie@...nel.org>, Rob Herring <robh+dt@...nel.org>,
        ThomasBogendoerfer <tsbogend@...ha.franken.de>
Cc:     linux-spi@...r.kernel.org, Huacai Chen <chenhc@...ote.com>,
        Jiaxun Yang <jiaxun.yang@...goat.com>, yangtiezhu@...ngson.cn,
        devicetree@...r.kernel.org, linux-mips@...r.kernel.org,
        linux-kernel@...r.kernel.org
Subject: [PATCH v6 1/4] spi: LS7A: Add Loongson LS7A SPI controller driver support

The SPI controller has the following characteristics:

- Full-duplex synchronous serial data transmission
- Support up to 4 variable length byte transmission
- Main mode support
- Mode failure generates an error flag and issues an interrupt request
- Double buffer receiver
- Serial clock with programmable polarity and phase
- SPI can be controlled in wait mode
- Support boot from SPI

Use mtd_debug tool to earse/write/read /dev/mtd0 on development.

eg:

[root@...ux mtd-utils-1.0.0]# mtd_debug erase /dev/mtd0 0x20000 0x40000
Erased 262144 bytes from address 0x00020000 in flash
[root@...ux mtd-utils-1.0.0]# mtd_debug write /dev/mtd0 0x20000 13 1.img
Copied 13 bytes from 1.img to address 0x00020000 in flash
[root@...ux mtd-utils-1.0.0]# mtd_debug read /dev/mtd0 0x20000 13 2.img
Copied 13 bytes from address 0x00020000 in flash to 2.img
[root@...ux mtd-utils-1.0.0]# cmp -l 1.img 2.img

Signed-off-by: Qing Zhang <zhangqing@...ngson.cn>
---

v2:
- keep Kconfig and Makefile sorted
- make the entire comment a C++ one so things look more intentional
- Fix unclear indentation
- make conditional statements to improve legibility
- Don't use static inline
- the core handle message queue
- Add a new binding document
- Fix probe part mixed pdev and PCI

v3:
- expose set_cs to the core and let it handle things
- replace transfer_one_message to transfer_one
- replace spi_alloc_master to devm_spi_alloc_master
- split out into prepare/unprepare_message
- releases pci regions before unregister master

v4:
- names used in the manual
- rename ls7a_spi_do_transfer to ls7a_spi_setup_transfer
- change read the spcr and sper outside of this function
- mode configuration moved to prepare instead
- remove redundancy code about unprepare/prepare_message
- used 0x4 instead of 0x1,WFEMPTY instead of RFEMPTY

v5:
- remove unnecessary blank lines

v6:
- keep blank line before the last "return xxx"

---
 drivers/spi/Kconfig    |   7 ++
 drivers/spi/Makefile   |   1 +
 drivers/spi/spi-ls7a.c | 282 +++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 290 insertions(+)
 create mode 100644 drivers/spi/spi-ls7a.c

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index aadaea0..af7c0d4 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -413,6 +413,13 @@ config SPI_LP8841_RTC
 	  Say N here unless you plan to run the kernel on an ICP DAS
 	  LP-8x4x industrial computer.
 
+config SPI_LS7A
+	tristate "Loongson LS7A SPI Controller Support"
+	depends on CPU_LOONGSON64 || COMPILE_TEST
+	help
+	  This drivers supports the Loongson LS7A SPI controller in master
+	  SPI mode.
+
 config SPI_MPC52xx
 	tristate "Freescale MPC52xx SPI (non-PSC) controller support"
 	depends on PPC_MPC52xx
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 6fea582..d015cf2 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -61,6 +61,7 @@ obj-$(CONFIG_SPI_LANTIQ_SSC)		+= spi-lantiq-ssc.o
 obj-$(CONFIG_SPI_JCORE)			+= spi-jcore.o
 obj-$(CONFIG_SPI_LM70_LLP)		+= spi-lm70llp.o
 obj-$(CONFIG_SPI_LP8841_RTC)		+= spi-lp8841-rtc.o
+obj-$(CONFIG_SPI_LS7A)			+= spi-ls7a.o
 obj-$(CONFIG_SPI_MESON_SPICC)		+= spi-meson-spicc.o
 obj-$(CONFIG_SPI_MESON_SPIFC)		+= spi-meson-spifc.o
 obj-$(CONFIG_SPI_MPC512x_PSC)		+= spi-mpc512x-psc.o
diff --git a/drivers/spi/spi-ls7a.c b/drivers/spi/spi-ls7a.c
new file mode 100644
index 0000000..8592b85
--- /dev/null
+++ b/drivers/spi/spi-ls7a.c
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: GPL-2.0-only
+//
+// Loongson LS7A SPI Controller driver
+//
+// Copyright (C) 2020 Loongson Technology Corporation Limited.
+//
+
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/spi/spi.h>
+
+/* define spi register */
+#define	SPCR		0x00
+#define	SPSR		0x01
+#define	FIFO		0x02
+#define	SPER		0x03
+#define	SFC_PARAM	0x04
+#define	SFC_SOFTCS	0x05
+#define	SFC_TIMING	0x06
+
+struct ls7a_spi {
+	struct spi_master *master;
+	void __iomem *base;
+	unsigned int hz;
+	unsigned int mode;
+};
+
+static void ls7a_spi_write_reg(struct ls7a_spi *spi,
+			       unsigned char reg,
+			       unsigned char data)
+{
+	writeb(data, spi->base + reg);
+}
+
+static char ls7a_spi_read_reg(struct ls7a_spi *spi, unsigned char reg)
+{
+	return readb(spi->base + reg);
+}
+
+static int ls7a_spi_prepare_message(struct spi_master *master,
+				    struct spi_message *msg)
+{
+	struct ls7a_spi *ls7a_spi;
+	struct spi_device *spi = msg->spi;
+	unsigned char val;
+
+	ls7a_spi = spi_master_get_devdata(master);
+
+	if (ls7a_spi->mode != spi->mode) {
+		val = ls7a_spi_read_reg(ls7a_spi, SPCR);
+		val &= ~0xc;
+		if (spi->mode & SPI_CPOL)
+			val |= 8;
+		if (spi->mode & SPI_CPHA)
+			val |= 4;
+		ls7a_spi_write_reg(ls7a_spi, SPCR, val);
+		val = ls7a_spi_read_reg(ls7a_spi, SPER);
+		ls7a_spi_write_reg(ls7a_spi, SPER, val);
+		ls7a_spi->mode = spi->mode;
+	}
+
+	return 0;
+}
+
+static void ls7a_spi_set_cs(struct spi_device *spi, bool enable)
+{
+	struct ls7a_spi *ls7a_spi;
+	int cs;
+
+	ls7a_spi = spi_master_get_devdata(spi->master);
+
+	cs = ls7a_spi_read_reg(ls7a_spi, SFC_SOFTCS) & ~(0x11 << spi->chip_select);
+
+	if (!!(spi->mode & SPI_CS_HIGH) == enable)
+		ls7a_spi_write_reg(ls7a_spi, SFC_SOFTCS, (0x1 << spi->chip_select) | cs);
+	else
+		ls7a_spi_write_reg(ls7a_spi, SFC_SOFTCS, (0x11 << spi->chip_select) | cs);
+}
+
+static int ls7a_spi_setup_transfer(struct spi_device *spi,
+				   struct spi_transfer *t)
+{
+	unsigned int hz;
+	unsigned int div, div_tmp;
+	unsigned int bit;
+	unsigned long clk;
+	unsigned char val;
+	unsigned char spcr, sper;
+	const char rdiv[12] = {0, 1, 4, 2, 3, 5, 6, 7, 8, 9, 10, 11};
+	struct ls7a_spi *ls7a_spi;
+
+	ls7a_spi = spi_master_get_devdata(spi->master);
+
+	if (t) {
+		hz = t->speed_hz;
+		if (!hz)
+			hz = spi->max_speed_hz;
+	} else {
+		hz = spi->max_speed_hz;
+	}
+
+	if (hz & (ls7a_spi->hz != hz)) {
+		clk = 100000000;
+
+		div = DIV_ROUND_UP(clk, hz);
+		if (div < 2)
+			div = 2;
+		if (div > 4096)
+			div = 4096;
+
+		bit = fls(div) - 1;
+		if ((1 << bit) == div)
+			bit--;
+		div_tmp = rdiv[bit];
+
+		dev_dbg(&spi->dev, "clk = %ld hz = %d div_tmp = %d bit = %d\n",
+			clk, hz, div_tmp, bit);
+
+		ls7a_spi->hz = hz;
+		spcr = div_tmp & 3;
+		sper = (div_tmp >> 2) & 3;
+
+		val = ls7a_spi_read_reg(ls7a_spi, SPCR);
+		ls7a_spi_write_reg(ls7a_spi, SPCR, (val & ~3) | spcr);
+		val = ls7a_spi_read_reg(ls7a_spi, SPER);
+		ls7a_spi_write_reg(ls7a_spi, SPER, (val & ~3) | sper);
+	}
+
+	return 0;
+}
+
+static int ls7a_spi_setup(struct spi_device *spi)
+{
+	return	ls7a_spi_setup_transfer(spi, NULL);
+}
+
+static int ls7a_spi_write_read_8bit(struct spi_device *spi,
+				    const u8 **tx_buf, u8 **rx_buf,
+				    unsigned int num)
+{
+	struct ls7a_spi *ls7a_spi;
+
+	ls7a_spi = spi_master_get_devdata(spi->master);
+
+	if (tx_buf && *tx_buf) {
+		ls7a_spi_write_reg(ls7a_spi, FIFO, *((*tx_buf)++));
+
+		while ((ls7a_spi_read_reg(ls7a_spi, SPSR) & 0x4) == 1)
+			;
+	} else {
+		ls7a_spi_write_reg(ls7a_spi, FIFO, 0);
+
+		while ((ls7a_spi_read_reg(ls7a_spi, SPSR) & 0x1) == 1)
+			;
+	}
+
+	if (rx_buf && *rx_buf)
+		*(*rx_buf)++ = ls7a_spi_read_reg(ls7a_spi, FIFO);
+	else
+		ls7a_spi_read_reg(ls7a_spi, FIFO);
+
+	return 1;
+}
+
+static unsigned int ls7a_spi_write_read(struct spi_device *spi,
+					struct spi_transfer *xfer)
+{
+	unsigned int count;
+	const u8 *tx = xfer->tx_buf;
+	u8 *rx = xfer->rx_buf;
+
+	count = xfer->len;
+
+	do {
+		if (ls7a_spi_write_read_8bit(spi, &tx, &rx, count) < 0)
+			goto out;
+		count--;
+	} while (count);
+
+out:
+	return xfer->len - count;
+}
+
+static int  ls7a_spi_transfer_one(struct spi_master *master,
+				  struct spi_device *spi,
+				  struct spi_transfer *t)
+{
+	int status = 0;
+
+	status = ls7a_spi_setup_transfer(spi, t);
+	if (status < 0)
+		return status;
+
+	if (t->len)
+		ls7a_spi_write_read(spi, t);
+
+	return status;
+}
+
+static int ls7a_spi_pci_probe(struct pci_dev *pdev,
+			      const struct pci_device_id *ent)
+{
+	struct spi_master *master;
+	struct ls7a_spi *spi;
+	int ret;
+
+	master = devm_spi_alloc_master(&pdev->dev, sizeof(*spi));
+	if (!master)
+		return -ENOMEM;
+
+	spi = spi_master_get_devdata(master);
+	ret = pcim_enable_device(pdev);
+	if (ret)
+		goto err_free_master;
+
+	ret = pci_request_regions(pdev, "ls7a-spi");
+	if (ret)
+		goto err_free_master;
+
+	spi->base = pcim_iomap(pdev, 0, pci_resource_len(pdev, 0));
+	if (!spi->base) {
+		ret = -EINVAL;
+		goto err_free_master;
+	}
+	ls7a_spi_write_reg(spi, SPCR, 0x51);
+	ls7a_spi_write_reg(spi, SPER, 0x00);
+	ls7a_spi_write_reg(spi, SFC_TIMING, 0x01);
+	ls7a_spi_write_reg(spi, SFC_PARAM, 0x40);
+	spi->mode = 0;
+
+	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+	master->set_cs = ls7a_spi_set_cs;
+	master->prepare_message = ls7a_spi_prepare_message;
+	master->setup = ls7a_spi_setup;
+	master->transfer_one = ls7a_spi_transfer_one;
+	master->bits_per_word_mask = SPI_BPW_MASK(8);
+	master->num_chipselect = 4;
+	master->dev.of_node = pdev->dev.of_node;
+
+	spi->master = master;
+
+	pci_set_drvdata(pdev, master);
+
+	ret = spi_register_master(master);
+	if (ret)
+		goto err_free_master;
+
+	return 0;
+
+err_free_master:
+	pci_release_regions(pdev);
+	return ret;
+}
+
+static void ls7a_spi_pci_remove(struct pci_dev *pdev)
+{
+	struct spi_master *master = pci_get_drvdata(pdev);
+
+	spi_unregister_master(master);
+	pci_release_regions(pdev);
+}
+
+static const struct pci_device_id ls7a_spi_pci_id_table[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a0b) },
+	{ 0, }
+};
+
+MODULE_DEVICE_TABLE(pci, ls7a_spi_pci_id_table);
+
+static struct pci_driver ls7a_spi_pci_driver = {
+	.name		= "ls7a-spi",
+	.id_table	= ls7a_spi_pci_id_table,
+	.probe		= ls7a_spi_pci_probe,
+	.remove		= ls7a_spi_pci_remove,
+};
+
+module_pci_driver(ls7a_spi_pci_driver);
+
+MODULE_AUTHOR("Juxin Gao <gaojuxin@...ngson.cn>");
+MODULE_AUTHOR("Qing Zhang <zhangqing@...ngson.cn>");
+MODULE_DESCRIPTION("Loongson LS7A SPI controller driver");
+MODULE_LICENSE("GPL v2");
-- 
2.1.0

Powered by blists - more mailing lists