| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20210310161924.22256-4-a-govindraju@ti.com>
Date: Wed, 10 Mar 2021 21:49:23 +0530
From: Aswath Govindraju <a-govindraju@...com>
To: unlisted-recipients:; (no To-header on input)
CC: Vignesh Raghavendra <vigneshr@...com>,
Lokesh Vutla <lokeshvutla@...com>,
Kishon Vijay Abraham I <kishon@...com>,
<a-govindraju@...com>, Nishanth Menon <nm@...com>,
Tero Kristo <kristo@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>
Subject: [PATCH v5 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems
The following speed modes are now supported in J7200 SoC,
- HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
- UHS-I speed modes in MMCSD1 subsystem [1].
Add support for UHS-I modes by adding voltage regulator device tree nodes
and corresponding pinmux details, to power cycle and voltage switch cards.
Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
device tree nodes.
Also update the delay values for various speed modes supported, based on
the latest J7200 datasheet[2]
[1] - section 12.3.6.1.1 MMCSD Features, in
https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf
[2] - https://www.ti.com/lit/ds/symlink/dra821a.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@...com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 42 +++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 14 ++++++-
2 files changed, 54 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index b493f939b09a..6f90c3b1cf45 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -16,6 +16,29 @@
stdout-path = "serial2:115200n8";
bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
};
+
+ vdd_mmc1: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpios = <&exp2 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: gpio-regulator-vdd-sd-dv {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd_sd_dv";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0
+ 3300000 0x1>;
+ };
};
&wkup_pmx0 {
@@ -45,6 +68,13 @@
};
&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
+ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
+ >;
+ };
+
main_i2c1_pins_default: main-i2c1-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
@@ -70,6 +100,12 @@
J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>;
};
+
+ vdd_sd_dv_pins_default: vdd_sd_dv_pins_default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+ >;
+ };
};
&wkup_uart0 {
@@ -157,6 +193,10 @@
};
&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
exp1: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
@@ -206,6 +246,8 @@
/* SD card */
pinctrl-0 = <&main_mmc1_pins_default>;
pinctrl-names = "default";
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
ti,driver-strength-ohm = <50>;
disable-wp;
};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index e60650a62b14..f86c493a44f1 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -512,11 +512,16 @@
ti,otap-del-sel-mmc-hs = <0x0>;
ti,otap-del-sel-ddr52 = <0x6>;
ti,otap-del-sel-hs200 = <0x8>;
- ti,otap-del-sel-hs400 = <0x0>;
+ ti,otap-del-sel-hs400 = <0x5>;
+ ti,itap-del-sel-legacy = <0x10>;
+ ti,itap-del-sel-mmc-hs = <0xa>;
ti,strobe-sel = <0x77>;
+ ti,clkbuf-sel = <0x7>;
ti,trm-icp = <0x8>;
bus-width = <8>;
mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
dma-coherent;
};
@@ -534,7 +539,12 @@
ti,otap-del-sel-sdr50 = <0xc>;
ti,otap-del-sel-sdr104 = <0x5>;
ti,otap-del-sel-ddr50 = <0xc>;
- no-1-8-v;
+ ti,itap-del-sel-legacy = <0x0>;
+ ti,itap-del-sel-sd-hs = <0x0>;
+ ti,itap-del-sel-sdr12 = <0x0>;
+ ti,itap-del-sel-sdr25 = <0x0>;
+ ti,clkbuf-sel = <0x7>;
+ ti,trm-icp = <0x8>;
dma-coherent;
};
--
2.17.1
Powered by blists - more mailing lists