Message-Id: <20210415121455.39536-1-clemens.gruber@pqgruber.com>
Date:   Thu, 15 Apr 2021 14:14:48 +0200
From:   Clemens Gruber <clemens.gruber@...ruber.com>
To:     linux-pwm@...r.kernel.org
Cc:     Thierry Reding <thierry.reding@...il.com>,
        Sven Van Asbroeck <TheSven73@...il.com>,
        Uwe Kleine-König 
        <u.kleine-koenig@...gutronix.de>, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org,
        Clemens Gruber <clemens.gruber@...ruber.com>
Subject: [PATCH v9 1/8] pwm: pca9685: Switch to atomic API

The switch to the atomic API goes hand in hand with a few fixes to
previously experienced issues:
- The duty cycle is no longer lost after disable/enable (previously the
  OFF registers were cleared in disable and the user was required to
  call config to restore the duty cycle settings)
- If one sets a period resulting in the same prescale register value,
  the sleep and write to the register is now skipped
- Previously, only the full ON bit was toggled in GPIO mode (and full
  OFF cleared if set to high), which could result in both full OFF and
  full ON not being set and on=0, off=0, which is not allowed according
  to the datasheet
- The OFF registers were reset to 0 in probe, which could lead to the
  forbidden on=0, off=0. Fixed by resetting to POR default (full OFF)

Signed-off-by: Clemens Gruber <clemens.gruber@...ruber.com>
---
Changes since v8:
- Revert to DIV_ROUND_UP (keep math as-is)
- Readability improvement for failed regmap_read

Changes since v7:
- Moved check for !state->enabled before prescaler configuration
- Removed unnecessary cast
- Use DIV_ROUND_DOWN in .apply

Changes since v6:
- Order of a comparison switched for improved readability

Changes since v5:
- Function documentation for set_duty
- Variable initializations
- Print warning if all LEDs channel
- Changed EOPNOTSUPP to EINVAL
- Improved error messages
- Register reset corrections moved to this patch

Changes since v4:
- Patches split up
- Use a single set_duty function
- Improve readability / new macros
- Added a patch to restrict prescale changes to the first user

Changes since v3:
- Refactoring: Extracted common functions
- Read prescale register value instead of caching it
- Return all zeros and disabled for "all LEDs" channel state
- Improved duty calculation / mapping to 0..4096

Changes since v2:
- Always set default prescale value in probe
- Simplified probe code
- Inlined functions with one callsite

Changes since v1:
- Fixed a logic error
- Impoved PM runtime handling and fixed !CONFIG_PM
- Write default prescale reg value if invalid in probe
- Reuse full_off/_on functions throughout driver
- Use cached prescale value whenever possible

 drivers/pwm/pwm-pca9685.c | 261 +++++++++++++-------------------------
 1 file changed, 91 insertions(+), 170 deletions(-)

diff --git a/drivers/pwm/pwm-pca9685.c b/drivers/pwm/pwm-pca9685.c
index 4a55dc18656c..ea19d72e5c34 100644
--- a/drivers/pwm/pwm-pca9685.c
+++ b/drivers/pwm/pwm-pca9685.c
@@ -51,7 +51,6 @@
 #define PCA9685_PRESCALE_MAX	0xFF	/* => min. frequency of 24 Hz */
 
 #define PCA9685_COUNTER_RANGE	4096
-#define PCA9685_DEFAULT_PERIOD	5000000	/* Default period_ns = 1/200 Hz */
 #define PCA9685_OSC_CLOCK_MHZ	25	/* Internal oscillator with 25 MHz */
 
 #define PCA9685_NUMREGS		0xFF
@@ -71,10 +70,14 @@
 #define LED_N_OFF_H(N)	(PCA9685_LEDX_OFF_H + (4 * (N)))
 #define LED_N_OFF_L(N)	(PCA9685_LEDX_OFF_L + (4 * (N)))
 
+#define REG_ON_H(C)	((C) >= PCA9685_MAXCHAN ? PCA9685_ALL_LED_ON_H : LED_N_ON_H((C)))
+#define REG_ON_L(C)	((C) >= PCA9685_MAXCHAN ? PCA9685_ALL_LED_ON_L : LED_N_ON_L((C)))
+#define REG_OFF_H(C)	((C) >= PCA9685_MAXCHAN ? PCA9685_ALL_LED_OFF_H : LED_N_OFF_H((C)))
+#define REG_OFF_L(C)	((C) >= PCA9685_MAXCHAN ? PCA9685_ALL_LED_OFF_L : LED_N_OFF_L((C)))
+
 struct pca9685 {
 	struct pwm_chip chip;
 	struct regmap *regmap;
-	int period_ns;
 #if IS_ENABLED(CONFIG_GPIOLIB)
 	struct mutex lock;
 	struct gpio_chip gpio;
@@ -87,6 +90,53 @@ static inline struct pca9685 *to_pca(struct pwm_chip *chip)
 	return container_of(chip, struct pca9685, chip);
 }
 
+/* Helper function to set the duty cycle ratio to duty/4096 (e.g. duty=2048 -> 50%) */
+static void pca9685_pwm_set_duty(struct pca9685 *pca, int channel, unsigned int duty)
+{
+	if (duty == 0) {
+		/* Set the full OFF bit, which has the highest precedence */
+		regmap_write(pca->regmap, REG_OFF_H(channel), LED_FULL);
+	} else if (duty >= PCA9685_COUNTER_RANGE) {
+		/* Set the full ON bit and clear the full OFF bit */
+		regmap_write(pca->regmap, REG_ON_H(channel), LED_FULL);
+		regmap_write(pca->regmap, REG_OFF_H(channel), 0);
+	} else {
+		/* Set OFF time (clears the full OFF bit) */
+		regmap_write(pca->regmap, REG_OFF_L(channel), duty & 0xff);
+		regmap_write(pca->regmap, REG_OFF_H(channel), (duty >> 8) & 0xf);
+		/* Clear the full ON bit */
+		regmap_write(pca->regmap, REG_ON_H(channel), 0);
+	}
+}
+
+static unsigned int pca9685_pwm_get_duty(struct pca9685 *pca, int channel)
+{
+	unsigned int off_h = 0, val = 0;
+
+	if (WARN_ON(channel >= PCA9685_MAXCHAN)) {
+		/* HW does not support reading state of "all LEDs" channel */
+		return 0;
+	}
+
+	regmap_read(pca->regmap, LED_N_OFF_H(channel), &off_h);
+	if (off_h & LED_FULL) {
+		/* Full OFF bit is set */
+		return 0;
+	}
+
+	regmap_read(pca->regmap, LED_N_ON_H(channel), &val);
+	if (val & LED_FULL) {
+		/* Full ON bit is set */
+		return PCA9685_COUNTER_RANGE;
+	}
+
+	if (regmap_read(pca->regmap, LED_N_OFF_L(channel), &val)) {
+		/* Reset val to 0 in case reading LED_N_OFF_L failed */
+		val = 0;
+	}
+	return ((off_h & 0xf) << 8) | (val & 0xff);
+}
+
 #if IS_ENABLED(CONFIG_GPIOLIB)
 static bool pca9685_pwm_test_and_set_inuse(struct pca9685 *pca, int pwm_idx)
 {
@@ -138,34 +188,23 @@ static int pca9685_pwm_gpio_request(struct gpio_chip *gpio, unsigned int offset)
 static int pca9685_pwm_gpio_get(struct gpio_chip *gpio, unsigned int offset)
 {
 	struct pca9685 *pca = gpiochip_get_data(gpio);
-	struct pwm_device *pwm = &pca->chip.pwms[offset];
-	unsigned int value;
 
-	regmap_read(pca->regmap, LED_N_ON_H(pwm->hwpwm), &value);
-
-	return value & LED_FULL;
+	return pca9685_pwm_get_duty(pca, offset) != 0;
 }
 
 static void pca9685_pwm_gpio_set(struct gpio_chip *gpio, unsigned int offset,
 				 int value)
 {
 	struct pca9685 *pca = gpiochip_get_data(gpio);
-	struct pwm_device *pwm = &pca->chip.pwms[offset];
-	unsigned int on = value ? LED_FULL : 0;
-
-	/* Clear both OFF registers */
-	regmap_write(pca->regmap, LED_N_OFF_L(pwm->hwpwm), 0);
-	regmap_write(pca->regmap, LED_N_OFF_H(pwm->hwpwm), 0);
 
-	/* Set the full ON bit */
-	regmap_write(pca->regmap, LED_N_ON_H(pwm->hwpwm), on);
+	pca9685_pwm_set_duty(pca, offset, value ? PCA9685_COUNTER_RANGE : 0);
 }
 
 static void pca9685_pwm_gpio_free(struct gpio_chip *gpio, unsigned int offset)
 {
 	struct pca9685 *pca = gpiochip_get_data(gpio);
 
-	pca9685_pwm_gpio_set(gpio, offset, 0);
+	pca9685_pwm_set_duty(pca, offset, 0);
 	pm_runtime_put(pca->chip.dev);
 	pca9685_pwm_clear_inuse(pca, offset);
 }
@@ -246,167 +285,52 @@ static void pca9685_set_sleep_mode(struct pca9685 *pca, bool enable)
 	}
 }
 
-static int pca9685_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
-			      int duty_ns, int period_ns)
+static int pca9685_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+			     const struct pwm_state *state)
 {
 	struct pca9685 *pca = to_pca(chip);
-	unsigned long long duty;
-	unsigned int reg;
-	int prescale;
-
-	if (period_ns != pca->period_ns) {
-		prescale = DIV_ROUND_CLOSEST(PCA9685_OSC_CLOCK_MHZ * period_ns,
-					     PCA9685_COUNTER_RANGE * 1000) - 1;
-
-		if (prescale >= PCA9685_PRESCALE_MIN &&
-			prescale <= PCA9685_PRESCALE_MAX) {
-			/*
-			 * Putting the chip briefly into SLEEP mode
-			 * at this point won't interfere with the
-			 * pm_runtime framework, because the pm_runtime
-			 * state is guaranteed active here.
-			 */
-			/* Put chip into sleep mode */
-			pca9685_set_sleep_mode(pca, true);
-
-			/* Change the chip-wide output frequency */
-			regmap_write(pca->regmap, PCA9685_PRESCALE, prescale);
-
-			/* Wake the chip up */
-			pca9685_set_sleep_mode(pca, false);
-
-			pca->period_ns = period_ns;
-		} else {
-			dev_err(chip->dev,
-				"prescaler not set: period out of bounds!\n");
-			return -EINVAL;
-		}
-	}
+	unsigned long long duty, prescale;
+	unsigned int val = 0;
 
-	if (duty_ns < 1) {
-		if (pwm->hwpwm >= PCA9685_MAXCHAN)
-			reg = PCA9685_ALL_LED_OFF_H;
-		else
-			reg = LED_N_OFF_H(pwm->hwpwm);
+	if (state->polarity != PWM_POLARITY_NORMAL)
+		return -EINVAL;
 
-		regmap_write(pca->regmap, reg, LED_FULL);
-
-		return 0;
+	prescale = DIV_ROUND_CLOSEST_ULL(PCA9685_OSC_CLOCK_MHZ * state->period,
+					 PCA9685_COUNTER_RANGE * 1000) - 1;
+	if (prescale < PCA9685_PRESCALE_MIN || prescale > PCA9685_PRESCALE_MAX) {
+		dev_err(chip->dev, "pwm not changed: period out of bounds!\n");
+		return -EINVAL;
 	}
 
-	if (duty_ns == period_ns) {
-		/* Clear both OFF registers */
-		if (pwm->hwpwm >= PCA9685_MAXCHAN)
-			reg = PCA9685_ALL_LED_OFF_L;
-		else
-			reg = LED_N_OFF_L(pwm->hwpwm);
-
-		regmap_write(pca->regmap, reg, 0x0);
-
-		if (pwm->hwpwm >= PCA9685_MAXCHAN)
-			reg = PCA9685_ALL_LED_OFF_H;
-		else
-			reg = LED_N_OFF_H(pwm->hwpwm);
-
-		regmap_write(pca->regmap, reg, 0x0);
-
-		/* Set the full ON bit */
-		if (pwm->hwpwm >= PCA9685_MAXCHAN)
-			reg = PCA9685_ALL_LED_ON_H;
-		else
-			reg = LED_N_ON_H(pwm->hwpwm);
-
-		regmap_write(pca->regmap, reg, LED_FULL);
-
+	if (!state->enabled) {
+		pca9685_pwm_set_duty(pca, pwm->hwpwm, 0);
 		return 0;
 	}
 
-	duty = PCA9685_COUNTER_RANGE * (unsigned long long)duty_ns;
-	duty = DIV_ROUND_UP_ULL(duty, period_ns);
-
-	if (pwm->hwpwm >= PCA9685_MAXCHAN)
-		reg = PCA9685_ALL_LED_OFF_L;
-	else
-		reg = LED_N_OFF_L(pwm->hwpwm);
-
-	regmap_write(pca->regmap, reg, (int)duty & 0xff);
-
-	if (pwm->hwpwm >= PCA9685_MAXCHAN)
-		reg = PCA9685_ALL_LED_OFF_H;
-	else
-		reg = LED_N_OFF_H(pwm->hwpwm);
-
-	regmap_write(pca->regmap, reg, ((int)duty >> 8) & 0xf);
-
-	/* Clear the full ON bit, otherwise the set OFF time has no effect */
-	if (pwm->hwpwm >= PCA9685_MAXCHAN)
-		reg = PCA9685_ALL_LED_ON_H;
-	else
-		reg = LED_N_ON_H(pwm->hwpwm);
-
-	regmap_write(pca->regmap, reg, 0);
-
-	return 0;
-}
-
-static int pca9685_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
-{
-	struct pca9685 *pca = to_pca(chip);
-	unsigned int reg;
-
-	/*
-	 * The PWM subsystem does not support a pre-delay.
-	 * So, set the ON-timeout to 0
-	 */
-	if (pwm->hwpwm >= PCA9685_MAXCHAN)
-		reg = PCA9685_ALL_LED_ON_L;
-	else
-		reg = LED_N_ON_L(pwm->hwpwm);
-
-	regmap_write(pca->regmap, reg, 0);
-
-	if (pwm->hwpwm >= PCA9685_MAXCHAN)
-		reg = PCA9685_ALL_LED_ON_H;
-	else
-		reg = LED_N_ON_H(pwm->hwpwm);
+	regmap_read(pca->regmap, PCA9685_PRESCALE, &val);
+	if (prescale != val) {
+		/*
+		 * Putting the chip briefly into SLEEP mode
+		 * at this point won't interfere with the
+		 * pm_runtime framework, because the pm_runtime
+		 * state is guaranteed active here.
+		 */
+		/* Put chip into sleep mode */
+		pca9685_set_sleep_mode(pca, true);
 
-	regmap_write(pca->regmap, reg, 0);
+		/* Change the chip-wide output frequency */
+		regmap_write(pca->regmap, PCA9685_PRESCALE, prescale);
 
-	/*
-	 * Clear the full-off bit.
-	 * It has precedence over the others and must be off.
-	 */
-	if (pwm->hwpwm >= PCA9685_MAXCHAN)
-		reg = PCA9685_ALL_LED_OFF_H;
-	else
-		reg = LED_N_OFF_H(pwm->hwpwm);
-
-	regmap_update_bits(pca->regmap, reg, LED_FULL, 0x0);
+		/* Wake the chip up */
+		pca9685_set_sleep_mode(pca, false);
+	}
 
+	duty = PCA9685_COUNTER_RANGE * state->duty_cycle;
+	duty = DIV_ROUND_UP_ULL(duty, state->period);
+	pca9685_pwm_set_duty(pca, pwm->hwpwm, duty);
 	return 0;
 }
 
-static void pca9685_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
-{
-	struct pca9685 *pca = to_pca(chip);
-	unsigned int reg;
-
-	if (pwm->hwpwm >= PCA9685_MAXCHAN)
-		reg = PCA9685_ALL_LED_OFF_H;
-	else
-		reg = LED_N_OFF_H(pwm->hwpwm);
-
-	regmap_write(pca->regmap, reg, LED_FULL);
-
-	/* Clear the LED_OFF counter. */
-	if (pwm->hwpwm >= PCA9685_MAXCHAN)
-		reg = PCA9685_ALL_LED_OFF_L;
-	else
-		reg = LED_N_OFF_L(pwm->hwpwm);
-
-	regmap_write(pca->regmap, reg, 0x0);
-}
-
 static int pca9685_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
 {
 	struct pca9685 *pca = to_pca(chip);
@@ -422,15 +346,13 @@ static void pca9685_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
 {
 	struct pca9685 *pca = to_pca(chip);
 
-	pca9685_pwm_disable(chip, pwm);
+	pca9685_pwm_set_duty(pca, pwm->hwpwm, 0);
 	pm_runtime_put(chip->dev);
 	pca9685_pwm_clear_inuse(pca, pwm->hwpwm);
 }
 
 static const struct pwm_ops pca9685_pwm_ops = {
-	.enable = pca9685_pwm_enable,
-	.disable = pca9685_pwm_disable,
-	.config = pca9685_pwm_config,
+	.apply = pca9685_pwm_apply,
 	.request = pca9685_pwm_request,
 	.free = pca9685_pwm_free,
 	.owner = THIS_MODULE,
@@ -461,7 +383,6 @@ static int pca9685_pwm_probe(struct i2c_client *client,
 			ret);
 		return ret;
 	}
-	pca->period_ns = PCA9685_DEFAULT_PERIOD;
 
 	i2c_set_clientdata(client, pca);
 
@@ -484,9 +405,9 @@ static int pca9685_pwm_probe(struct i2c_client *client,
 	reg &= ~(MODE1_ALLCALL | MODE1_SUB1 | MODE1_SUB2 | MODE1_SUB3);
 	regmap_write(pca->regmap, PCA9685_MODE1, reg);
 
-	/* Clear all "full off" bits */
-	regmap_write(pca->regmap, PCA9685_ALL_LED_OFF_L, 0);
-	regmap_write(pca->regmap, PCA9685_ALL_LED_OFF_H, 0);
+	/* Reset OFF registers to POR default */
+	regmap_write(pca->regmap, PCA9685_ALL_LED_OFF_L, LED_FULL);
+	regmap_write(pca->regmap, PCA9685_ALL_LED_OFF_H, LED_FULL);
 
 	pca->chip.ops = &pca9685_pwm_ops;
 	/* Add an extra channel for ALL_LED */
-- 
2.31.1

Powered by blists - more mailing lists