| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20210714151332.1.I68649745bd11a83265f1e816bf34ecc82775e95a@changeid>
Date: Wed, 14 Jul 2021 15:13:38 +0800
From: Archie Pusaka <apusaka@...gle.com>
To: linux-bluetooth <linux-bluetooth@...r.kernel.org>,
Marcel Holtmann <marcel@...tmann.org>
Cc: CrosBT Upstreaming <chromeos-bluetooth-upstreaming@...omium.org>,
Archie Pusaka <apusaka@...omium.org>,
Abhishek Pandit-Subedi <abhishekpandit@...omium.org>,
Hilda Wu <hildawu@...ltek.com>,
Johan Hedberg <johan.hedberg@...il.com>,
Luiz Augusto von Dentz <luiz.dentz@...il.com>,
linux-kernel@...r.kernel.org
Subject: [PATCH 1/3] Bluetooth: hci_h5: add WAKEUP_DISABLE flag
From: Archie Pusaka <apusaka@...omium.org>
Some RTL chips resets the FW on suspend, so wakeup is disabled on
those chips. This patch introduces this WAKEUP_DISABLE flag so that
chips that doesn't reset FW on suspend can leave the flag unset and
is allowed to wake the host.
This patch also left RTL8822 WAKEUP_DISABLE flag unset, therefore
allowing it to wake the host, and preventing reprobing on resume.
Signed-off-by: Archie Pusaka <apusaka@...omium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@...omium.org>
Reviewed-by: Hilda Wu <hildawu@...ltek.com>
---
drivers/bluetooth/hci_h5.c | 86 +++++++++++++++++++++++++++-----------
1 file changed, 62 insertions(+), 24 deletions(-)
diff --git a/drivers/bluetooth/hci_h5.c b/drivers/bluetooth/hci_h5.c
index 7b985c7cd26d..947246569434 100644
--- a/drivers/bluetooth/hci_h5.c
+++ b/drivers/bluetooth/hci_h5.c
@@ -51,8 +51,9 @@
/* H5 state flags */
enum {
- H5_RX_ESC, /* SLIP escape mode */
- H5_TX_ACK_REQ, /* Pending ack to send */
+ H5_RX_ESC, /* SLIP escape mode */
+ H5_TX_ACK_REQ, /* Pending ack to send */
+ H5_WAKEUP_DISABLE, /* Device cannot wake host */
};
struct h5 {
@@ -97,6 +98,10 @@ struct h5 {
struct gpio_desc *device_wake_gpio;
};
+enum h5_driver_info {
+ H5_INFO_WAKEUP_DISABLE = BIT(0),
+};
+
struct h5_vnd {
int (*setup)(struct h5 *h5);
void (*open)(struct h5 *h5);
@@ -106,6 +111,11 @@ struct h5_vnd {
const struct acpi_gpio_mapping *acpi_gpio_map;
};
+struct h5_device_data {
+ uint32_t driver_info;
+ struct h5_vnd *vnd;
+};
+
static void h5_reset_rx(struct h5 *h5);
static void h5_link_control(struct hci_uart *hu, const void *data, size_t len)
@@ -791,6 +801,9 @@ static int h5_serdev_probe(struct serdev_device *serdev)
{
struct device *dev = &serdev->dev;
struct h5 *h5;
+ struct hci_dev *hdev;
+ const struct h5_device_data *data;
+ int err;
h5 = devm_kzalloc(dev, sizeof(*h5), GFP_KERNEL);
if (!h5)
@@ -807,20 +820,19 @@ static int h5_serdev_probe(struct serdev_device *serdev)
if (!match)
return -ENODEV;
- h5->vnd = (const struct h5_vnd *)match->driver_data;
+ data = (const struct h5_device_data *)match->driver_data;
+ h5->vnd = data->vnd;
h5->id = (char *)match->id;
if (h5->vnd->acpi_gpio_map)
devm_acpi_dev_add_driver_gpios(dev,
h5->vnd->acpi_gpio_map);
} else {
- const void *data;
-
data = of_device_get_match_data(dev);
if (!data)
return -ENODEV;
- h5->vnd = (const struct h5_vnd *)data;
+ h5->vnd = data->vnd;
}
@@ -833,7 +845,16 @@ static int h5_serdev_probe(struct serdev_device *serdev)
if (IS_ERR(h5->device_wake_gpio))
return PTR_ERR(h5->device_wake_gpio);
- return hci_uart_register_device(&h5->serdev_hu, &h5p);
+ err = hci_uart_register_device(&h5->serdev_hu, &h5p);
+ if (err)
+ return err;
+
+ hdev = h5->serdev_hu.hdev;
+
+ if (data->driver_info & H5_INFO_WAKEUP_DISABLE)
+ set_bit(H5_WAKEUP_DISABLE, &h5->flags);
+
+ return 0;
}
static void h5_serdev_remove(struct serdev_device *serdev)
@@ -921,7 +942,8 @@ static void h5_btrtl_open(struct h5 *h5)
* done by the hci_suspend_notifier is not necessary; it actually causes
* delays and a bunch of errors to get logged, so disable it.
*/
- set_bit(HCI_UART_NO_SUSPEND_NOTIFIER, &h5->hu->flags);
+ if (test_bit(H5_WAKEUP_DISABLE, &h5->flags))
+ set_bit(HCI_UART_NO_SUSPEND_NOTIFIER, &h5->hu->flags);
/* Devices always start with these fixed parameters */
serdev_device_set_flow_control(h5->hu->serdev, false);
@@ -942,15 +964,18 @@ static void h5_btrtl_close(struct h5 *h5)
/* Suspend/resume support. On many devices the RTL BT device loses power during
* suspend/resume, causing it to lose its firmware and all state. So we simply
- * turn it off on suspend and reprobe on resume. This mirrors how RTL devices
- * are handled in the USB driver, where the USB_QUIRK_RESET_RESUME is used which
+ * turn it off on suspend and reprobe on resume. This mirrors how RTL devices
+ * are handled in the USB driver, where the BTUSB_WAKEUP_DISABLE is used which
* also causes a reprobe on resume.
*/
static int h5_btrtl_suspend(struct h5 *h5)
{
serdev_device_set_flow_control(h5->hu->serdev, false);
gpiod_set_value_cansleep(h5->device_wake_gpio, 0);
- gpiod_set_value_cansleep(h5->enable_gpio, 0);
+
+ if (test_bit(H5_WAKEUP_DISABLE, &h5->flags))
+ gpiod_set_value_cansleep(h5->enable_gpio, 0);
+
return 0;
}
@@ -976,17 +1001,21 @@ static void h5_btrtl_reprobe_worker(struct work_struct *work)
static int h5_btrtl_resume(struct h5 *h5)
{
- struct h5_btrtl_reprobe *reprobe;
+ if (test_bit(H5_WAKEUP_DISABLE, &h5->flags)) {
+ struct h5_btrtl_reprobe *reprobe;
- reprobe = kzalloc(sizeof(*reprobe), GFP_KERNEL);
- if (!reprobe)
- return -ENOMEM;
+ reprobe = kzalloc(sizeof(*reprobe), GFP_KERNEL);
+ if (!reprobe)
+ return -ENOMEM;
- __module_get(THIS_MODULE);
+ __module_get(THIS_MODULE);
- INIT_WORK(&reprobe->work, h5_btrtl_reprobe_worker);
- reprobe->dev = get_device(&h5->hu->serdev->dev);
- queue_work(system_long_wq, &reprobe->work);
+ INIT_WORK(&reprobe->work, h5_btrtl_reprobe_worker);
+ reprobe->dev = get_device(&h5->hu->serdev->dev);
+ queue_work(system_long_wq, &reprobe->work);
+ } else {
+ gpiod_set_value_cansleep(h5->device_wake_gpio, 1);
+ }
return 0;
}
@@ -1008,13 +1037,22 @@ static struct h5_vnd rtl_vnd = {
.resume = h5_btrtl_resume,
.acpi_gpio_map = acpi_btrtl_gpios,
};
+
+static const struct h5_device_data h5_data_rtl8822cs = {
+ .vnd = &rtl_vnd,
+};
+
+static const struct h5_device_data h5_data_rtl8723bs = {
+ .driver_info = H5_INFO_WAKEUP_DISABLE,
+ .vnd = &rtl_vnd,
+};
#endif
#ifdef CONFIG_ACPI
static const struct acpi_device_id h5_acpi_match[] = {
#ifdef CONFIG_BT_HCIUART_RTL
- { "OBDA0623", (kernel_ulong_t)&rtl_vnd },
- { "OBDA8723", (kernel_ulong_t)&rtl_vnd },
+ { "OBDA0623", (kernel_ulong_t)&h5_data_rtl8723bs },
+ { "OBDA8723", (kernel_ulong_t)&h5_data_rtl8723bs },
#endif
{ },
};
@@ -1028,11 +1066,11 @@ static const struct dev_pm_ops h5_serdev_pm_ops = {
static const struct of_device_id rtl_bluetooth_of_match[] = {
#ifdef CONFIG_BT_HCIUART_RTL
{ .compatible = "realtek,rtl8822cs-bt",
- .data = (const void *)&rtl_vnd },
+ .data = (const void *)&h5_data_rtl8822cs },
{ .compatible = "realtek,rtl8723bs-bt",
- .data = (const void *)&rtl_vnd },
+ .data = (const void *)&h5_data_rtl8723bs },
{ .compatible = "realtek,rtl8723ds-bt",
- .data = (const void *)&rtl_vnd },
+ .data = (const void *)&h5_data_rtl8723bs },
#endif
{ },
};
--
2.32.0.93.g670b81a890-goog
Powered by blists - more mailing lists