| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <YVTfDJNW5Pe3iAR/@robh.at.kernel.org>
Date: Wed, 29 Sep 2021 16:47:56 -0500
From: Rob Herring <robh@...nel.org>
To: Zhiyong Tao <zhiyong.tao@...iatek.com>
Cc: linus.walleij@...aro.org, mark.rutland@....com,
matthias.bgg@...il.com, sean.wang@...nel.org,
srv_heupstream@...iatek.com, hui.liu@...iatek.com,
light.hsieh@...iatek.com, biao.huang@...iatek.com,
hongzhou.yang@...iatek.com, sean.wang@...iatek.com,
seiya.wang@...iatek.com, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-mediatek@...ts.infradead.org, linux-gpio@...r.kernel.org
Subject: Re: [PATCH v14 2/5] dt-bindings: pinctrl: mt8195: change pull
up/down description
On Fri, Sep 24, 2021 at 04:06:29PM +0800, Zhiyong Tao wrote:
> For supporting SI units in "bias-pull-down" & "bias-pull-up",
> change pull up/down description
> and add "mediatek,rsel_resistance_in_si_unit" description.
>
> Signed-off-by: Zhiyong Tao <zhiyong.tao@...iatek.com>
> ---
> .../bindings/pinctrl/pinctrl-mt8195.yaml | 86 ++++++++++++++++++-
> 1 file changed, 84 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> index 2f12ec59eee5..5f642bef72af 100644
> --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml
> @@ -49,6 +49,12 @@ properties:
> description: The interrupt outputs to sysirq.
> maxItems: 1
>
> + mediatek,rsel_resistance_in_si_unit:
s/_/-/
> + type: boolean
> + description: |
> + Identifying i2c pins pull up/down type which is RSEL. It can support
> + RSEL define or si unit value(ohm) to set different resistance.
Aren't the RSEL and ohms disjoint values? 0-207 for RSEL and >1000 for
ohms. Why is this property even needed.
> +
> #PIN CONFIGURATION NODES
> patternProperties:
> '-pins$':
> @@ -85,9 +91,85 @@ patternProperties:
> 2/4/6/8/10/12/14/16mA in mt8195.
> enum: [0, 1, 2, 3, 4, 5, 6, 7]
>
> - bias-pull-down: true
> + bias-pull-down:
> + description: |
> + For pull down type is normal, it don't need add RSEL & R1R0 define
> + and resistance value.
> + For pull down type is PUPD/R0/R1 type, it can add R1R0 define to
> + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
> + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11"
> + define in mt8195.
> + For pull down type is RSEL, it can add RSEL define & resistance value(ohm)
> + to set different resistance by identifying property "mediatek,rsel_resistance_in_si_unit".
> + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
> + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100"
> + & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
> + define in mt8195. It can also support resistance value(ohm) "75000" & "5000" in mt8195.
> + oneOf:
Because of the indentation, this is all just part of 'description'.
> + - enum: [100, 101, 102, 103]
> + - description: mt8195 pull down PUPD/R0/R1 type define value.
This entry is always true.
> + - enum: [200, 201, 202, 203, 204, 205, 206, 207]
Are these supposed to be hex?
> + - description: mt8195 pull down RSEL type define value.
And so is this one. That makes 'oneOf' always false.
> + - enum: [75000, 5000]
> + - description: mt8195 pull down RSEL type si unit value(ohm).
> +
> + An example of using RSEL define:
> + pincontroller {
> + i2c0_pin {
> + pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> + bias-pull-down = <MTK_PULL_SET_RSEL_001>;
> + };
> + };
> + An example of using si unit resistance value(ohm):
> + &pio {
> + mediatek,rsel_resistance_in_si_unit;
> + }
> + pincontroller {
> + i2c0_pin {
> + pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> + bias-pull-down = <75000>;
> + };
> + };
>
> - bias-pull-up: true
> + bias-pull-up:
> + description: |
> + For pull up type is normal, it don't need add RSEL & R1R0 define
> + and resistance value.
> + For pull up type is PUPD/R0/R1 type, it can add R1R0 define to
> + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
> + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11"
> + define in mt8195.
> + For pull up type is RSEL, it can add RSEL define & resistance value(ohm)
> + to set different resistance by identifying property "mediatek,rsel_resistance_in_si_unit".
> + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
> + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100"
> + & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
> + define in mt8195. It can also support resistance value(ohm)
> + "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & "75000" in mt8195.
> + oneOf:
> + - enum: [100, 101, 102, 103]
> + - description: mt8195 pull up PUPD/R0/R1 type define value.
> + - enum: [200, 201, 202, 203, 204, 205, 206, 207]
> + - description: mt8195 pull up RSEL type define value.
> + - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000]
> + - description: mt8195 pull up RSEL type si unit value(ohm).
Same issues here.
> + An example of using RSEL define:
> + pincontroller {
> + i2c0_pin {
> + pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> + bias-pull-up = <MTK_PULL_SET_RSEL_001>;
> + };
> + };
> + An example of using si unit resistance value(ohm):
> + &pio {
> + mediatek,rsel_resistance_in_si_unit;
> + }
> + pincontroller {
> + i2c0_pin {
> + pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
> + bias-pull-up = <1000>;
> + };
> + };
>
> bias-disable: true
>
> --
> 2.25.1
>
>
Powered by blists - more mailing lists