[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <1jfsr659v1.fsf@starbuckisacylon.baylibre.com>
Date: Mon, 06 Dec 2021 10:54:19 +0100
From: Jerome Brunet <jbrunet@...libre.com>
To: Martin Blumenstingl <martin.blumenstingl@...glemail.com>,
linux-amlogic@...ts.infradead.org, alsa-devel@...a-project.org
Cc: linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
Christian Hewitt <christianshewitt@...il.com>,
Geraldo Nascimento <geraldogabriel@...il.com>
Subject: Re: [PATCH RFC v1 2/2] ASoC: meson: aiu: Move AIU_I2S_MISC hold
setting to aiu-fifo-i2s
On Sun 05 Dec 2021 at 19:08, Martin Blumenstingl <martin.blumenstingl@...glemail.com> wrote:
> The out-of-tree vendor driver uses the following approach to set the
> AIU_I2S_MISC register:
> 1) write AIU_MEM_I2S_START_PTR and AIU_MEM_I2S_RD_PTR
> 2) configure AIU_I2S_MUTE_SWAP[15:0]
> 3) write AIU_MEM_I2S_END_PTR
> 4) set AIU_I2S_MISC[2] to 1 (documented as: "put I2S interface in hold
> mode")
> 5) set AIU_I2S_MISC[4] to 1 (depending on the driver revision it always
> stays at 1 while for older drivers this bit is unset in step 4)
> 6) set AIU_I2S_MISC[2] to 0
> 7) write AIU_MEM_I2S_MASKS
> 8) toggle AIU_MEM_I2S_CONTROL[0]
> 9) toggle AIU_MEM_I2S_BUF_CNTL[0]
>
> Additional testing shows that when AIU_I2S_MISC[2] is set to 1 then no
> interrupts are generated anymore. The way this bit is managed by the
> vendor driver as well as not getting any interrupts can mean that it's
> related to the FIFO and not the encoder.
Not necessarily. If the encoder stops pulling data, the FIFO will going
over the DDR. Since it generates an IRQ after reading N bytes, IRQ would
stop too. AFAIK, if the pipeline is stalled, the IRQ stops anyway
... but this is not really important
>
> Move setting the AIU_I2S_MISC[2] bit to aiu_fifo_i2s_hw_params() so it
> closer resembles the flow in the vendor kernel. While here also
> configure AIU_I2S_MISC[4] (documented as: "force each audio data to
> left or right according to the bit attached with the audio data")
> similar to how the vendor driver does this.
I understand the part of HOLD, not about FORCE_LR.
Is it necessary to fix the problem ? Have you tested without this change
?
> This fixes the infamous and
> long-standing "machine gun noise" issue (a buffer underrun issue).
Well done ! It took us a while to nail it, Thanks a lot !!
>
> Fixes: 6ae9ca9ce986bf ("ASoC: meson: aiu: add i2s and spdif support")
> Reported-by: Christian Hewitt <christianshewitt@...il.com>
> Reported-by: Geraldo Nascimento <geraldogabriel@...il.com>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@...glemail.com>
> ---
> sound/soc/meson/aiu-encoder-i2s.c | 33 -------------------------------
> sound/soc/meson/aiu-fifo-i2s.c | 12 +++++++++++
> 2 files changed, 12 insertions(+), 33 deletions(-)
>
> diff --git a/sound/soc/meson/aiu-encoder-i2s.c b/sound/soc/meson/aiu-encoder-i2s.c
> index 932224552146..67729de41a73 100644
> --- a/sound/soc/meson/aiu-encoder-i2s.c
> +++ b/sound/soc/meson/aiu-encoder-i2s.c
> @@ -18,7 +18,6 @@
> #define AIU_RST_SOFT_I2S_FAST BIT(0)
>
> #define AIU_I2S_DAC_CFG_MSB_FIRST BIT(2)
> -#define AIU_I2S_MISC_HOLD_EN BIT(2)
> #define AIU_CLK_CTRL_I2S_DIV_EN BIT(0)
> #define AIU_CLK_CTRL_I2S_DIV GENMASK(3, 2)
> #define AIU_CLK_CTRL_AOCLK_INVERT BIT(6)
> @@ -36,37 +35,6 @@ static void aiu_encoder_i2s_divider_enable(struct snd_soc_component *component,
> enable ? AIU_CLK_CTRL_I2S_DIV_EN : 0);
> }
>
> -static void aiu_encoder_i2s_hold(struct snd_soc_component *component,
> - bool enable)
> -{
> - snd_soc_component_update_bits(component, AIU_I2S_MISC,
> - AIU_I2S_MISC_HOLD_EN,
> - enable ? AIU_I2S_MISC_HOLD_EN : 0);
> -}
> -
> -static int aiu_encoder_i2s_trigger(struct snd_pcm_substream *substream, int cmd,
> - struct snd_soc_dai *dai)
> -{
> - struct snd_soc_component *component = dai->component;
> -
> - switch (cmd) {
> - case SNDRV_PCM_TRIGGER_START:
> - case SNDRV_PCM_TRIGGER_RESUME:
> - case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
> - aiu_encoder_i2s_hold(component, false);
> - return 0;
> -
> - case SNDRV_PCM_TRIGGER_STOP:
> - case SNDRV_PCM_TRIGGER_SUSPEND:
> - case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
> - aiu_encoder_i2s_hold(component, true);
> - return 0;
> -
> - default:
> - return -EINVAL;
> - }
> -}
> -
> static int aiu_encoder_i2s_setup_desc(struct snd_soc_component *component,
> struct snd_pcm_hw_params *params)
> {
> @@ -353,7 +321,6 @@ static void aiu_encoder_i2s_shutdown(struct snd_pcm_substream *substream,
> }
>
> const struct snd_soc_dai_ops aiu_encoder_i2s_dai_ops = {
> - .trigger = aiu_encoder_i2s_trigger,
> .hw_params = aiu_encoder_i2s_hw_params,
> .hw_free = aiu_encoder_i2s_hw_free,
> .set_fmt = aiu_encoder_i2s_set_fmt,
> diff --git a/sound/soc/meson/aiu-fifo-i2s.c b/sound/soc/meson/aiu-fifo-i2s.c
> index 2388a2d0b3a6..d0a1090d6465 100644
> --- a/sound/soc/meson/aiu-fifo-i2s.c
> +++ b/sound/soc/meson/aiu-fifo-i2s.c
> @@ -20,6 +20,8 @@
> #define AIU_MEM_I2S_CONTROL_MODE_16BIT BIT(6)
> #define AIU_MEM_I2S_BUF_CNTL_INIT BIT(0)
> #define AIU_RST_SOFT_I2S_FAST BIT(0)
> +#define AIU_I2S_MISC_HOLD_EN BIT(2)
> +#define AIU_I2S_MISC_FORCE_LEFT_RIGHT BIT(4)
>
> #define AIU_FIFO_I2S_BLOCK 256
>
> @@ -90,6 +92,10 @@ static int aiu_fifo_i2s_hw_params(struct snd_pcm_substream *substream,
> unsigned int val;
> int ret;
>
> + snd_soc_component_update_bits(component, AIU_I2S_MISC,
> + AIU_I2S_MISC_HOLD_EN,
> + AIU_I2S_MISC_HOLD_EN);
> +
> ret = aiu_fifo_hw_params(substream, params, dai);
> if (ret)
> return ret;
> @@ -117,6 +123,12 @@ static int aiu_fifo_i2s_hw_params(struct snd_pcm_substream *substream,
> snd_soc_component_update_bits(component, AIU_MEM_I2S_MASKS,
> AIU_MEM_I2S_MASKS_IRQ_BLOCK, val);
>
> + snd_soc_component_update_bits(component, AIU_I2S_MISC,
> + AIU_I2S_MISC_FORCE_LEFT_RIGHT,
> + AIU_I2S_MISC_FORCE_LEFT_RIGHT);
If it is necessary, even if we don't really understand why, it is fine
by me. But if it is not, I would prefer we leave it out of it, or at
least, make it a separate patch.
> + snd_soc_component_update_bits(component, AIU_I2S_MISC,
> + AIU_I2S_MISC_HOLD_EN, 0);
> +
> return 0;
> }
Powered by blists - more mailing lists