linux-kernel - [RFC PATCH 2/4] mtd: rawnand: gpmi: support fast edo timings for mx28

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20211217155512.1877408-3-dario.binacchi@amarulasolutions.com>
Date:   Fri, 17 Dec 2021 16:55:10 +0100
From:   Dario Binacchi <dario.binacchi@...rulasolutions.com>
To:     linux-kernel@...r.kernel.org
Cc:     Dario Binacchi <dario.binacchi@...rulasolutions.com>,
        Michael Trimarchi <michael@...rulasolutions.com>,
        Han Xu <han.xu@....com>,
        Miquel Raynal <miquel.raynal@...tlin.com>,
        Richard Weinberger <richard@....at>,
        Vignesh Raghavendra <vigneshr@...com>,
        linux-mtd@...ts.infradead.org
Subject: [RFC PATCH 2/4] mtd: rawnand: gpmi: support fast edo timings for mx28

In the mx28 reference manual there are examples of how to set up the
GPMI controller to support fast NAND EDO timing.

This patch has been tested on a 2048/64 byte NAND (Micron MT29F2G08ABAEAH4).
Kernel mtd tests:
 - mtd_nandbiterrs
 - mtd_nandecctest
 - mtd_oobtest
 - mtd_pagetest
 - mtd_readtest
 - mtd_speedtest
 - mtd_stresstest
 - mtd_subpagetest
 - mtd_torturetest [cycles_count = 10000000]
run without errors.

Before this patch (mode 0):
---------------------------
eraseblock write speed is 2098 KiB/s
eraseblock read speed is 2680 KiB/s
page write speed is 1689 KiB/s
page read speed is 2522 KiB/s
2 page write speed is 1899 KiB/s
2 page read speed is 2579 KiB/s
erase speed is 128000 KiB/s
2x multi-block erase speed is 73142 KiB/s
4x multi-block erase speed is 204800 KiB/s
8x multi-block erase speed is 256000 KiB/s
16x multi-block erase speed is 256000 KiB/s
32x multi-block erase speed is 256000 KiB/s
64x multi-block erase speed is 256000 KiB/s

After this patch (mode 5):
-------------------------
eraseblock write speed is 3390 KiB/s
eraseblock read speed is 5688 KiB/s
page write speed is 2680 KiB/s
page read speed is 4876 KiB/s
2 page write speed is 2909 KiB/s
2 page read speed is 5224 KiB/s
erase speed is 170666 KiB/s
2x multi-block erase speed is 204800 KiB/s
4x multi-block erase speed is 256000 KiB/s
8x multi-block erase speed is 256000 KiB/s
16x multi-block erase speed is 256000 KiB/s
32x multi-block erase speed is 256000 KiB/s
64x multi-block erase speed is 256000 KiB/s

Signed-off-by: Dario Binacchi <dario.binacchi@...rulasolutions.com>
Co-developed-by: Michael Trimarchi <michael@...rulasolutions.com>
---

 drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
index 65bcd1c548d2..fd935e893daf 100644
--- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
@@ -772,8 +772,8 @@ static int gpmi_setup_interface(struct nand_chip *chip, int chipnr,
 	if (IS_ERR(sdr))
 		return PTR_ERR(sdr);
 
-	/* Only MX6 GPMI controller can reach EDO timings */
-	if (sdr->tRC_min <= 25000 && !GPMI_IS_MX6(this))
+	/* Only MX28/MX6 GPMI controller can reach EDO timings */
+	if (sdr->tRC_min <= 25000 && !GPMI_IS_MX28(this) && !GPMI_IS_MX6(this))
 		return -ENOTSUPP;
 
 	/* Stop here if this call was just a check */
-- 
2.32.0