[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <20220224235403.GA303878@bhelgaas>
Date: Thu, 24 Feb 2022 17:54:03 -0600
From: Bjorn Helgaas <helgaas@...nel.org>
To: Hongxing Zhu <hongxing.zhu@....com>
Cc: "l.stach@...gutronix.de" <l.stach@...gutronix.de>,
"bhelgaas@...gle.com" <bhelgaas@...gle.com>,
"broonie@...nel.org" <broonie@...nel.org>,
"lorenzo.pieralisi@....com" <lorenzo.pieralisi@....com>,
"jingoohan1@...il.com" <jingoohan1@...il.com>,
"festevam@...il.com" <festevam@...il.com>,
"francesco.dolcini@...adex.com" <francesco.dolcini@...adex.com>,
"linux-pci@...r.kernel.org" <linux-pci@...r.kernel.org>,
"linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"kernel@...gutronix.de" <kernel@...gutronix.de>,
dl-linux-imx <linux-imx@....com>
Subject: Re: [PATCH v7 8/8] PCI: imx6: Add the compliance tests mode support
On Thu, Feb 24, 2022 at 07:50:09AM +0000, Hongxing Zhu wrote:
> > -----Original Message-----
> > From: Bjorn Helgaas <helgaas@...nel.org>
> > Sent: 2022年2月24日 1:40
> > To: Hongxing Zhu <hongxing.zhu@....com>
> > Cc: l.stach@...gutronix.de; bhelgaas@...gle.com; broonie@...nel.org;
> > lorenzo.pieralisi@....com; jingoohan1@...il.com; festevam@...il.com;
> > francesco.dolcini@...adex.com; linux-pci@...r.kernel.org;
> > linux-arm-kernel@...ts.infradead.org; linux-kernel@...r.kernel.org;
> > kernel@...gutronix.de; dl-linux-imx <linux-imx@....com>
> > Subject: Re: [PATCH v7 8/8] PCI: imx6: Add the compliance tests mode support
> > Is this a reference to a spec? If so, I can't tell the name of the spec, the
> > revision, or the section number.
> Yes, it is a reference to a spec. How about change them to the following?
>
> PCI: imx6: Add compliance tests mode support
>
> Refer to the Chapter 3.2 System Board Signal Quality of PCI Express
> Architecture PHY Test Specification Revision 2.0.
>
> Signal quality tests (for example: jitter, differential eye opening and
> so on) can be executed with devices in the polling.compliance state.
>
> To let the device support polling.compliance state, the clocks and powers
> shouldn't be turned off when the probe of device driver fails.
>
> Based on CLB (Compliance Load Board) Test Fixture and so on test
> equipments, the PHY link would be down during the compliance tests.
> Refer to this scenario, add the i.MX PCIe compliance tests mode enable
> support, and keep the clocks and powers on, and finish the driver probe
> without error return.
>
> Use the "pci_imx6.compliance=1" in kernel command line to enable the
> compliance tests mode.
Sounds good, thanks.
Powered by blists - more mailing lists