linux-kernel - Re: [PATCH 11/11] arm64: dts: Add Pensando Elba SoC support

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <eed2f337-3d5a-3440-d19e-c5ff032409ab@linaro.org>
Date:   Thu, 7 Apr 2022 21:06:20 +0200
From:   Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
To:     Brad Larson <brad@...sando.io>,
        linux-arm-kernel@...ts.infradead.org
Cc:     arnd@...db.de, linus.walleij@...aro.org, bgolaszewski@...libre.com,
        broonie@...nel.org, fancer.lancer@...il.com,
        adrian.hunter@...el.com, ulf.hansson@...aro.org, olof@...om.net,
        dac2@...sando.io, linux-gpio@...r.kernel.org,
        linux-spi@...r.kernel.org, linux-mmc@...r.kernel.org,
        devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH 11/11] arm64: dts: Add Pensando Elba SoC support

On 07/04/2022 01:36, Brad Larson wrote:
> Add Pensando common and Elba SoC specific device nodes
> 
> Signed-off-by: Brad Larson <brad@...sando.io>
> ---
> Change from V3:
> - Changed to dual copyright (GPL-2.0+ OR MIT)
> - Minor changes from review input

Thank you for your patch. There is something to discuss/improve.

(...)

> +&i2c0 {
> +	clock-frequency = <100000>;
> +	status = "okay";
> +	rtc@51 {
> +		compatible = "nxp,pcf85263";
> +		reg = <0x51>;
> +	};
> +};
> +
> +&spi0 {
> +	num-cs = <4>;
> +	cs-gpios = <0>, <0>, <&porta 1 GPIO_ACTIVE_LOW>,
> +		   <&porta 7 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +	spi0_cs0@0 {

Generic node name needed matching the class of a devicxe.

> +		compatible = "semtech,sx1301";	/* Enable spidev */

This comment is a bit odd... did you just use random compatible from
spidev instead of defining proper compatible?


> +		#address-cells = <1>;
> +		#size-cells = <1>;

Why address/size cells?

> +		spi-max-frequency = <12000000>;
> +		reg = <0>;

Please put reg just after compatible. It's the most common pattern.

> +	};
> +
> +	spi0_cs1@1 {
> +		compatible = "semtech,sx1301";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		spi-max-frequency = <12000000>;
> +		reg = <1>;
> +	};
> +

(...)

> +
> +		emmc: mmc@...40000 {
> +			compatible = "pensando,elba-sd4hc", "cdns,sd4hc";
> +			clocks = <&emmc_clk>;
> +			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
> +			reg = <0x0 0x30440000 0x0 0x10000>,
> +			      <0x0 0x30480044 0x0 0x4>;	/* byte-lane ctrl */
> +			cdns,phy-input-delay-sd-highspeed = <0x4>;
> +			cdns,phy-input-delay-legacy = <0x4>;
> +			cdns,phy-input-delay-sd-uhs-sdr50 = <0x6>;
> +			cdns,phy-input-delay-sd-uhs-ddr50 = <0x16>;
> +			mmc-ddr-1_8v;
> +			status = "disabled";
> +		};
> +
> +		mssoc: mssoc@...c0000 {

Generic node name.

> +			compatible = "syscon", "simple-mfd";

This does not look correct. Syscon is okay, but why do you need
simple-mfd (there are no children here)?

> +			reg = <0x0 0x307c0000 0x0 0x3000>;
> +		};
> +	};
> +};


Best regards,
Krzysztof