Message-ID: <e690ccba-50ef-da1f-14a1-e4a6b284ba3c@kernel.org>
Date:   Thu, 7 Apr 2022 11:54:09 +0300
From:   Roger Quadros <rogerq@...nel.org>
To:     Aswath Govindraju <a-govindraju@...com>
Cc:     Vignesh Raghavendra <vigneshr@...com>,
        Kishon Vijay Abraham I <kishon@...com>,
        Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzk+dt@...nel.org>,
        Felipe Balbi <balbi@...nel.org>, linux-usb@...r.kernel.org,
        devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v3 2/2] drivers: usb: dwc3: Add AM62 USB wrapper driver



On 07/04/2022 11:27, Aswath Govindraju wrote:
> Hi Roger,
> 
> On 07/04/22 13:54, Aswath Govindraju wrote:
>> Hi Roger,
>>
>> On 07/04/22 13:50, Roger Quadros wrote:
>>> Hi Aswath,
>>>
>>> On 06/04/2022 16:52, Aswath Govindraju wrote:
>>>> In AM62 SoC, the Designware Core USB3 IP is progammed to operate in USB2.0
>>>> only mode. Add driver for AM62 USB DWC3 Wrapper.
>>>>
>>>> Signed-off-by: Aswath Govindraju <a-govindraju@...com>
>>>> ---
>>>>
>>>> changes since v2:
>>>> - Removed the implementation of detecting the role from the wrapper
>>>>   driver and moved the implementation to using linux,extcon-usb-gpio
>>>>   driver for role detection.
>>>
>>> I'm a bit puzzled. So ID is managed by extcon-usb-gpio driver and
>>> VBUS is managed by this driver.
>>>
>>> So who decides the USB ports state based on the below truth table?
>>>
>>> +	/*
>>> +	 * ID | VBUS | STATE
>>> +	 * -----------------
>>> +	 * 0  | 0    | HOST
>>> +	 * 0  | 1    | HOST
>>> +	 * 1  | 0    | Disconnected (set mode valid to 0)
>>> +	 * 1  | 1    | Device
>>> +	 *
>>> +	 */
>>>
>>> If only ID signal is available to extcon-usb-gpio driver it cannot detect
>>> the Disconnected state. We need to set mode valid to 0 for disconnected state.
>>>
>>
>> Yes that is correct, the mode valid signal needs to be set when there is
>> no cable connected. I am slightly confused on why 0-0 state is not
>> considered disconnected? So, whenever VBUS is not high it should be
>> disconnected right?

Not necessarily. We might be in host mode (ID=0) and just not turned on the VBUS regulator (VBUS=0).
Is this to be treated as disconnected?

I'm just pointing out that things won't function anymore like the below code you had earlier
as you have decoupled id_state from vbus_state.

+	/* detemine the role or find out if disconnect event */
+	if (id_state) {
+		detect_role = DEVICE;
+		if (vbus_state)
+			connect = 1;
+	} else {
+		detect_role = HOST;
+		connect = 1;
+	}

Now you are setting connect independently of ID. i.e. connect = vbus_state.

Is that what you want?

cheers,
-roger

>>
> 
> Sorry, pressed the send button without reading everything properly.
> 
> The implementation is such that the extcon-usb-gpio only updates the
> role to the core driver based on ID pin state and the Mode valid bit is
> set by the wrapper based on the VBUS state.
> 
> Thanks,
> Aswath
> 
>> Thanks,
>> Aswath
>>
>>> cheers,
>>> -roger
>>>
>>>
>>>> - Updated the binding documentation and example to reflect the same.
>>>>
>>>>
>>>>  drivers/usb/dwc3/Kconfig     |   9 +
>>>>  drivers/usb/dwc3/Makefile    |   1 +
>>>>  drivers/usb/dwc3/dwc3-am62.c | 446 +++++++++++++++++++++++++++++++++++
>>>>  3 files changed, 456 insertions(+)
>>>>  create mode 100644 drivers/usb/dwc3/dwc3-am62.c
>>>>
>>>> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
>>>> index c483f28b695d..cd9a734522a7 100644
>>>> --- a/drivers/usb/dwc3/Kconfig
>>>> +++ b/drivers/usb/dwc3/Kconfig
>>>> @@ -159,4 +159,13 @@ config USB_DWC3_XILINX
>>>>  	  This driver handles both ZynqMP and Versal SoC operations.
>>>>  	  Say 'Y' or 'M' if you have one such device.
>>>>  
>>>> +config USB_DWC3_AM62
>>>> +	tristate "Texas Instruments AM62 Platforms"
>>>> +	depends on ARCH_K3 || COMPILE_TEST
>>>> +	default USB_DWC3
>>>> +	help
>>>> +	  Support TI's AM62 platforms with DesignWare Core USB3 IP.
>>>> +	  The Designware Core USB3 IP is progammed to operate in
>>>> +	  in USB 2.0 mode only.
>>>> +	  Say 'Y' or 'M' here if you have one such device
>>>>  endif
>>>> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
>>>> index 2d499de6f66a..9f66bd82b639 100644
>>>> --- a/drivers/usb/dwc3/Makefile
>>>> +++ b/drivers/usb/dwc3/Makefile
>>>> @@ -42,6 +42,7 @@ endif
>>>>  # and allyesconfig builds.
>>>>  ##
>>>>  
>>>> +obj-$(CONFIG_USB_DWC3_AM62)		+= dwc3-am62.o
>>>>  obj-$(CONFIG_USB_DWC3_OMAP)		+= dwc3-omap.o
>>>>  obj-$(CONFIG_USB_DWC3_EXYNOS)		+= dwc3-exynos.o
>>>>  obj-$(CONFIG_USB_DWC3_PCI)		+= dwc3-pci.o
>>>> diff --git a/drivers/usb/dwc3/dwc3-am62.c b/drivers/usb/dwc3/dwc3-am62.c
>>>> new file mode 100644
>>>> index 000000000000..5700258c8deb
>>>> --- /dev/null
>>>> +++ b/drivers/usb/dwc3/dwc3-am62.c
>>>> @@ -0,0 +1,446 @@
>>>> +// SPDX-License-Identifier: GPL-2.0
>>>> +/*
>>>> + * dwc3-am62.c - TI specific Glue layer for AM62 DWC3 USB Controller
>>>> + *
>>>> + * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com
>>>> + */
>>>> +
>>>> +#include <linux/init.h>
>>>> +#include <linux/interrupt.h>
>>>> +#include <linux/irq.h>
>>>> +#include <linux/kernel.h>
>>>> +#include <linux/module.h>
>>>> +#include <linux/platform_device.h>
>>>> +#include <linux/workqueue.h>
>>>> +#include <linux/mfd/syscon.h>
>>>> +#include <linux/of.h>
>>>> +#include <linux/of_device.h>
>>>> +#include <linux/pm_runtime.h>
>>>> +#include <linux/clk.h>
>>>> +#include <linux/regmap.h>
>>>> +#include <linux/devm-helpers.h>
>>>> +#include <linux/pinctrl/consumer.h>
>>>> +
>>>> +/* USB WRAPPER register offsets */
>>>> +#define USBSS_PID			0x0
>>>> +#define USBSS_OVERCURRENT_CTRL		0x4
>>>> +#define USBSS_PHY_CONFIG		0x8
>>>> +#define USBSS_PHY_TEST			0xc
>>>> +#define USBSS_CORE_STAT			0x14
>>>> +#define USBSS_HOST_VBUS_CTRL		0x18
>>>> +#define USBSS_MODE_CONTROL		0x1c
>>>> +#define USBSS_WAKEUP_CONFIG		0x30
>>>> +#define USBSS_WAKEUP_STAT		0x34
>>>> +#define USBSS_OVERRIDE_CONFIG		0x38
>>>> +#define USBSS_IRQ_MISC_STATUS_RAW	0x430
>>>> +#define USBSS_IRQ_MISC_STATUS		0x434
>>>> +#define USBSS_IRQ_MISC_ENABLE_SET	0x438
>>>> +#define USBSS_IRQ_MISC_ENABLE_CLR	0x43c
>>>> +#define USBSS_IRQ_MISC_EOI		0x440
>>>> +#define USBSS_INTR_TEST			0x490
>>>> +#define USBSS_VBUS_FILTER		0x614
>>>> +#define USBSS_VBUS_STAT			0x618
>>>> +#define USBSS_DEBUG_CFG			0x708
>>>> +#define USBSS_DEBUG_DATA		0x70c
>>>> +#define USBSS_HOST_HUB_CTRL		0x714
>>>> +
>>>> +/* PHY CONFIG register bits */
>>>> +#define USBSS_PHY_VBUS_SEL_MASK		GENMASK(2, 1)
>>>> +#define USBSS_PHY_VBUS_SEL_SHIFT	1
>>>> +#define USBSS_PHY_LANE_REVERSE		BIT(0)
>>>> +
>>>> +/* MODE CONTROL register bits */
>>>> +#define USBSS_MODE_VALID	BIT(0)
>>>> +
>>>> +/* WAKEUP CONFIG register bits */
>>>> +#define USBSS_WAKEUP_CFG_OVERCURRENT_EN	BIT(3)
>>>> +#define USBSS_WAKEUP_CFG_LINESTATE_EN	BIT(2)
>>>> +#define USBSS_WAKEUP_CFG_SESSVALID_EN	BIT(1)
>>>> +#define USBSS_WAKEUP_CFG_VBUSVALID_EN	BIT(0)
>>>> +
>>>> +/* WAKEUP STAT register bits */
>>>> +#define USBSS_WAKEUP_STAT_OVERCURRENT	BIT(4)
>>>> +#define USBSS_WAKEUP_STAT_LINESTATE	BIT(3)
>>>> +#define USBSS_WAKEUP_STAT_SESSVALID	BIT(2)
>>>> +#define USBSS_WAKEUP_STAT_VBUSVALID	BIT(1)
>>>> +#define USBSS_WAKEUP_STAT_CLR		BIT(0)
>>>> +
>>>> +/* IRQ_MISC_STATUS_RAW register bits */
>>>> +#define USBSS_IRQ_MISC_RAW_VBUSVALID	BIT(22)
>>>> +#define USBSS_IRQ_MISC_RAW_SESSVALID	BIT(20)
>>>> +
>>>> +/* IRQ_MISC_STATUS register bits */
>>>> +#define USBSS_IRQ_MISC_VBUSVALID	BIT(22)
>>>> +#define USBSS_IRQ_MISC_SESSVALID	BIT(20)
>>>> +
>>>> +/* IRQ_MISC_ENABLE_SET register bits */
>>>> +#define USBSS_IRQ_MISC_ENABLE_SET_VBUSVALID	BIT(22)
>>>> +#define USBSS_IRQ_MISC_ENABLE_SET_SESSVALID	BIT(20)
>>>> +
>>>> +/* IRQ_MISC_ENABLE_CLR register bits */
>>>> +#define USBSS_IRQ_MISC_ENABLE_CLR_VBUSVALID	BIT(22)
>>>> +#define USBSS_IRQ_MISC_ENABLE_CLR_SESSVALID	BIT(20)
>>>> +
>>>> +/* IRQ_MISC_EOI register bits */
>>>> +#define USBSS_IRQ_MISC_EOI_VECTOR	BIT(0)
>>>> +
>>>> +/* VBUS_STAT register bits */
>>>> +#define USBSS_VBUS_STAT_SESSVALID	BIT(2)
>>>> +#define USBSS_VBUS_STAT_VBUSVALID	BIT(0)
>>>> +
>>>> +/* Mask for PHY PLL REFCLK */
>>>> +#define PHY_PLL_REFCLK_MASK	GENMASK(3, 0)
>>>> +
>>>> +#define DWC3_AM62_AUTOSUSPEND_DELAY	100
>>>> +
>>>> +struct dwc3_data {
>>>> +	struct device *dev;
>>>> +	void __iomem *usbss;
>>>> +	struct clk *usb2_refclk;
>>>> +	struct work_struct work;
>>>> +	int vbus_irq;
>>>> +	int rate_code;
>>>> +	int connect;
>>>> +	struct regmap *syscon;
>>>> +	unsigned int offset;
>>>> +	unsigned int vbus_divider;
>>>> +};
>>>> +
>>>> +static const int dwc3_ti_rate_table[] = {	/* in KHZ */
>>>> +	9600,
>>>> +	10000,
>>>> +	12000,
>>>> +	19200,
>>>> +	20000,
>>>> +	24000,
>>>> +	25000,
>>>> +	26000,
>>>> +	38400,
>>>> +	40000,
>>>> +	58000,
>>>> +	50000,
>>>> +	52000,
>>>> +};
>>>> +
>>>> +static inline u32 dwc3_ti_readl(struct dwc3_data *data, u32 offset)
>>>> +{
>>>> +	return readl((data->usbss) + offset);
>>>> +}
>>>> +
>>>> +static inline void dwc3_ti_writel(struct dwc3_data *data, u32 offset, u32 value)
>>>> +{
>>>> +	writel(value, (data->usbss) + offset);
>>>> +}
>>>> +
>>>> +static void connect_detect_work(struct work_struct *work)
>>>> +{
>>>> +	struct dwc3_data *data =
>>>> +		container_of(work, struct dwc3_data, work);
>>>> +	u32 vbus_state, reg;
>>>> +	int connect = 0;
>>>> +
>>>> +	/* Read the status for VBUS valid register */
>>>> +	vbus_state = dwc3_ti_readl(data, USBSS_VBUS_STAT);
>>>> +	vbus_state &= USBSS_VBUS_STAT_VBUSVALID;
>>>> +
>>>> +	if (vbus_state)
>>>> +		connect = 1;
>>>> +
>>>> +	/* Set or clear mode valid bit based on connect or disconnect event */
>>>> +	if (data->connect != connect) {
>>>> +		reg = dwc3_ti_readl(data, USBSS_MODE_CONTROL);
>>>> +		if (connect)
>>>> +			reg |= USBSS_MODE_VALID;
>>>> +		else
>>>> +			reg &= ~USBSS_MODE_VALID;
>>>> +
>>>> +		dwc3_ti_writel(data, USBSS_MODE_CONTROL, reg);
>>>> +		data->connect = connect;
>>>> +	}
>>>> +}
>>>> +
>>>> +static irqreturn_t connect_detect_irq_handler(int irq, void *dev_id)
>>>> +{
>>>> +	struct dwc3_data *data = dev_id;
>>>> +	u32 reg;
>>>> +
>>>> +	/* Clear VBUS interrupt always to aviod queuing up redundant work items */
>>>> +	reg = dwc3_ti_readl(data, USBSS_IRQ_MISC_STATUS);
>>>> +	reg |= USBSS_IRQ_MISC_VBUSVALID;
>>>> +	dwc3_ti_writel(data, USBSS_IRQ_MISC_STATUS, reg);
>>>> +
>>>> +	queue_work(system_power_efficient_wq, &data->work);
>>>> +
>>>> +	reg = dwc3_ti_readl(data, USBSS_IRQ_MISC_EOI);
>>>> +	reg &= ~USBSS_IRQ_MISC_EOI_VECTOR;
>>>> +	dwc3_ti_writel(data, USBSS_IRQ_MISC_EOI, reg);
>>>> +	return IRQ_HANDLED;
>>>> +}
>>>> +
>>>> +static int dwc3_ti_vbus_irq_setup(struct platform_device *pdev)
>>>> +{
>>>> +	struct device *dev = &pdev->dev;
>>>> +	struct dwc3_data *data = platform_get_drvdata(pdev);
>>>> +	int irq, ret;
>>>> +
>>>> +	/* Get the misc interrupt */
>>>> +	irq = platform_get_irq(pdev, 0);
>>>> +	if (irq < 0)
>>>> +		return irq;
>>>> +
>>>> +	ret = devm_request_irq(dev, irq, connect_detect_irq_handler, IRQF_SHARED,
>>>> +			       dev_name(dev), data);
>>>> +	if (ret) {
>>>> +		dev_err(dev, "failed to required IRQ #%d-->%d\n",
>>>> +			irq, ret);
>>>> +		return ret;
>>>> +	}
>>>> +
>>>> +	data->vbus_irq = irq;
>>>> +
>>>> +	return 0;
>>>> +}
>>>> +
>>>> +static int phy_syscon_pll_refclk(struct dwc3_data *data)
>>>> +{
>>>> +	struct device *dev = data->dev;
>>>> +	struct device_node *node = dev->of_node;
>>>> +	struct of_phandle_args args;
>>>> +	struct regmap *syscon;
>>>> +	int ret;
>>>> +
>>>> +	syscon = syscon_regmap_lookup_by_phandle(node, "ti,syscon-phy-pll-refclk");
>>>> +	if (IS_ERR(syscon)) {
>>>> +		dev_err(dev, "unable to get ti,syscon-phy-pll-refclk regmap\n");
>>>> +		return PTR_ERR(syscon);
>>>> +	}
>>>> +
>>>> +	data->syscon = syscon;
>>>> +
>>>> +	ret = of_parse_phandle_with_fixed_args(node, "ti,syscon-phy-pll-refclk", 1,
>>>> +					       0, &args);
>>>> +	if (ret)
>>>> +		return ret;
>>>> +
>>>> +	data->offset = args.args[0];
>>>> +
>>>> +	ret = regmap_update_bits(data->syscon, data->offset, PHY_PLL_REFCLK_MASK, data->rate_code);
>>>> +	if (ret) {
>>>> +		dev_err(dev, "failed to set phy pll reference clock rate\n");
>>>> +		return ret;
>>>> +	}
>>>> +
>>>> +	return 0;
>>>> +}
>>>> +
>>>> +static void dwc3_ti_enable_irqs(struct dwc3_data *data)
>>>> +{
>>>> +	u32 reg;
>>>> +
>>>> +	/* enable VBUSVALID interrupt */
>>>> +	reg = dwc3_ti_readl(data, USBSS_IRQ_MISC_ENABLE_SET);
>>>> +	reg |= USBSS_IRQ_MISC_ENABLE_SET_VBUSVALID;
>>>> +	dwc3_ti_writel(data, USBSS_IRQ_MISC_ENABLE_SET, reg);
>>>> +}
>>>> +
>>>> +static void dwc3_ti_disable_irqs(struct dwc3_data *data)
>>>> +{
>>>> +	u32 reg;
>>>> +
>>>> +	/* disable VBUSVALID interrupt */
>>>> +	reg = dwc3_ti_readl(data, USBSS_IRQ_MISC_ENABLE_CLR);
>>>> +	reg |= USBSS_IRQ_MISC_ENABLE_CLR_VBUSVALID;
>>>> +	dwc3_ti_writel(data, USBSS_IRQ_MISC_ENABLE_CLR, reg);
>>>> +}
>>>> +
>>>> +static int dwc3_ti_probe(struct platform_device *pdev)
>>>> +{
>>>> +	struct device *dev = &pdev->dev;
>>>> +	struct device_node *node = pdev->dev.of_node;
>>>> +	struct dwc3_data *data;
>>>> +	int i, ret;
>>>> +	unsigned long rate;
>>>> +	u32 reg;
>>>> +
>>>> +	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
>>>> +	if (!data)
>>>> +		return -ENOMEM;
>>>> +
>>>> +	data->dev = dev;
>>>> +	platform_set_drvdata(pdev, data);
>>>> +
>>>> +	data->usbss = devm_platform_ioremap_resource(pdev, 0);
>>>> +	if (IS_ERR(data->usbss)) {
>>>> +		dev_err(dev, "can't map IOMEM resource\n");
>>>> +		return PTR_ERR(data->usbss);
>>>> +	}
>>>> +
>>>> +	data->usb2_refclk = devm_clk_get(dev, "ref");
>>>> +	if (IS_ERR(data->usb2_refclk)) {
>>>> +		dev_err(dev, "can't get usb2_refclk\n");
>>>> +		return PTR_ERR(data->usb2_refclk);
>>>> +	}
>>>> +
>>>> +	/* Calculate the rate code */
>>>> +	rate = clk_get_rate(data->usb2_refclk);
>>>> +	rate /= 1000;	// To KHz
>>>> +	for (i = 0; i < ARRAY_SIZE(dwc3_ti_rate_table); i++) {
>>>> +		if (dwc3_ti_rate_table[i] == rate)
>>>> +			break;
>>>> +	}
>>>> +
>>>> +	if (i == ARRAY_SIZE(dwc3_ti_rate_table)) {
>>>> +		dev_err(dev, "unsupported usb2_refclk rate: %lu KHz\n", rate);
>>>> +		ret = -EINVAL;
>>>> +		goto err_clk_disable;
>>>> +	}
>>>> +
>>>> +	data->rate_code = i;
>>>> +
>>>> +	/* Read the syscon property and set the rate code */
>>>> +	ret = phy_syscon_pll_refclk(data);
>>>> +	if (ret)
>>>> +		goto err_clk_disable;
>>>> +
>>>> +	/* VBUS divider select */
>>>> +	data->vbus_divider = device_property_read_bool(dev, "ti,vbus-divider");
>>>> +	reg = dwc3_ti_readl(data, USBSS_PHY_CONFIG);
>>>> +	if (data->vbus_divider)
>>>> +		reg |= 1 << USBSS_PHY_VBUS_SEL_SHIFT;
>>>> +
>>>> +	dwc3_ti_writel(data, USBSS_PHY_CONFIG, reg);
>>>> +
>>>> +	/* Initialize a work queue */
>>>> +	ret = devm_work_autocancel(dev, &data->work, connect_detect_work);
>>>> +	if (ret)
>>>> +		goto err_clk_disable;
>>>> +
>>>> +	/* Read and set VBUS IRQ */
>>>> +	ret = dwc3_ti_vbus_irq_setup(pdev);
>>>> +	if (ret)
>>>> +		goto err_clk_disable;
>>>> +
>>>> +	pm_runtime_set_active(dev);
>>>> +	pm_runtime_enable(dev);
>>>> +	/*
>>>> +	 * Don't ignore its dependencies with its children
>>>> +	 */
>>>> +	pm_suspend_ignore_children(dev, false);
>>>> +	clk_prepare_enable(data->usb2_refclk);
>>>> +	pm_runtime_get_noresume(dev);
>>>> +
>>>> +	ret = of_platform_populate(node, NULL, NULL, dev);
>>>> +	if (ret) {
>>>> +		dev_err(dev, "failed to create dwc3 core: %d\n", ret);
>>>> +		goto err_pm_disable;
>>>> +	}
>>>> +
>>>> +	/* Enable vbus irq */
>>>> +	dwc3_ti_enable_irqs(data);
>>>> +
>>>> +	connect_detect_work(&data->work);
>>>> +
>>>> +	/* Setting up autosuspend */
>>>> +	pm_runtime_set_autosuspend_delay(dev, DWC3_AM62_AUTOSUSPEND_DELAY);
>>>> +	pm_runtime_use_autosuspend(dev);
>>>> +	pm_runtime_mark_last_busy(dev);
>>>> +	pm_runtime_put_autosuspend(dev);
>>>> +	return 0;
>>>> +
>>>> +err_pm_disable:
>>>> +	clk_disable_unprepare(data->usb2_refclk);
>>>> +	pm_runtime_disable(dev);
>>>> +	pm_runtime_set_suspended(dev);
>>>> +err_clk_disable:
>>>> +	clk_put(data->usb2_refclk);
>>>> +	return ret;
>>>> +}
>>>> +
>>>> +static int dwc3_ti_remove_core(struct device *dev, void *c)
>>>> +{
>>>> +	struct platform_device *pdev = to_platform_device(dev);
>>>> +
>>>> +	platform_device_unregister(pdev);
>>>> +	return 0;
>>>> +}
>>>> +
>>>> +static int dwc3_ti_remove(struct platform_device *pdev)
>>>> +{
>>>> +	struct device *dev = &pdev->dev;
>>>> +	struct dwc3_data *data = platform_get_drvdata(pdev);
>>>> +	u32 reg;
>>>> +
>>>> +	dwc3_ti_disable_irqs(data);
>>>> +
>>>> +	device_for_each_child(dev, NULL, dwc3_ti_remove_core);
>>>> +
>>>> +	/* Clear mode valid bit */
>>>> +	reg = dwc3_ti_readl(data, USBSS_MODE_CONTROL);
>>>> +	reg &= ~USBSS_MODE_VALID;
>>>> +	dwc3_ti_writel(data, USBSS_MODE_CONTROL, reg);
>>>> +
>>>> +	pm_runtime_put_sync(dev);
>>>> +	clk_disable_unprepare(data->usb2_refclk);
>>>> +	pm_runtime_disable(dev);
>>>> +	pm_runtime_set_suspended(dev);
>>>> +
>>>> +	clk_put(data->usb2_refclk);
>>>> +	platform_set_drvdata(pdev, NULL);
>>>> +	return 0;
>>>> +}
>>>> +
>>>> +#ifdef CONFIG_PM
>>>> +static int dwc3_ti_suspend_common(struct device *dev)
>>>> +{
>>>> +	struct dwc3_data *data = dev_get_drvdata(dev);
>>>> +
>>>> +	/* disable irqs */
>>>> +	dwc3_ti_disable_irqs(data);
>>>> +
>>>> +	clk_disable_unprepare(data->usb2_refclk);
>>>> +
>>>> +	return 0;
>>>> +}
>>>> +
>>>> +static int dwc3_ti_resume_common(struct device *dev)
>>>> +{
>>>> +	struct dwc3_data *data = dev_get_drvdata(dev);
>>>> +
>>>> +	clk_prepare_enable(data->usb2_refclk);
>>>> +
>>>> +	/* Enable irqs */
>>>> +	dwc3_ti_enable_irqs(data);
>>>> +
>>>> +	return 0;
>>>> +}
>>>> +
>>>> +static UNIVERSAL_DEV_PM_OPS(dwc3_ti_pm_ops, dwc3_ti_suspend_common,
>>>> +			    dwc3_ti_resume_common, NULL);
>>>> +
>>>> +#define DEV_PM_OPS	(&dwc3_ti_pm_ops)
>>>> +#else
>>>> +#define DEV_PM_OPS	NULL
>>>> +#endif /* CONFIG_PM */
>>>> +
>>>> +static const struct of_device_id dwc3_ti_of_match[] = {
>>>> +	{ .compatible = "ti,am62-usb"},
>>>> +	{},
>>>> +};
>>>> +MODULE_DEVICE_TABLE(of, dwc3_ti_of_match);
>>>> +
>>>> +static struct platform_driver dwc3_ti_driver = {
>>>> +	.probe		= dwc3_ti_probe,
>>>> +	.remove		= dwc3_ti_remove,
>>>> +	.driver		= {
>>>> +		.name	= "dwc3-am62",
>>>> +		.pm	= DEV_PM_OPS,
>>>> +		.of_match_table = dwc3_ti_of_match,
>>>> +	},
>>>> +};
>>>> +
>>>> +module_platform_driver(dwc3_ti_driver);
>>>> +
>>>> +MODULE_ALIAS("platform:dwc3-am62");
>>>> +MODULE_AUTHOR("Aswath Govindraju <a-govindraju@...com>");
>>>> +MODULE_LICENSE("GPL");
>>>> +MODULE_DESCRIPTION("DesignWare USB3 TI Glue Layer")
> 
> 

Powered by blists - more mailing lists