| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20220420155616.281730-1-matthias.schiffer@ew.tq-group.com>
Date: Wed, 20 Apr 2022 17:56:15 +0200
From: Matthias Schiffer <matthias.schiffer@...tq-group.com>
To: Mark Brown <broonie@...nel.org>
Cc: Pratyush Yadav <p.yadav@...com>,
Tudor Ambarus <tudor.ambarus@...rochip.com>,
Vignesh Raghavendra <vigneshr@...com>,
Ramuthevar Vadivel Murugan
<vadivel.muruganx.ramuthevar@...ux.intel.com>,
linux-spi@...r.kernel.org, linux-kernel@...r.kernel.org,
Matthias Schiffer <matthias.schiffer@...tq-group.com>
Subject: [PATCH v2 1/2] spi: cadence-quadspi: drop cqspi_set_protocol()
As suggested, this removes the whole cqspi_set_protocol() function, as it
is not actually needed:
- Checks for unsupported operations are already handled by supports_op(),
removing the need to distinguish DTR and non-DTR modes in the buswidth
setup
- supports_op() ensures that the DTR flags match for all relevant parts of
an operation, so op->cmd.dtr can be used instead of copying the flag to
the cqspi_flash_pdata
- The logic in cqspi_set_protocol() is moved to cqspi_calc_rdreg() and
cqspi_write_setup() (with a helper macro CQSPI_OP_WIDTH())
The helper macro checks nbytes instead of buswidth for 0, for consistency
with supports_op() etc.
Suggested-by: Pratyush Yadav <p.yadav@...com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@...tq-group.com>
---
v2: remove cqspi_set_protocol() instead of simplifying it
drivers/spi/spi-cadence-quadspi.c | 130 +++++++-----------------------
1 file changed, 27 insertions(+), 103 deletions(-)
diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
index 19686fb47bb3..8c12c6dd58ae 100644
--- a/drivers/spi/spi-cadence-quadspi.c
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -43,6 +43,8 @@
/* Capabilities */
#define CQSPI_SUPPORTS_OCTAL BIT(0)
+#define CQSPI_OP_WIDTH(part) ((part).nbytes ? ilog2((part).buswidth) : 0)
+
struct cqspi_st;
struct cqspi_flash_pdata {
@@ -53,10 +55,6 @@ struct cqspi_flash_pdata {
u32 tsd2d_ns;
u32 tchsh_ns;
u32 tslch_ns;
- u8 inst_width;
- u8 addr_width;
- u8 data_width;
- bool dtr;
u8 cs;
};
@@ -343,18 +341,18 @@ static irqreturn_t cqspi_irq_handler(int this_irq, void *dev)
return IRQ_HANDLED;
}
-static unsigned int cqspi_calc_rdreg(struct cqspi_flash_pdata *f_pdata)
+static unsigned int cqspi_calc_rdreg(const struct spi_mem_op *op)
{
u32 rdreg = 0;
- rdreg |= f_pdata->inst_width << CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB;
- rdreg |= f_pdata->addr_width << CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB;
- rdreg |= f_pdata->data_width << CQSPI_REG_RD_INSTR_TYPE_DATA_LSB;
+ rdreg |= CQSPI_OP_WIDTH(op->cmd) << CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB;
+ rdreg |= CQSPI_OP_WIDTH(op->addr) << CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB;
+ rdreg |= CQSPI_OP_WIDTH(op->data) << CQSPI_REG_RD_INSTR_TYPE_DATA_LSB;
return rdreg;
}
-static unsigned int cqspi_calc_dummy(const struct spi_mem_op *op, bool dtr)
+static unsigned int cqspi_calc_dummy(const struct spi_mem_op *op)
{
unsigned int dummy_clk;
@@ -362,66 +360,12 @@ static unsigned int cqspi_calc_dummy(const struct spi_mem_op *op, bool dtr)
return 0;
dummy_clk = op->dummy.nbytes * (8 / op->dummy.buswidth);
- if (dtr)
+ if (op->cmd.dtr)
dummy_clk /= 2;
return dummy_clk;
}
-static int cqspi_set_protocol(struct cqspi_flash_pdata *f_pdata,
- const struct spi_mem_op *op)
-{
- /*
- * For an op to be DTR, cmd phase along with every other non-empty
- * phase should have dtr field set to 1. If an op phase has zero
- * nbytes, ignore its dtr field; otherwise, check its dtr field.
- */
- f_pdata->dtr = op->cmd.dtr &&
- (!op->addr.nbytes || op->addr.dtr) &&
- (!op->data.nbytes || op->data.dtr);
-
- f_pdata->inst_width = 0;
- if (op->cmd.buswidth)
- f_pdata->inst_width = ilog2(op->cmd.buswidth);
-
- f_pdata->addr_width = 0;
- if (op->addr.buswidth)
- f_pdata->addr_width = ilog2(op->addr.buswidth);
-
- f_pdata->data_width = 0;
- if (op->data.buswidth)
- f_pdata->data_width = ilog2(op->data.buswidth);
-
- /* Right now we only support 8-8-8 DTR mode. */
- if (f_pdata->dtr) {
- switch (op->cmd.buswidth) {
- case 0:
- case 8:
- break;
- default:
- return -EINVAL;
- }
-
- switch (op->addr.buswidth) {
- case 0:
- case 8:
- break;
- default:
- return -EINVAL;
- }
-
- switch (op->data.buswidth) {
- case 0:
- case 8:
- break;
- default:
- return -EINVAL;
- }
- }
-
- return 0;
-}
-
static int cqspi_wait_idle(struct cqspi_st *cqspi)
{
const unsigned int poll_idle_retry = 3;
@@ -503,8 +447,7 @@ static int cqspi_setup_opcode_ext(struct cqspi_flash_pdata *f_pdata,
}
static int cqspi_enable_dtr(struct cqspi_flash_pdata *f_pdata,
- const struct spi_mem_op *op, unsigned int shift,
- bool enable)
+ const struct spi_mem_op *op, unsigned int shift)
{
struct cqspi_st *cqspi = f_pdata->cqspi;
void __iomem *reg_base = cqspi->iobase;
@@ -517,7 +460,7 @@ static int cqspi_enable_dtr(struct cqspi_flash_pdata *f_pdata,
* We enable dual byte opcode here. The callers have to set up the
* extension opcode based on which type of operation it is.
*/
- if (enable) {
+ if (op->cmd.dtr) {
reg |= CQSPI_REG_CONFIG_DTR_PROTO;
reg |= CQSPI_REG_CONFIG_DUAL_OPCODE;
@@ -549,12 +492,7 @@ static int cqspi_command_read(struct cqspi_flash_pdata *f_pdata,
size_t read_len;
int status;
- status = cqspi_set_protocol(f_pdata, op);
- if (status)
- return status;
-
- status = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_STIG_LSB,
- f_pdata->dtr);
+ status = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_STIG_LSB);
if (status)
return status;
@@ -565,17 +503,17 @@ static int cqspi_command_read(struct cqspi_flash_pdata *f_pdata,
return -EINVAL;
}
- if (f_pdata->dtr)
+ if (op->cmd.dtr)
opcode = op->cmd.opcode >> 8;
else
opcode = op->cmd.opcode;
reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB;
- rdreg = cqspi_calc_rdreg(f_pdata);
+ rdreg = cqspi_calc_rdreg(op);
writel(rdreg, reg_base + CQSPI_REG_RD_INSTR);
- dummy_clk = cqspi_calc_dummy(op, f_pdata->dtr);
+ dummy_clk = cqspi_calc_dummy(op);
if (dummy_clk > CQSPI_DUMMY_CLKS_MAX)
return -EOPNOTSUPP;
@@ -622,12 +560,7 @@ static int cqspi_command_write(struct cqspi_flash_pdata *f_pdata,
size_t write_len;
int ret;
- ret = cqspi_set_protocol(f_pdata, op);
- if (ret)
- return ret;
-
- ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_STIG_LSB,
- f_pdata->dtr);
+ ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_STIG_LSB);
if (ret)
return ret;
@@ -638,10 +571,10 @@ static int cqspi_command_write(struct cqspi_flash_pdata *f_pdata,
return -EINVAL;
}
- reg = cqspi_calc_rdreg(f_pdata);
+ reg = cqspi_calc_rdreg(op);
writel(reg, reg_base + CQSPI_REG_RD_INSTR);
- if (f_pdata->dtr)
+ if (op->cmd.dtr)
opcode = op->cmd.opcode >> 8;
else
opcode = op->cmd.opcode;
@@ -688,21 +621,20 @@ static int cqspi_read_setup(struct cqspi_flash_pdata *f_pdata,
int ret;
u8 opcode;
- ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_READ_LSB,
- f_pdata->dtr);
+ ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_READ_LSB);
if (ret)
return ret;
- if (f_pdata->dtr)
+ if (op->cmd.dtr)
opcode = op->cmd.opcode >> 8;
else
opcode = op->cmd.opcode;
reg = opcode << CQSPI_REG_RD_INSTR_OPCODE_LSB;
- reg |= cqspi_calc_rdreg(f_pdata);
+ reg |= cqspi_calc_rdreg(op);
/* Setup dummy clock cycles */
- dummy_clk = cqspi_calc_dummy(op, f_pdata->dtr);
+ dummy_clk = cqspi_calc_dummy(op);
if (dummy_clk > CQSPI_DUMMY_CLKS_MAX)
return -EOPNOTSUPP;
@@ -947,22 +879,21 @@ static int cqspi_write_setup(struct cqspi_flash_pdata *f_pdata,
void __iomem *reg_base = cqspi->iobase;
u8 opcode;
- ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_WRITE_LSB,
- f_pdata->dtr);
+ ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_WRITE_LSB);
if (ret)
return ret;
- if (f_pdata->dtr)
+ if (op->cmd.dtr)
opcode = op->cmd.opcode >> 8;
else
opcode = op->cmd.opcode;
/* Set opcode. */
reg = opcode << CQSPI_REG_WR_INSTR_OPCODE_LSB;
- reg |= f_pdata->data_width << CQSPI_REG_WR_INSTR_TYPE_DATA_LSB;
- reg |= f_pdata->addr_width << CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB;
+ reg |= CQSPI_OP_WIDTH(op->data) << CQSPI_REG_WR_INSTR_TYPE_DATA_LSB;
+ reg |= CQSPI_OP_WIDTH(op->addr) << CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB;
writel(reg, reg_base + CQSPI_REG_WR_INSTR);
- reg = cqspi_calc_rdreg(f_pdata);
+ reg = cqspi_calc_rdreg(op);
writel(reg, reg_base + CQSPI_REG_RD_INSTR);
/*
@@ -1244,10 +1175,6 @@ static ssize_t cqspi_write(struct cqspi_flash_pdata *f_pdata,
const u_char *buf = op->data.buf.out;
int ret;
- ret = cqspi_set_protocol(f_pdata, op);
- if (ret)
- return ret;
-
ret = cqspi_write_setup(f_pdata, op);
if (ret)
return ret;
@@ -1260,7 +1187,7 @@ static ssize_t cqspi_write(struct cqspi_flash_pdata *f_pdata,
* mode. So, we can not use direct mode when in DTR mode for writing
* data.
*/
- if (!f_pdata->dtr && cqspi->use_direct_mode &&
+ if (!op->cmd.dtr && cqspi->use_direct_mode &&
((to + len) <= cqspi->ahb_size)) {
memcpy_toio(cqspi->ahb_base + to, buf, len);
return cqspi_wait_idle(cqspi);
@@ -1348,9 +1275,6 @@ static ssize_t cqspi_read(struct cqspi_flash_pdata *f_pdata,
int ret;
ddata = of_device_get_match_data(dev);
- ret = cqspi_set_protocol(f_pdata, op);
- if (ret)
- return ret;
ret = cqspi_read_setup(f_pdata, op);
if (ret)
--
2.25.1
Powered by blists - more mailing lists