Message-Id: <20220425153650.1.Iedd71976a78d53c301ce0134832de95a989c9195@changeid>
Date:   Mon, 25 Apr 2022 15:36:55 -0700
From:   Douglas Anderson <dianders@...omium.org>
To:     Bjorn Andersson <bjorn.andersson@...aro.org>
Cc:     Kuogee Hsieh <quic_khsieh@...cinc.com>,
        Abhinav Kumar <quic_abhinavk@...cinc.com>,
        Matthias Kaehlcke <mka@...omium.org>,
        Dmitry Baryshkov <dmitry.baryshkov@...aro.org>,
        Stephen Boyd <swboyd@...omium.org>,
        Rob Clark <robdclark@...omium.org>, quic_kalyant@...cinc.com,
        Sankeerth Billakanti <quic_sbillaka@...cinc.com>,
        linux-arm-msm@...r.kernel.org,
        Douglas Anderson <dianders@...omium.org>,
        Andy Gross <agross@...nel.org>,
        Krzysztof Kozlowski <krzk+dt@...nel.org>,
        Rob Herring <robh+dt@...nel.org>, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org
Subject: [PATCH] arm64: dts: qcom: sc7280: eDP for herobrine boards

This change adds in eDP for herobrine boards, splitting up amongst the
different files as makes sense. Rationale for the current split of
things:
* The eDP connector itself is on qcard. However, not all devices with
  a qcard will use an eDP panel. Some might use MIPI and, presumably,
  someone could build a device with qcard that had no display at all.
* The qcard provides a PWM for backlight that goes to the eDP
  connector. This PWM is also is provided to the board and it's
  expected that it would be used as the backlight PWM even for
  herobrine devices with MIPI displays.
* It's currently assumed that all herobrine boards will have some sort
  of display, either MIPI or eDP (but not both).
* We will assume herobrine-rev1 has eDP. The schematics allow for a
  MIPI panel to be hooked up but, aside from some testing, nobody is
  doing this and most boards don't have all the parts stuffed for
  it. The two panels would also share a PWM for backlight, which is
  weird.
* herobrine-villager and herobrine-hoglin (crd) also have eDP.
* herobrine-hoglin (crd) has slightly different regulator setup for
  the backlight. It's expected that this is unique to this board. See
  comments in the dts file.
* There are some regulators that are defined in the qcard schematic
  but provided by the board like "vreg_edp_bl" and
  "vreg_edp_3p3". While we could put references to these regulators
  straight in the qcard.dtsi file, this would force someone using
  qcard that didn't provide those regulators to provide a dummy or do
  an ugly /delete-node/. Instead, we'll add references in
  herobrine.dtsi.

Signed-off-by: Douglas Anderson <dianders@...omium.org>
---
This patch most directly depends on ("arm64: dts: qcom: pm8350c: Add
pwm support") [1] and it won't even compile without that. To be
functional, of course, we also need the driver support for the PWM to
land.

In order for this patch to function we also need Sankeerth's eDP
series [2] to land.

To be schema happy, this patch also relies on my patch to add
regulators into the schema for the PHY an the eDP controller [3].
Several other device tree files reference these supplies without being
in the schema, though, so we'll have to decide whether to block on
those bindings landing. It does sound as if the regulator names may
not be exactly correct right now, though. :(

In theory, I could break this patch up into separate patches adding
the basic support to the qcard, then to herobrine.dtsi, and then one
patch each for herobrine-r1, villager, and crd. Doing so didn't seem
to make sense to me--I think it's easier to make sense of the change
as one patch. However, if someone feels strongly that it should be
broken up I'm happy to do so.

I've managed to get the display on my herobrine-rev1 up and running on
today's linuxnext (next-20220422) with this series. For whatever
reason the eDP PHY wouldn't probe unless I hacked `fw_devlink=off` in
the config. I don't believe that problem is related to this patch,
though.

[1] https://lore.kernel.org/r/1645509309-16142-4-git-send-email-quic_c_skakit@quicinc.com
[2] https://lore.kernel.org/r/1650887072-16652-1-git-send-email-quic_sbillaka@quicinc.com/
[3] https://lore.kernel.org/r/20220425210643.2420919-1-dianders@chromium.org

 .../boot/dts/qcom/sc7280-herobrine-crd.dts    | 40 ++++++++++++++
 .../qcom/sc7280-herobrine-herobrine-r1.dts    |  8 +++
 .../dts/qcom/sc7280-herobrine-villager-r0.dts |  8 +++
 .../arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 30 +++++++++++
 arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi    | 54 +++++++++++++++++++
 5 files changed, 140 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
index b06f61e9b90b..a4ac33c4fd59 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -12,6 +12,27 @@
 / {
 	model = "Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+)";
 	compatible = "google,hoglin", "qcom,sc7280";
+
+	/* FIXED REGULATORS */
+
+	/*
+	 * On most herobrine boards PPVAR_SYS directly provides VREG_EDP_BL.
+	 * However, on CRD there's an extra regulator in the way. Since this
+	 * is expected to be uncommon, we'll leave the "vreg_edp_bl" label
+	 * in the baseboard herobrine.dtsi point at "ppvar_sys" and then
+	 * make a "_crd" specific version here.
+	 */
+	vreg_edp_bl_crd: vreg-edp-bl-crd-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_edp_bl_crd";
+
+		gpio = <&pm8350c_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_bl_reg_en>;
+
+		vin-supply = <&ppvar_sys>;
+	};
 };
 
 /* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
@@ -81,6 +102,14 @@ ap_ts: touchscreen@5c {
 	};
 };
 
+&mdss_edp {
+	status = "okay";
+};
+
+&mdss_edp_phy {
+	status = "okay";
+};
+
 /* For nvme */
 &pcie1 {
 	status = "okay";
@@ -91,6 +120,10 @@ &pcie1_phy {
 	status = "okay";
 };
 
+&pm8350c_pwm_backlight {
+	power-supply = <&vreg_edp_bl_crd>;
+};
+
 /* For eMMC */
 &sdhc_1 {
 	status = "okay";
@@ -121,6 +154,13 @@ &pm8350c_gpios {
 			  "PMIC_EDP_BL_EN",
 			  "PMIC_EDP_BL_PWM",
 			  "";
+
+	edp_bl_reg_en: edp-bl-reg-en {
+		pins = "gpio6";
+		function = "normal";
+		bias-disable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
 };
 
 &tlmm {
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
index 29c4ca095294..b69ca09d9bfb 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
@@ -100,6 +100,14 @@ ap_ts: touchscreen@5c {
 	};
 };
 
+&mdss_edp {
+	status = "okay";
+};
+
+&mdss_edp_phy {
+	status = "okay";
+};
+
 /* For nvme */
 &pcie1 {
 	status = "okay";
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
index 6c2b9a14535a..d3d6ffad4eff 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
@@ -58,6 +58,14 @@ &ap_sar_sensor1 {
 	status = "okay";
 };
 
+&mdss_edp {
+	status = "okay";
+};
+
+&mdss_edp_phy {
+	status = "okay";
+};
+
 /* For nvme */
 &pcie1 {
 	status = "okay";
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
index d58045dd7334..769d440d1917 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
@@ -367,6 +367,14 @@ &vreg_l2c_1p8 {
 
 /* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
 
+&edp_panel {
+	/*
+	 * Now that we've defined which power supply we give to qcard for
+	 * eDP we can hook it up in the panel node.
+	 */
+	power-supply = <&vreg_edp_3p3>;
+};
+
 ap_sar_sensor_i2c: &i2c1 {
 	clock-frequency = <400000>;
 	status = "disabled";
@@ -420,6 +428,14 @@ tpm@50 {
 	};
 };
 
+&mdss {
+	status = "okay";
+};
+
+&mdss_mdp {
+	status = "okay";
+};
+
 /* NVMe drive, enabled on a per-board basis */
 &pcie1 {
 	pinctrl-names = "default";
@@ -429,6 +445,20 @@ &pcie1 {
 	vddpe-3v3-supply = <&pp3300_ssd>;
 };
 
+&pm8350c_pwm {
+	status = "okay";
+};
+
+&pm8350c_pwm_backlight {
+	status = "okay";
+
+	/*
+	 * Now that we've defined which power supply we give to qcard for
+	 * backlight we can hook it up in the panel node.
+	 */
+	power-supply = <&vreg_edp_bl>;
+};
+
 &pmk8350_rtc {
 	status = "disabled";
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
index b833ba1e8f4a..fbd9f9fa9d3a 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
@@ -29,6 +29,16 @@ aliases {
 		serial0 = &uart5;
 		serial1 = &uart7;
 	};
+
+	pm8350c_pwm_backlight: backlight {
+		compatible = "pwm-backlight";
+		status = "disabled";
+
+		enable-gpios = <&pm8350c_gpios 7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_edp_bl_en>;
+		pwms = <&pm8350c_pwm 3 65535>;
+	};
 };
 
 &apps_rsc {
@@ -293,11 +303,50 @@ &ipa {
 	modem-init;
 };
 
+/* NOTE: Not all Qcards have eDP connector stuffed */
+&mdss_edp {
+	vdda-0p9-supply = <&vdd_a_edp_0_0p9>;
+	vdda-1p2-supply = <&vdd_a_edp_0_1p2>;
+
+	aux-bus {
+		edp_panel: panel {
+			compatible = "edp-panel";
+
+			backlight = <&pm8350c_pwm_backlight>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					edp_panel_in: endpoint {
+						remote-endpoint = <&mdss_edp_out>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&mdss_edp_out {
+	remote-endpoint = <&edp_panel_in>;
+};
+
+&mdss_edp_phy {
+	vdda-pll-supply = <&vdd_a_edp_0_0p9>;
+	vdda-phy-supply = <&vdd_a_edp_0_1p2>;
+};
+
 &pcie1_phy {
 	vdda-phy-supply = <&vreg_l10c_0p88>;
 	vdda-pll-supply = <&vreg_l6b_1p2>;
 };
 
+&pm8350c_pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pmic_edp_bl_pwm>;
+};
+
 &pmk8350_vadc {
 	pmk8350-die-temp@3 {
 		reg = <PMK8350_ADC7_DIE_TEMP>;
@@ -383,6 +432,11 @@ &usb_2_hsphy {
  * baseboard or board device tree, not here.
  */
 
+/* No external pull for eDP HPD, so set the internal one. */
+&edp_hot_plug_det {
+	bias-pull-down;
+};
+
 /*
  * For ts_i2c
  *
-- 
2.36.0.rc2.479.g8af0fa9b8e-goog

Powered by blists - more mailing lists