lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <f4c2ad78-0b9e-c5da-e0a4-69f836e87b11@codethink.co.uk>
Date:   Tue, 7 Jun 2022 16:18:50 +0100
From:   Ben Dooks <ben.dooks@...ethink.co.uk>
To:     Conor Dooley <conor.dooley@...rochip.com>, Bin Liu <b-liu@...com>,
        Greg Kroah-Hartman <gregkh@...uxfoundation.org>
Cc:     Daire McNamara <daire.mcnamara@...rochip.com>,
        Valentina Fernandez <valentina.fernandezalanis@...rochip.com>,
        linux-kernel@...r.kernel.org, linux-usb@...r.kernel.org,
        linux-riscv@...ts.infradead.org
Subject: Re: [PATCH 1/3] usb: musb: Add support for PolarFire SoC's musb
 controller

On 07/06/2022 14:22, Conor Dooley wrote:
> Add support for Microchips's PolarFire SoC's musb controller in host,
> peripheral and otg mode.
> 
> Tested-by: Valentina Fernandez <valentina.fernandezalanis@...rochip.com>
> Signed-off-by: Conor Dooley <conor.dooley@...rochip.com>
> ---
>   drivers/usb/musb/Kconfig  |  13 +-
>   drivers/usb/musb/Makefile |   1 +
>   drivers/usb/musb/mpfs.c   | 285 ++++++++++++++++++++++++++++++++++++++
>   3 files changed, 298 insertions(+), 1 deletion(-)
>   create mode 100644 drivers/usb/musb/mpfs.c
> 
> diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig
> index 4d61df6a9b5c..f906dfd360d3 100644
> --- a/drivers/usb/musb/Kconfig
> +++ b/drivers/usb/musb/Kconfig
> @@ -123,6 +123,17 @@ config USB_MUSB_MEDIATEK
>   	select GENERIC_PHY
>   	select USB_ROLE_SWITCH
>   
> +config USB_MUSB_POLARFIRE_SOC
> +	tristate "Microchip PolarFire SoC platforms"
> +	depends on SOC_MICROCHIP_POLARFIRE || COMPILE_TEST
> +	depends on NOP_USB_XCEIV
> +	select USB_MUSB_DUAL_ROLE
> +	help
> +	  Say Y here to enable support for USB on Microchip's PolarFire SoC.
> +
> +	  This support is also available as a module.  If so, the module
> +	  will be called mpfs.
> +
>   comment "MUSB DMA mode"
>   
>   config MUSB_PIO_ONLY
> @@ -146,7 +157,7 @@ config USB_UX500_DMA
>   
>   config USB_INVENTRA_DMA
>   	bool 'Inventra'
> -	depends on USB_MUSB_OMAP2PLUS || USB_MUSB_MEDIATEK || USB_MUSB_JZ4740
> +	depends on USB_MUSB_OMAP2PLUS || USB_MUSB_MEDIATEK || USB_MUSB_JZ4740 || USB_MUSB_POLARFIRE_SOC
>   	help
>   	  Enable DMA transfers using Mentor's engine.
>   
> diff --git a/drivers/usb/musb/Makefile b/drivers/usb/musb/Makefile
> index 932247360a9f..51dd54a8de49 100644
> --- a/drivers/usb/musb/Makefile
> +++ b/drivers/usb/musb/Makefile
> @@ -25,6 +25,7 @@ obj-$(CONFIG_USB_MUSB_UX500)			+= ux500.o
>   obj-$(CONFIG_USB_MUSB_JZ4740)			+= jz4740.o
>   obj-$(CONFIG_USB_MUSB_SUNXI)			+= sunxi.o
>   obj-$(CONFIG_USB_MUSB_MEDIATEK)      		+= mediatek.o
> +obj-$(CONFIG_USB_MUSB_POLARFIRE_SOC)		+= mpfs.o
>   
>   # the kconfig must guarantee that only one of the
>   # possible I/O schemes will be enabled at a time ...
> diff --git a/drivers/usb/musb/mpfs.c b/drivers/usb/musb/mpfs.c
> new file mode 100644
> index 000000000000..2b3dda335783
> --- /dev/null
> +++ b/drivers/usb/musb/mpfs.c
> @@ -0,0 +1,285 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * PolarFire SoC (MPFS) MUSB Glue Layer
> + *
> + * Copyright (c) 2020-2022 Microchip Corporation. All rights reserved.
> + * Based on {omap2430,tusb6010,ux500}.c
> + *
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/usb/usb_phy_generic.h>
> +#include "musb_core.h"
> +#include "musb_dma.h"
> +
> +#define MPFS_MUSB_MAX_EP_NUM	8
> +#define MPFS_MUSB_RAM_BITS	12
> +
> +struct mpfs_glue {
> +	struct device *dev;
> +	struct platform_device *musb;
> +	struct platform_device *phy;
> +	struct clk *clk;
> +};
> +
> +static struct musb_fifo_cfg mpfs_musb_mode_cfg[] = {
> +	{ .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, },
> +	{ .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, },
> +	{ .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, },
> +	{ .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, },
> +	{ .hw_ep_num = 3, .style = FIFO_TX, .maxpacket = 512, },
> +	{ .hw_ep_num = 3, .style = FIFO_RX, .maxpacket = 512, },
> +	{ .hw_ep_num = 4, .style = FIFO_TX, .maxpacket = 1024, },
> +	{ .hw_ep_num = 4, .style = FIFO_RX, .maxpacket = 4096, },
> +};
> +
> +static const struct musb_hdrc_config mpfs_musb_hdrc_config = {
> +	.fifo_cfg = mpfs_musb_mode_cfg,
> +	.fifo_cfg_size = ARRAY_SIZE(mpfs_musb_mode_cfg),
> +	.multipoint = true,
> +	.dyn_fifo = true,
> +	.num_eps = MPFS_MUSB_MAX_EP_NUM,
> +	.ram_bits = MPFS_MUSB_RAM_BITS,
> +};
> +
> +static irqreturn_t mpfs_musb_interrupt(int irq, void *__hci)
> +{
> +	unsigned long flags;
> +	irqreturn_t ret = IRQ_NONE;
> +	struct musb *musb = __hci;
> +
> +	spin_lock_irqsave(&musb->lock, flags);
> +
> +	musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
> +	musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX);
> +	musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX);
> +
> +	if (musb->int_usb || musb->int_tx || musb->int_rx) {
> +		musb_writeb(musb->mregs, MUSB_INTRUSB, musb->int_usb);
> +		musb_writew(musb->mregs, MUSB_INTRTX, musb->int_tx);
> +		musb_writew(musb->mregs, MUSB_INTRRX, musb->int_rx);
> +		ret = musb_interrupt(musb);
> +	}
> +
> +	spin_unlock_irqrestore(&musb->lock, flags);
> +
> +	return ret;
> +}
> +
> +static void mpfs_musb_set_vbus(struct musb *musb, int is_on)
> +{
> +	u8 devctl;
> +
> +	/*
> +	 * HDRC controls CPEN, but beware current surges during device
> +	 * connect.  They can trigger transient overcurrent conditions
> +	 * that must be ignored.
> +	 */
> +	devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
> +
> +	if (is_on) {
> +		musb->is_active = 1;
> +		musb->xceiv->otg->default_a = 1;
> +		musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
> +		devctl |= MUSB_DEVCTL_SESSION;
> +		MUSB_HST_MODE(musb);
> +	} else {
> +		musb->is_active = 0;
> +
> +		/*
> +		 * NOTE:  skipping A_WAIT_VFALL -> A_IDLE and
> +		 * jumping right to B_IDLE...
> +		 */
> +		musb->xceiv->otg->default_a = 0;
> +		musb->xceiv->otg->state = OTG_STATE_B_IDLE;
> +		devctl &= ~MUSB_DEVCTL_SESSION;
> +
> +		MUSB_DEV_MODE(musb);
> +	}
> +
> +	musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
> +
> +	dev_dbg(musb->controller, "VBUS %s, devctl %02x\n",
> +		usb_otg_state_string(musb->xceiv->otg->state),
> +		musb_readb(musb->mregs, MUSB_DEVCTL));
> +}
> +
> +static int mpfs_musb_init(struct musb *musb)
> +{
> +	struct device *dev = musb->controller;
> +
> +	musb->xceiv = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
> +	if (IS_ERR(musb->xceiv)) {
> +		dev_err(dev, "HS UDC: no transceiver configured\n");
> +		return PTR_ERR(musb->xceiv);
> +	}
> +
> +	musb->dyn_fifo = true;
> +	musb->isr = mpfs_musb_interrupt;
> +
> +	musb_platform_set_vbus(musb, 1);
> +
> +	return 0;
> +}
> +
> +static const struct musb_platform_ops mpfs_ops = {
> +	.quirks		= MUSB_DMA_INVENTRA,
> +	.init		= mpfs_musb_init,
> +	.fifo_mode	= 2,
> +#ifdef CONFIG_USB_INVENTRA_DMA
> +	.dma_init	= musbhs_dma_controller_create,
> +	.dma_exit	= musbhs_dma_controller_destroy,
> +#endif
> +	.set_vbus	= mpfs_musb_set_vbus
> +};
> +
> +static int mpfs_probe(struct platform_device *pdev)
> +{
> +	struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
> +	struct mpfs_glue *glue;
> +	struct platform_device *musb_pdev;
> +	struct device *dev = &pdev->dev;
> +	struct resource musb_resources[3];
> +	struct clk *clk;
> +	int ret;
> +
> +	glue = devm_kzalloc(dev, sizeof(*glue), GFP_KERNEL);
> +	if (!glue)
> +		return -ENOMEM;
> +
> +	musb_pdev = platform_device_alloc("musb-hdrc", PLATFORM_DEVID_AUTO);
> +	if (!musb_pdev) {
> +		dev_err(dev, "failed to allocate musb device\n");
> +		return -ENOMEM;
> +	}
> +
> +	clk = devm_clk_get(&pdev->dev, NULL);
> +	if (IS_ERR(clk)) {
> +		dev_err(&pdev->dev, "failed to get clock\n");
> +		ret = PTR_ERR(clk);
> +		goto err_phy_release;
> +	}
> +
> +	ret = clk_prepare_enable(clk);
> +	if (ret) {
> +		dev_err(&pdev->dev, "failed to enable clock\n");
> +		goto err_phy_release;
> +	}
> +
> +	musb_pdev->dev.parent = dev;
> +	musb_pdev->dev.coherent_dma_mask = DMA_BIT_MASK(39);
> +	musb_pdev->dev.dma_mask = &musb_pdev->dev.coherent_dma_mask;
> +	device_set_of_node_from_dev(&musb_pdev->dev, dev);
> +
> +	glue->dev = dev;
> +	glue->musb = musb_pdev;
> +	glue->clk = clk;
> +
> +	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
> +	if (!pdata)
> +		goto err_clk_disable;
> +
> +	pdata->config = &mpfs_musb_hdrc_config;
> +	pdata->platform_ops = &mpfs_ops;
> +
> +	pdata->mode = usb_get_dr_mode(dev);
> +	if (pdata->mode == USB_DR_MODE_UNKNOWN) {
> +		dev_info(dev, "No dr_mode property found, defaulting to otg\n");
> +		pdata->mode = USB_DR_MODE_OTG;
> +	}
> +
> +	glue->phy = usb_phy_generic_register();
> +	if (IS_ERR(glue->phy)) {
> +		dev_err(dev, "failed to register usb-phy %ld\n",
> +			PTR_ERR(glue->phy));
> +		goto err_clk_disable;
> +	}
> +
> +	platform_set_drvdata(pdev, glue);
> +
> +	memset(musb_resources, 0x00,
> +	       sizeof(*musb_resources) * ARRAY_SIZE(musb_resources));
> +
> +	musb_resources[0].name  = pdev->resource[0].name;
> +	musb_resources[0].start = pdev->resource[0].start;
> +	musb_resources[0].end   = pdev->resource[0].end;
> +	musb_resources[0].flags = pdev->resource[0].flags;
> +
> +	musb_resources[1].name  = pdev->resource[1].name;
> +	musb_resources[1].start = pdev->resource[1].start;
> +	musb_resources[1].end   = pdev->resource[1].end;
> +	musb_resources[1].flags = pdev->resource[1].flags;
> +
> +	musb_resources[2].name  = pdev->resource[2].name;
> +	musb_resources[2].start = pdev->resource[2].start;
> +	musb_resources[2].end   = pdev->resource[2].end;
> +	musb_resources[2].flags = pdev->resource[2].flags;

I wonder if you could memcpy or just use compiler assignment for
these?

> +
> +	ret = platform_device_add_resources(musb_pdev, musb_resources,
> +					    ARRAY_SIZE(musb_resources));
> +	if (ret) {
> +		dev_err(dev, "failed to add resources\n");
> +		goto err_clk_disable;
> +	}
> +
> +	ret = platform_device_add_data(musb_pdev, pdata, sizeof(*pdata));
> +	if (ret) {
> +		dev_err(dev, "failed to add platform_data\n");
> +		goto err_clk_disable;
> +	}
> +
> +	ret = platform_device_add(musb_pdev);
> +	if (ret) {
> +		dev_err(dev, "failed to register musb device\n");
> +		goto err_clk_disable;
> +	}
> +
> +	dev_info(&pdev->dev, "Registered MPFS MUSB driver\n");
> +	return 0;
> +
> +err_clk_disable:
> +	clk_disable_unprepare(clk);
> +
> +err_phy_release:
> +	usb_phy_generic_unregister(glue->phy);
> +	platform_device_put(musb_pdev);
> +	return ret;
> +}
> +
> +static int mpfs_remove(struct platform_device *pdev)
> +{
> +	struct mpfs_glue *glue = platform_get_drvdata(pdev);
> +
> +	platform_device_unregister(glue->musb);
> +	usb_phy_generic_unregister(pdev);
> +
> +	return 0;
> +}
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id mpfs_id_table[] = {
> +	{ .compatible = "microchip,mpfs-musb" },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, mpfs_id_table);
> +#endif
> +
> +static struct platform_driver mpfs_musb_driver = {
> +	.probe = mpfs_probe,
> +	.remove = mpfs_remove,
> +	.driver = {
> +		.name = "mpfs-musb",
> +		.of_match_table = of_match_ptr(mpfs_id_table)
> +	},
> +};
> +
> +module_platform_driver(mpfs_musb_driver);
> +
> +MODULE_DESCRIPTION("PolarFire SoC MUSB Glue Layer");
> +MODULE_LICENSE("GPL");


-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

https://www.codethink.co.uk/privacy.html

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ