| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20220622123557.2av3cfutpnd6iaqf@pali>
Date: Wed, 22 Jun 2022 14:35:57 +0200
From: Pali Rohár <pali@...nel.org>
To: Rob Herring <robh+dt@...nel.org>,
Michael Ellerman <mpe@...erman.id.au>
Cc: devicetree@...r.kernel.org, linuxppc-dev@...ts.ozlabs.org,
linux-kernel@...r.kernel.org, Marek Behun <marek.behun@....cz>,
Josef Schlehofer <josef.schlehofer@....cz>
Subject: Re: [PATCH] powerpc: dts: Add DTS file for CZ.NIC Turris 1.x routers
On Thursday 09 June 2022 12:19:00 Pali Rohár wrote:
> On Tuesday 24 May 2022 11:23:32 Pali Rohár wrote:
> > On Wednesday 11 May 2022 16:37:12 Pali Rohár wrote:
> > > CZ.NIC Turris 1.0 and 1.1 are open source routers, they have dual-core
> > > PowerPC Freescale P2020 CPU and are based on Freescale P2020RDB-PC-A board.
> > > Hardware design is fully open source, all firmware and hardware design
> > > files are available at Turris project website:
> > >
> > > https://docs.turris.cz/hw/turris-1x/turris-1x/
> > > https://project.turris.cz/en/hardware.html
> > >
> > > Signed-off-by: Pali Rohár <pali@...nel.org>
> > > ---
> > > arch/powerpc/boot/dts/turris1x.dts | 470 +++++++++++++++++++++++++++++
> > > 1 file changed, 470 insertions(+)
> > > create mode 100644 arch/powerpc/boot/dts/turris1x.dts
> >
> > Michael, Rob: PING?
>
> PING?
PING?
> > > diff --git a/arch/powerpc/boot/dts/turris1x.dts b/arch/powerpc/boot/dts/turris1x.dts
> > > new file mode 100644
> > > index 000000000000..2a624f117586
> > > --- /dev/null
> > > +++ b/arch/powerpc/boot/dts/turris1x.dts
> > > @@ -0,0 +1,470 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * Turris 1.x Device Tree Source
> > > + *
> > > + * Copyright 2013 - 2022 CZ.NIC z.s.p.o. (http://www.nic.cz/)
> > > + *
> > > + * Pinout, Schematics and Altium hardware design files are open source
> > > + * and available at: https://docs.turris.cz/hw/turris-1x/turris-1x/
> > > + */
> > > +
> > > +#include <dt-bindings/gpio/gpio.h>
> > > +#include <dt-bindings/interrupt-controller/irq.h>
> > > +#include <dt-bindings/leds/common.h>
> > > +/include/ "fsl/p2020si-pre.dtsi"
> > > +
> > > +/ {
> > > + model = "Turris 1.x";
> > > + compatible = "cznic,turris1x", "fsl,P2020RDB-PC"; /* fsl,P2020RDB-PC is required for booting Linux */
> > > +
> > > + aliases {
> > > + ethernet0 = &enet0;
> > > + ethernet1 = &enet1;
> > > + ethernet2 = &enet2;
> > > + serial0 = &serial0;
> > > + serial1 = &serial1;
> > > + pci0 = &pci0;
> > > + pci1 = &pci1;
> > > + pci2 = &pci2;
> > > + spi0 = &spi0;
> > > + };
> > > +
> > > + memory {
> > > + device_type = "memory";
> > > + };
> > > +
> > > + soc: soc@...00000 {
> > > + ranges = <0x0 0x0 0xffe00000 0x00100000>;
> > > +
> > > + i2c@...0 {
> > > + /* PCA9557PW GPIO controller for boot config */
> > > + gpio-controller@18 {
> > > + compatible = "nxp,pca9557";
> > > + label = "bootcfg";
> > > + reg = <0x18>;
> > > + #gpio-cells = <2>;
> > > + gpio-controller;
> > > + polarity = <0x00>;
> > > + };
> > > +
> > > + /* STM32F030R8T6 MCU for power control */
> > > + power-control@32 {
> > > + /*
> > > + * Turris Power Control firmware runs on STM32F0 MCU.
> > > + * This firmware is open source and available at:
> > > + * https://gitlab.nic.cz/turris/hw/turris_power_control
> > > + */
> > > + reg = <0x32>;
> > > + };
> > > +
> > > + /* SA56004ED temperature control */
> > > + temperature-sensor@4c {
> > > + compatible = "nxp,sa56004";
> > > + reg = <0x4c>;
> > > + interrupt-parent = <&gpio>;
> > > + interrupts = <12 IRQ_TYPE_LEVEL_LOW>, /* GPIO12 - ALERT pin */
> > > + <13 IRQ_TYPE_LEVEL_LOW>; /* GPIO13 - CRIT pin */
> > > + };
> > > +
> > > + /* DDR3 SPD/EEPROM */
> > > + eeprom@52 {
> > > + compatible = "atmel,spd";
> > > + reg = <0x52>;
> > > + };
> > > +
> > > + /* ATSHA204-TH-DA-T crypto module */
> > > + crypto@64 {
> > > + compatible = "atmel,atsha204";
> > > + reg = <0x64>;
> > > + };
> > > +
> > > + /* IDT6V49205BNLGI clock generator */
> > > + clock-generator@69 {
> > > + compatible = "idt,6v49205b";
> > > + reg = <0x69>;
> > > + };
> > > +
> > > + /* MCP79402-I/ST Protected EEPROM */
> > > + eeprom@57 {
> > > + reg = <0x57>;
> > > + };
> > > +
> > > + /* MCP79402-I/ST RTC */
> > > + rtc@6f {
> > > + compatible = "microchip,mcp7940x";
> > > + reg = <0x6f>;
> > > + interrupt-parent = <&gpio>;
> > > + interrupts = <14 0>; /* GPIO14 - MFP pin */
> > > + };
> > > + };
> > > +
> > > + /* SPI on connector P1 */
> > > + spi0: spi@...0 {
> > > + };
> > > +
> > > + gpio: gpio-controller@...0 {
> > > + #interrupt-cells = <2>;
> > > + interrupt-controller;
> > > + };
> > > +
> > > + /* Connected to SMSC USB2412-DZK 2-Port USB 2.0 Hub Controller */
> > > + usb@...00 {
> > > + phy_type = "ulpi";
> > > + dr_mode = "host";
> > > + };
> > > +
> > > + enet0: ethernet@...00 {
> > > + /* Connected to port 6 of QCA8337N-AL3C switch */
> > > + phy-connection-type = "rgmii-id";
> > > +
> > > + fixed-link {
> > > + speed = <1000>;
> > > + full-duplex;
> > > + };
> > > + };
> > > +
> > > + mdio@...20 {
> > > + /* QCA8337N-AL3C switch with integrated ethernet PHYs for LAN ports */
> > > + switch@10 {
> > > + compatible = "qca,qca8337";
> > > + interrupts = <2 1 0 0>;
> > > + reg = <0x10>;
> > > +
> > > + ports {
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > +
> > > + port@0 {
> > > + reg = <0>;
> > > + label = "cpu1";
> > > + ethernet = <&enet1>;
> > > + phy-mode = "rgmii-id";
> > > +
> > > + fixed-link {
> > > + speed = <1000>;
> > > + full-duplex;
> > > + };
> > > + };
> > > +
> > > + port@1 {
> > > + reg = <1>;
> > > + label = "lan5";
> > > + };
> > > +
> > > + port@2 {
> > > + reg = <2>;
> > > + label = "lan4";
> > > + };
> > > +
> > > + port@3 {
> > > + reg = <3>;
> > > + label = "lan3";
> > > + };
> > > +
> > > + port@4 {
> > > + reg = <4>;
> > > + label = "lan2";
> > > + };
> > > +
> > > + port@5 {
> > > + reg = <5>;
> > > + label = "lan1";
> > > + };
> > > +
> > > + port@6 {
> > > + reg = <6>;
> > > + label = "cpu0";
> > > + ethernet = <&enet0>;
> > > + phy-mode = "rgmii-id";
> > > +
> > > + fixed-link {
> > > + speed = <1000>;
> > > + full-duplex;
> > > + };
> > > + };
> > > + };
> > > + };
> > > +
> > > + /* KSZ9031RNXCA ethernet phy for WAN port */
> > > + phy: ethernet-phy@7 {
> > > + interrupts = <3 1 0 0>;
> > > + reg = <0x7>;
> > > + };
> > > + };
> > > +
> > > + ptp_clock@...00 {
> > > + fsl,tclk-period = <5>;
> > > + fsl,tmr-prsc = <200>;
> > > + fsl,tmr-add = <0xcccccccd>;
> > > + fsl,tmr-fiper1 = <0x3b9ac9fb>;
> > > + fsl,tmr-fiper2 = <0x0001869b>;
> > > + fsl,max-adj = <249999999>;
> > > + };
> > > +
> > > + enet1: ethernet@...00 {
> > > + /* Connected to port 0 of QCA8337N-AL3C switch */
> > > + phy-connection-type = "rgmii-id";
> > > +
> > > + fixed-link {
> > > + speed = <1000>;
> > > + full-duplex;
> > > + };
> > > + };
> > > +
> > > + mdio@...20 {
> > > + status = "disabled";
> > > + };
> > > +
> > > + enet2: ethernet@...00 {
> > > + /* Connected to KSZ9031RNXCA ethernet phy (WAN port) */
> > > + label = "wan";
> > > + phy-handle = <&phy>;
> > > + phy-connection-type = "rgmii-id";
> > > + };
> > > +
> > > + mdio@...20 {
> > > + status = "disabled";
> > > + };
> > > +
> > > + sdhc@...00 {
> > > + bus-width = <4>;
> > > + cd-gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
> > > + };
> > > + };
> > > +
> > > + lbc: localbus@...05000 {
> > > + reg = <0 0xffe05000 0 0x1000>;
> > > +
> > > + ranges = <0x0 0x0 0x0 0xef000000 0x01000000>, /* NOR */
> > > + <0x1 0x0 0x0 0xff800000 0x00040000>, /* NAND */
> > > + <0x3 0x0 0x0 0xffa00000 0x00020000>; /* CPLD */
> > > +
> > > + /* S29GL128P90TFIR10 NOR */
> > > + nor@0,0 {
> > > + compatible = "cfi-flash";
> > > + reg = <0x0 0x0 0x01000000>;
> > > + bank-width = <2>;
> > > + device-width = <1>;
> > > +
> > > + partitions {
> > > + compatible = "fixed-partitions";
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > +
> > > + partition@0 {
> > > + /* 128 kB for Device Tree Blob */
> > > + reg = <0x00000000 0x00020000>;
> > > + label = "dtb";
> > > + };
> > > +
> > > + partition@...00 {
> > > + /* 1.7 MB for Rescue Linux Kernel Image */
> > > + reg = <0x00020000 0x001a0000>;
> > > + label = "rescue-kernel";
> > > + };
> > > +
> > > + partition@...000 {
> > > + /* 1.5 MB for Rescue JFFS2 Root File System */
> > > + reg = <0x001c0000 0x00180000>;
> > > + label = "rescue-rootfs";
> > > + };
> > > +
> > > + partition@...000 {
> > > + /* 11 MB for TAR.XZ Backup with content of NAND Root File System */
> > > + reg = <0x00340000 0x00b00000>;
> > > + label = "backup-rootfs";
> > > + };
> > > +
> > > + partition@...000 {
> > > + /* 768 kB for Certificates JFFS2 File System */
> > > + reg = <0x00e40000 0x000c0000>;
> > > + label = "certificates";
> > > + };
> > > +
> > > + /* free unused space 0x00f00000-0x00f20000 */
> > > +
> > > + partition@...000 {
> > > + /* 128 kB for U-Boot Environment Variables */
> > > + reg = <0x00f20000 0x00020000>;
> > > + label = "u-boot-env";
> > > + };
> > > +
> > > + partition@...000 {
> > > + /* 768 kB for U-Boot Bootloader Image */
> > > + reg = <0x00f40000 0x000c0000>;
> > > + label = "u-boot";
> > > + };
> > > + };
> > > + };
> > > +
> > > + /* MT29F2G08ABAEAWP:E NAND */
> > > + nand@1,0 {
> > > + compatible = "fsl,p2020-fcm-nand", "fsl,elbc-fcm-nand";
> > > + reg = <0x1 0x0 0x00040000>;
> > > + nand-ecc-mode = "soft";
> > > + nand-ecc-algo = "bch";
> > > +
> > > + partitions {
> > > + compatible = "fixed-partitions";
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > +
> > > + partition@0 {
> > > + /* 256 MB for UBI with one volume: UBIFS Root File System */
> > > + reg = <0x00000000 0x10000000>;
> > > + label = "rootfs";
> > > + };
> > > + };
> > > + };
> > > +
> > > + /* LCMXO1200C-3FTN256C FPGA */
> > > + cpld@3,0 {
> > > + /*
> > > + * Turris CPLD firmware which runs on this Lattice FPGA,
> > > + * is extended version of P1021RDB-PC CPLD v4.1 firmware.
> > > + * It is backward compatible with its original version
> > > + * and the only extension is support for Turris LEDs.
> > > + * Turris CPLD firmware is open source and available at:
> > > + * https://gitlab.nic.cz/turris/hw/turris_cpld/-/blob/master/CZ_NIC_Router_CPLD.v
> > > + */
> > > + compatible = "cznic,turris1x-cpld", "fsl,p1021rdb-pc-cpld", "simple-bus";
> > > + reg = <0x3 0x0 0x30>;
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > + ranges = <0x0 0x3 0x0 0x00020000>;
> > > +
> > > + /* MAX6370KA+T watchdog */
> > > + watchdog@2 {
> > > + /*
> > > + * CPLD firmware maps SET0, SET1 and SET2
> > > + * input logic of MAX6370KA+T chip to CPLD
> > > + * memory space at byte offset 0x2. WDI
> > > + * input logic is outside of the CPLD and
> > > + * connected via external GPIO.
> > > + */
> > > + compatible = "maxim,max6370";
> > > + reg = <0x02 0x01>;
> > > + gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
> > > + };
> > > +
> > > + led-controller@13 {
> > > + /*
> > > + * LEDs are controlled by CPLD firmware.
> > > + * All five LAN LEDs share common RGB settings
> > > + * and so it is not possible to set different
> > > + * colors on different LAN ports.
> > > + */
> > > + compatible = "cznic,turris1x-leds";
> > > + reg = <0x13 0x1d>;
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > +
> > > + multi-led@0 {
> > > + reg = <0x0>;
> > > + color = <LED_COLOR_ID_RGB>;
> > > + function = LED_FUNCTION_WAN;
> > > + };
> > > +
> > > + multi-led@1 {
> > > + reg = <0x1>;
> > > + color = <LED_COLOR_ID_RGB>;
> > > + function = LED_FUNCTION_LAN;
> > > + function-enumerator = <5>;
> > > + };
> > > +
> > > + multi-led@2 {
> > > + reg = <0x2>;
> > > + color = <LED_COLOR_ID_RGB>;
> > > + function = LED_FUNCTION_LAN;
> > > + function-enumerator = <4>;
> > > + };
> > > +
> > > + multi-led@3 {
> > > + reg = <0x3>;
> > > + color = <LED_COLOR_ID_RGB>;
> > > + function = LED_FUNCTION_LAN;
> > > + function-enumerator = <3>;
> > > + };
> > > +
> > > + multi-led@4 {
> > > + reg = <0x4>;
> > > + color = <LED_COLOR_ID_RGB>;
> > > + function = LED_FUNCTION_LAN;
> > > + function-enumerator = <2>;
> > > + };
> > > +
> > > + multi-led@5 {
> > > + reg = <0x5>;
> > > + color = <LED_COLOR_ID_RGB>;
> > > + function = LED_FUNCTION_LAN;
> > > + function-enumerator = <1>;
> > > + };
> > > +
> > > + multi-led@6 {
> > > + reg = <0x6>;
> > > + color = <LED_COLOR_ID_RGB>;
> > > + function = LED_FUNCTION_WLAN;
> > > + };
> > > +
> > > + multi-led@7 {
> > > + reg = <0x7>;
> > > + color = <LED_COLOR_ID_RGB>;
> > > + function = LED_FUNCTION_POWER;
> > > + };
> > > + };
> > > + };
> > > + };
> > > +
> > > + pci2: pcie@...08000 {
> > > + /*
> > > + * PCIe bus for on-board TUSB7340RKM USB 3.0 xHCI controller.
> > > + * This xHCI controller is available only on Turris 1.1 boards.
> > > + * Turris 1.0 boards have nothing connected to this PCIe bus,
> > > + * so system would see only PCIe Root Port of this PCIe Root
> > > + * Complex. TUSB7340RKM xHCI controller has four SuperSpeed
> > > + * channels. Channel 0 is connected to the front USB 3.0 port,
> > > + * channel 1 (but only USB 2.0 subset) to USB 2.0 pins on mPCIe
> > > + * slot 1 (CN5), channels 2 and 3 to connector P600.
> > > + *
> > > + * P2020 PCIe Root Port uses 1MB of PCIe MEM and xHCI controller
> > > + * uses 64kB + 8kB of PCIe MEM. No PCIe IO is used or required.
> > > + * So allocate 2MB of PCIe MEM for this PCIe bus.
> > > + */
> > > + reg = <0 0xffe08000 0 0x1000>;
> > > + ranges = <0x02000000 0x0 0xc0000000 0 0xc0000000 0x0 0x00200000>, /* MEM */
> > > + <0x01000000 0x0 0x00000000 0 0xffc20000 0x0 0x00010000>; /* IO */
> > > +
> > > + pcie@0 {
> > > + ranges;
> > > + };
> > > + };
> > > +
> > > + pci1: pcie@...09000 {
> > > + /* PCIe bus on mPCIe slot 2 (CN6) for expansion mPCIe card */
> > > + reg = <0 0xffe09000 0 0x1000>;
> > > + ranges = <0x02000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000>, /* MEM */
> > > + <0x01000000 0x0 0x00000000 0 0xffc10000 0x0 0x00010000>; /* IO */
> > > +
> > > + pcie@0 {
> > > + ranges;
> > > + };
> > > + };
> > > +
> > > + pci0: pcie@...0a000 {
> > > + /*
> > > + * PCIe bus on mPCIe slot 1 (CN5) for expansion mPCIe card.
> > > + * Turris 1.1 boards have in this mPCIe slot additional USB 2.0
> > > + * pins via channel 1 of TUSB7340RKM xHCI controller and also
> > > + * additional SIM card slot, both for USB-based WWAN cards.
> > > + */
> > > + reg = <0 0xffe0a000 0 0x1000>;
> > > + ranges = <0x02000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000>, /* MEM */
> > > + <0x01000000 0x0 0x00000000 0 0xffc00000 0x0 0x00010000>; /* IO */
> > > +
> > > + pcie@0 {
> > > + ranges;
> > > + };
> > > + };
> > > +};
> > > +
> > > +/include/ "fsl/p2020si-post.dtsi"
> > > --
> > > 2.20.1
> > >
Powered by blists - more mailing lists