Message-ID: <YxjhhzTylUUwjCVm@pendragon.ideasonboard.com>
Date:   Wed, 7 Sep 2022 21:23:03 +0300
From:   Laurent Pinchart <laurent.pinchart@...asonboard.com>
To:     Paul Elder <paul.elder@...asonboard.com>
Cc:     Rui Miguel Silva <rmfrfs@...il.com>,
        Steve Longerbeam <slongerbeam@...il.com>,
        linux-media@...r.kernel.org,
        Philipp Zabel <p.zabel@...gutronix.de>,
        Mauro Carvalho Chehab <mchehab@...nel.org>,
        Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
        Shawn Guo <shawnguo@...nel.org>,
        Sascha Hauer <s.hauer@...gutronix.de>,
        Pengutronix Kernel Team <kernel@...gutronix.de>,
        Fabio Estevam <festevam@...il.com>,
        NXP Linux Team <linux-imx@....com>,
        linux-staging@...ts.linux.dev,
        linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v2] media: imx7-media-csi: Add support for fast-tracking
 queued buffers

Hi Paul,

On Wed, Sep 07, 2022 at 09:18:58PM +0300, Laurent Pinchart wrote:
> On Wed, Sep 07, 2022 at 08:47:37PM +0900, Paul Elder wrote:
> > The CSI hardware compatible with this driver handles buffers using a
> > ping-pong mechanism with two sets of destination addresses. Normally,
> > when an interrupt comes in to signal the completion of one buffer, say
> > FB0, it assigns the next buffer in the queue to the next FB0, and the
> > hardware starts to capture into FB1 in the meantime.
> 
> Could you replace FB0 and FB1 with FB1 and FB2 respectively, to match
> the naming of the registers ?
> 
> > In a buffer underrun situation, in the above example without loss of
> > generality, if a new buffer is queued before the interrupt for FB0 comes
> > in, we can program the buffer into FB1 (which is programmed with a dummy
> > buffer, as there is a buffer underrun).
> > 
> > This of course races with the interrupt that signals FB0 completion, as
> > once that interrupt comes in, we are no longer guaranteed that the
> > programming of FB1 was in time and must assume it was too late. This
> > race is resolved partly by locking the programming of FB1. If it came
> > after the interrupt for FB0, then the variable that is used to determine
> > which FB to program would have been swapped by the interrupt handler.
> > 
> > This alone isn't sufficient, however, because the interrupt could still
> > be generated (thus the hardware starts capturing into the other fb)
> > while the fast-tracking routine has the irq lock. Thus, after
> > programming the fb register to fast-track the buffer, the isr also must
> > be checked to confirm that an interrupt didn't come in the meantime. If
> > it has, we must assume that programming the register for the
> > fast-tracked buffer was not in time, and queue the buffer normally.
> > 
> > Signed-off-by: Paul Elder <paul.elder@...asonboard.com>
> > Acked-by: Rui Miguel Silva <rmfrfs@...il.com>
> > 
> > ---
> > Changes in v2:
> > - fix the potential race condition where the interrupt comes in while
> >   the fast tracking routine has the irqlock
> > - change return value from int to bool
> > ---
> >  drivers/staging/media/imx/imx7-media-csi.c | 63 ++++++++++++++++++++++
> >  1 file changed, 63 insertions(+)
> > 
> > diff --git a/drivers/staging/media/imx/imx7-media-csi.c b/drivers/staging/media/imx/imx7-media-csi.c
> > index a0553c24cce4..0ebef44a7627 100644
> > --- a/drivers/staging/media/imx/imx7-media-csi.c
> > +++ b/drivers/staging/media/imx/imx7-media-csi.c
> > @@ -1296,12 +1296,75 @@ static int imx7_csi_video_buf_prepare(struct vb2_buffer *vb)
> >  	return 0;
> >  }
> >  
> > +static bool imx7_csi_fast_track_buffer(struct imx7_csi *csi,
> > +				       struct imx7_csi_vb2_buffer *buf)
> > +{
> > +	unsigned long flags;
> > +	dma_addr_t phys;
> > +	int buf_num;
> > +	u32 isr;
> > +
> > +	if (!csi->is_streaming)
> > +		return false;
> > +
> > +	phys = vb2_dma_contig_plane_dma_addr(&buf->vbuf.vb2_buf, 0);
> > +
> > +	/*
> > +	 * buf_num holds the fb id of the most recently (*not* the next
> > +	 * anticipated) triggered interrupt. Without loss of generality, if
> > +	 * buf_num is 0 and we get to this section before the irq for fb2, the
> 
> s/fb2/FB2/ to match hardware registers and the commit message ?
> 
> > +	 * buffer that we are fast-tracking into fb1 should be programmed in
> > +	 * time to be captured into. If the irq for fb2 already happened, then
> > +	 * buf_num would be 1, and we would fast-track the buffer into fb2
> > +	 * instead. This guarantees that we won't try to fast-track into fb1
> > +	 * and race against the start-of-capture into fb1.
> > +	 *
> > +	 * We only fast-track the buffer if the currently programmed buffer is
> > +	 * a dummy buffer. We can check the active_vb2_buf instead as it is
> > +	 * always modified along with programming the fb[1,2] registers via the
> > +	 * lock (besides setup and cleanup).
> > +	 */
> 
> I think this needs to be updated, it still indicates we handle the race
> just by checking buf_num. How about the following ?
> 
> 	/*
> 	 * buf_num holds the framebuffer ID of the most recently (*not* the next
> 	 * anticipated) triggered interrupt. Without loss of generality, if
> 	 * buf_num is 0, the hardware is capturing to FB2. If FB1 has been
> 	 * programmed with a dummy buffer (as indicated by active_vb2_buf[0]
> 	 * being NULL), then we can fast-track the new buffer by programming its
> 	 * address in FB1 before the hardware completes FB2, instead of adding
> 	 * it to the buffer queue and incurring a delay of one additional frame.
> 	 *
> 	 * The irqlock prevents races with the interrupt handler that queues the
> 	 * next buffer and updates buf_num, but we can still race with the
> 	 * hardware if we program the buffer in FB1 just after the hardware
> 	 * completes FB2 and switches to FB1 and before we notice the buf_num
> 	 * change. The fast-tracked buffer would then be ignored by the hardware
> 	 * while the driver would think it has successfully been processed.
> 	 *
> 	 * To avoid this problem, if we can't avoid the race, we can detect that
> 	 * we have lost it by checking, after programming the buffer in FB1, if
> 	 * the interrupt flag indicated completion of FB2 has been raised. If
> 	 * that is not the case, fast-tracking succeeded, and we can update
> 	 * active_vb2_buf[0]. Otherwise, we may or may not have lost the race
> 	 * (as the interrupt flag may have been raised just after programming
> 	 * FB1 and before we read the interrupt status register), and we need to
> 	 * assume the worst case of a race loss and queue the buffer through the
> 	 * slow path.
> 	 */
> 
> Reviewed-by: Laurent Pinchart <laurent.pinchart@...asonboard.com>
> 
> If you're fine with these changes there's no need to submit a v3, I'll
> update the comment and the commit message locally.
> 
> > +
> > +	spin_lock_irqsave(&csi->irqlock, flags);
> > +
> > +	buf_num = csi->buf_num;
> > +	if (csi->active_vb2_buf[buf_num]) {
> > +		spin_unlock_irqrestore(&csi->irqlock, flags);
> > +		return false;
> > +	}
> > +
> > +	imx7_csi_update_buf(csi, phys, buf_num);
> > +
> > +	isr = imx7_csi_reg_read(csi, CSI_CSISR);
> > +	/*
> > +	 * The interrupt for the /other/ fb just came (the isr hasn't run yet
> > +	 * though, because we have the lock here); we can't be sure we've
> > +	 * programmed buf_num fb in time, so queue the buffer to the buffer
> > +	 * queue normally. No need to undo writing the fb register, since we
> > +	 * won't return it as active_vb2_buf is NULL, so it's okay to
> > +	 * potentially write it to both fb1 and fb2; only the one where it was
> > +	 * queued normally will be returned.
> > +	 */

Also, if you state that the interrupt just came, I'd move the comment to
within the if () { ... }.

> > +	if (isr & (buf_num ? BIT_DMA_TSF_DONE_FB1 : BIT_DMA_TSF_DONE_FB2)) {
> > +		spin_unlock_irqrestore(&csi->irqlock, flags);
> > +		return false;
> > +	}
> > +
> > +	csi->active_vb2_buf[buf_num] = buf;
> > +
> > +	spin_unlock_irqrestore(&csi->irqlock, flags);
> > +	return true;
> > +}
> > +
> >  static void imx7_csi_video_buf_queue(struct vb2_buffer *vb)
> >  {
> >  	struct imx7_csi *csi = vb2_get_drv_priv(vb->vb2_queue);
> >  	struct imx7_csi_vb2_buffer *buf = to_imx7_csi_vb2_buffer(vb);
> >  	unsigned long flags;
> >  
> > +	if (imx7_csi_fast_track_buffer(csi, buf))
> > +		return;
> > +
> >  	spin_lock_irqsave(&csi->q_lock, flags);
> >  
> >  	list_add_tail(&buf->list, &csi->ready_q);

-- 
Regards,

Laurent Pinchart

Powered by blists - more mailing lists