| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Thu, 8 Sep 2022 06:44:56 +0000
From: <Claudiu.Beznea@...rochip.com>
To: <Conor.Dooley@...rochip.com>, <mturquette@...libre.com>,
<sboyd@...nel.org>, <robh+dt@...nel.org>,
<krzysztof.kozlowski+dt@...aro.org>, <palmer@...belt.com>,
<Daire.McNamara@...rochip.com>
CC: <paul.walmsley@...ive.com>, <aou@...s.berkeley.edu>,
<linux-clk@...r.kernel.org>, <devicetree@...r.kernel.org>,
<linux-kernel@...r.kernel.org>, <linux-riscv@...ts.infradead.org>,
<p.zabel@...gutronix.de>
Subject: Re: [PATCH v4 04/13] reset: add polarfire soc reset support
On 30.08.2022 15:52, Conor Dooley wrote:
> Add support for the resets on Microchip's PolarFire SoC (MPFS).
> Reset control is a single register, wedged in between registers for
> clock control. To fit with existed DT etc, the reset controller is
> created using the aux device framework & set up in the clock driver.
>
> Reviewed-by: Philipp Zabel <p.zabel@...gutronix.de>
> Acked-by: Philipp Zabel <p.zabel@...gutronix.de>
> Reviewed-by: Daire McNamara <daire.mcnamara@...rochip.com>
> Signed-off-by: Conor Dooley <conor.dooley@...rochip.com>
> ---
> drivers/reset/Kconfig | 7 ++
> drivers/reset/Makefile | 2 +-
> drivers/reset/reset-mpfs.c | 157 +++++++++++++++++++++++++++++++++++++
> 3 files changed, 165 insertions(+), 1 deletion(-)
> create mode 100644 drivers/reset/reset-mpfs.c
>
> diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
> index 806773e88832..85f7abde3766 100644
> --- a/drivers/reset/Kconfig
> +++ b/drivers/reset/Kconfig
> @@ -152,6 +152,13 @@ config RESET_PISTACHIO
> help
> This enables the reset driver for ImgTec Pistachio SoCs.
>
> +config RESET_POLARFIRE_SOC
> + bool "Microchip PolarFire SoC (MPFS) Reset Driver"
> + depends on AUXILIARY_BUS && MCHP_CLK_MPFS
> + default MCHP_CLK_MPFS
> + help
> + This driver supports peripheral reset for the Microchip PolarFire SoC
> +
> config RESET_QCOM_AOSS
> tristate "Qcom AOSS Reset Driver"
> depends on ARCH_QCOM || COMPILE_TEST
> diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
> index cd5cf8e7c6a7..3e7e5fd633a8 100644
> --- a/drivers/reset/Makefile
> +++ b/drivers/reset/Makefile
> @@ -22,6 +22,7 @@ obj-$(CONFIG_RESET_MESON_AUDIO_ARB) += reset-meson-audio-arb.o
> obj-$(CONFIG_RESET_NPCM) += reset-npcm.o
> obj-$(CONFIG_RESET_OXNAS) += reset-oxnas.o
> obj-$(CONFIG_RESET_PISTACHIO) += reset-pistachio.o
> +obj-$(CONFIG_RESET_POLARFIRE_SOC) += reset-mpfs.o
> obj-$(CONFIG_RESET_QCOM_AOSS) += reset-qcom-aoss.o
> obj-$(CONFIG_RESET_QCOM_PDC) += reset-qcom-pdc.o
> obj-$(CONFIG_RESET_RASPBERRYPI) += reset-raspberrypi.o
> @@ -40,4 +41,3 @@ obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o
> obj-$(CONFIG_RESET_UNIPHIER_GLUE) += reset-uniphier-glue.o
> obj-$(CONFIG_RESET_ZYNQ) += reset-zynq.o
> obj-$(CONFIG_ARCH_ZYNQMP) += reset-zynqmp.o
> -
> diff --git a/drivers/reset/reset-mpfs.c b/drivers/reset/reset-mpfs.c
> new file mode 100644
> index 000000000000..1580d1b68d61
> --- /dev/null
> +++ b/drivers/reset/reset-mpfs.c
> @@ -0,0 +1,157 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * PolarFire SoC (MPFS) Peripheral Clock Reset Controller
> + *
> + * Author: Conor Dooley <conor.dooley@...rochip.com>
> + * Copyright (c) 2022 Microchip Technology Inc. and its subsidiaries.
> + *
> + */
> +#include <linux/auxiliary_bus.h>
> +#include <linux/delay.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/reset-controller.h>
> +#include <dt-bindings/clock/microchip,mpfs-clock.h>
> +#include <soc/microchip/mpfs.h>
> +
> +/*
> + * The ENVM reset is the lowest bit in the register & I am using the CLK_FOO
> + * defines in the dt to make things easier to configure - so this is accounting
> + * for the offset of 3 there.
> + */
> +#define MPFS_PERIPH_OFFSET CLK_ENVM
> +#define MPFS_NUM_RESETS 30u
> +#define MPFS_SLEEP_MIN_US 100
> +#define MPFS_SLEEP_MAX_US 200
> +
> +/* block concurrent access to the soft reset register */
> +static DEFINE_SPINLOCK(mpfs_reset_lock);
> +
> +/*
> + * Peripheral clock resets
> + */
> +
> +static int mpfs_assert(struct reset_controller_dev *rcdev, unsigned long id)
> +{
> + unsigned long flags;
> + u32 reg;
> +
> + spin_lock_irqsave(&mpfs_reset_lock, flags);
> +
> + reg = mpfs_reset_read(rcdev->dev);
> + reg |= BIT(id);
> + mpfs_reset_write(rcdev->dev, reg);
> +
> + spin_unlock_irqrestore(&mpfs_reset_lock, flags);
> +
> + return 0;
> +}
> +
> +static int mpfs_deassert(struct reset_controller_dev *rcdev, unsigned long id)
> +{
> + unsigned long flags;
> + u32 reg, val;
Using either reg or val in this function should be enough.
Other than this:
Reviewed-by: Claudiu Beznea <claudiu.beznea@...rochip.com>
> +
> + spin_lock_irqsave(&mpfs_reset_lock, flags);
> +
> + reg = mpfs_reset_read(rcdev->dev);
> + val = reg & ~BIT(id);
> + mpfs_reset_write(rcdev->dev, val);
> +
> + spin_unlock_irqrestore(&mpfs_reset_lock, flags);
> +
> + return 0;
> +}
> +
> +static int mpfs_status(struct reset_controller_dev *rcdev, unsigned long id)
> +{
> + u32 reg = mpfs_reset_read(rcdev->dev);
> +
> + /*
> + * It is safe to return here as MPFS_NUM_RESETS makes sure the sign bit
> + * is never hit.
> + */
> + return (reg & BIT(id));
> +}
> +
> +static int mpfs_reset(struct reset_controller_dev *rcdev, unsigned long id)
> +{
> + mpfs_assert(rcdev, id);
> +
> + usleep_range(MPFS_SLEEP_MIN_US, MPFS_SLEEP_MAX_US);
> +
> + mpfs_deassert(rcdev, id);
> +
> + return 0;
> +}
> +
> +static const struct reset_control_ops mpfs_reset_ops = {
> + .reset = mpfs_reset,
> + .assert = mpfs_assert,
> + .deassert = mpfs_deassert,
> + .status = mpfs_status,
> +};
> +
> +static int mpfs_reset_xlate(struct reset_controller_dev *rcdev,
> + const struct of_phandle_args *reset_spec)
> +{
> + unsigned int index = reset_spec->args[0];
> +
> + /*
> + * CLK_RESERVED does not map to a clock, but it does map to a reset,
> + * so it has to be accounted for here. It is the reset for the fabric,
> + * so if this reset gets called - do not reset it.
> + */
> + if (index == CLK_RESERVED) {
> + dev_err(rcdev->dev, "Resetting the fabric is not supported\n");
> + return -EINVAL;
> + }
> +
> + if (index < MPFS_PERIPH_OFFSET || index >= (MPFS_PERIPH_OFFSET + rcdev->nr_resets)) {
> + dev_err(rcdev->dev, "Invalid reset index %u\n", index);
> + return -EINVAL;
> + }
> +
> + return index - MPFS_PERIPH_OFFSET;
> +}
> +
> +static int mpfs_reset_probe(struct auxiliary_device *adev,
> + const struct auxiliary_device_id *id)
> +{
> + struct device *dev = &adev->dev;
> + struct reset_controller_dev *rcdev;
> +
> + rcdev = devm_kzalloc(dev, sizeof(*rcdev), GFP_KERNEL);
> + if (!rcdev)
> + return -ENOMEM;
> +
> + rcdev->dev = dev;
> + rcdev->dev->parent = dev->parent;
> + rcdev->ops = &mpfs_reset_ops;
> + rcdev->of_node = dev->parent->of_node;
> + rcdev->of_reset_n_cells = 1;
> + rcdev->of_xlate = mpfs_reset_xlate;
> + rcdev->nr_resets = MPFS_NUM_RESETS;
> +
> + return devm_reset_controller_register(dev, rcdev);
> +}
> +
> +static const struct auxiliary_device_id mpfs_reset_ids[] = {
> + {
> + .name = "clk_mpfs.reset-mpfs",
> + },
> + { }
> +};
> +MODULE_DEVICE_TABLE(auxiliary, mpfs_reset_ids);
> +
> +static struct auxiliary_driver mpfs_reset_driver = {
> + .probe = mpfs_reset_probe,
> + .id_table = mpfs_reset_ids,
> +};
> +
> +module_auxiliary_driver(mpfs_reset_driver);
> +
> +MODULE_DESCRIPTION("Microchip PolarFire SoC Reset Driver");
> +MODULE_AUTHOR("Conor Dooley <conor.dooley@...rochip.com>");
> +MODULE_LICENSE("GPL");
> +MODULE_IMPORT_NS(MCHP_CLK_MPFS);
Powered by blists - more mailing lists