| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <2894e7db-78b1-59ee-ad5f-e45c8597e9cf@microchip.com>
Date: Wed, 21 Sep 2022 06:27:10 +0000
From: <Claudiu.Beznea@...rochip.com>
To: <Sergiu.Moga@...rochip.com>, <lee@...nel.org>,
<robh+dt@...nel.org>, <krzysztof.kozlowski+dt@...aro.org>,
<Nicolas.Ferre@...rochip.com>, <alexandre.belloni@...tlin.com>,
<radu_nicolae.pirea@....ro>, <richard.genoud@...il.com>,
<gregkh@...uxfoundation.org>, <jirislaby@...nel.org>,
<Kavyasree.Kotagiri@...rochip.com>
CC: <devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>, <linux-spi@...r.kernel.org>,
<linux-serial@...r.kernel.org>
Subject: Re: [PATCH v4 9/9] tty: serial: atmel: Make the driver aware of the
existence of GCLK
On 21.09.2022 08:51, Claudiu Beznea - M18063 wrote:
> On 19.09.2022 18:08, Sergiu Moga wrote:
>> Previously, the atmel serial driver did not take into account the
>> possibility of using the more customizable generic clock as its
>> baudrate generator. Unless there is a Fractional Part available to
>> increase accuracy, there is a high chance that we may be able to
>> generate a baudrate closer to the desired one by using the GCLK as the
>> clock source. Now, depending on the error rate between
>> the desired baudrate and the actual baudrate, the serial driver will
>> fallback on the generic clock. The generic clock must be provided
>> in the DT node of the serial that may need a more flexible clock source.
>>
>> Signed-off-by: Sergiu Moga <sergiu.moga@...rochip.com>
>
> Reviewed-by: Claudiu Beznea <claudiu.beznea@...rochip.com>
Actually, I'm taking this back at the moment.
>
>
>> ---
>>
>>
>> v1 -> v2:
>> - take into account the different placement of the baudrate clock source
>> into the IP's Mode Register (USART vs UART)
>> - don't check for atmel_port->gclk != NULL
>> - use clk_round_rate instead of clk_set_rate + clk_get_rate
>> - remove clk_disable_unprepare from the end of the probe method
>>
>>
>>
>> v2 -> v3:
>> - add the error rate calculation function as an inline function instead of
>> a macro definition
>> - add `gclk_fail` goto
>> - replace `goto err` with `goto err_clk_disable_unprepare;`
>>
>>
>>
>> v3 -> v4:
>> - Nothing, this was previously [PATCH 14]
>>
>>
>> drivers/tty/serial/atmel_serial.c | 59 ++++++++++++++++++++++++++++++-
>> 1 file changed, 58 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
>> index c983798a4ab2..426f9d4f9a5a 100644
>> --- a/drivers/tty/serial/atmel_serial.c
>> +++ b/drivers/tty/serial/atmel_serial.c
>> @@ -15,6 +15,7 @@
>> #include <linux/init.h>
>> #include <linux/serial.h>
>> #include <linux/clk.h>
>> +#include <linux/clk-provider.h>
>> #include <linux/console.h>
>> #include <linux/sysrq.h>
>> #include <linux/tty_flip.h>
>> @@ -110,6 +111,7 @@ struct atmel_uart_char {
>> struct atmel_uart_port {
>> struct uart_port uart; /* uart */
>> struct clk *clk; /* uart clock */
>> + struct clk *gclk; /* uart generic clock */
>> int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */
>> u32 backup_imr; /* IMR saved during suspend */
>> int break_active; /* break being received */
>> @@ -229,6 +231,11 @@ static inline int atmel_uart_is_half_duplex(struct uart_port *port)
>> (port->iso7816.flags & SER_ISO7816_ENABLED);
>> }
>>
>> +static inline int atmel_error_rate(int desired_value, int actual_value)
>> +{
>> + return 100 - (desired_value * 100) / actual_value;
>> +}
>> +
>> #ifdef CONFIG_SERIAL_ATMEL_PDC
>> static bool atmel_use_pdc_rx(struct uart_port *port)
>> {
>> @@ -2117,6 +2124,8 @@ static void atmel_serial_pm(struct uart_port *port, unsigned int state,
>> * This is called on uart_close() or a suspend event.
>> */
>> clk_disable_unprepare(atmel_port->clk);
>> + if (__clk_is_enabled(atmel_port->gclk))
>> + clk_disable_unprepare(atmel_port->gclk);
>> break;
>> default:
>> dev_err(port->dev, "atmel_serial: unknown pm %d\n", state);
>> @@ -2132,7 +2141,9 @@ static void atmel_set_termios(struct uart_port *port,
>> {
>> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>> unsigned long flags;
>> - unsigned int old_mode, mode, imr, quot, baud, div, cd, fp = 0;
>> + unsigned int old_mode, mode, imr, quot, div, cd, fp = 0;
>> + unsigned int baud, actual_baud, gclk_rate;
>> + int ret;
>>
>> /* save the current mode register */
>> mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR);
>> @@ -2302,6 +2313,46 @@ static void atmel_set_termios(struct uart_port *port,
>> cd = min_t(unsigned int, cd, ATMEL_US_CD);
>> }
>>
>> + /*
>> + * If there is no Fractional Part, there is a high chance that
>> + * we may be able to generate a baudrate closer to the desired one
>> + * if we use the GCLK as the clock source driving the baudrate
>> + * generator.
>> + */
>> + if (!atmel_port->has_frac_baudrate) {
>> + if (__clk_is_enabled(atmel_port->gclk))
>> + clk_disable_unprepare(atmel_port->gclk);
>> + gclk_rate = clk_round_rate(atmel_port->gclk, 16 * baud);
>> + actual_baud = clk_get_rate(atmel_port->clk) / (16 * cd);
>> + if (gclk_rate && abs(atmel_error_rate(baud, actual_baud)) >
>> + abs(atmel_error_rate(baud, gclk_rate / 16))) {
If this condition fails and you previously used GCLK for clock generation
you should remove bits ATMEL_US_USCLKS or ATMEL_UA_BRSRCCK from mode
variable, to avoid configuring MR with GCLK support and clock not being
properly setup.
>> + clk_set_rate(atmel_port->gclk, 16 * baud);
>> + ret = clk_prepare_enable(atmel_port->gclk);
>> + if (ret)
>> + goto gclk_fail;
>> +
>> + if (atmel_port->is_usart) {
>> + mode &= ~ATMEL_US_USCLKS;
>> + mode |= ATMEL_US_USCLKS_GCLK;
>> + } else {
>> + mode &= ~ATMEL_UA_BRSRCCK;
>> + mode |= ATMEL_UA_BRSRCCK_GCLK;
>> + }
>> +
>> + /*
>> + * Set the Clock Divisor for GCLK to 1.
>> + * Since we were able to generate the smallest
>> + * multiple of the desired baudrate times 16,
>> + * then we surely can generate a bigger multiple
>> + * with the exact error rate for an equally increased
>> + * CD. Thus no need to take into account
>> + * a higher value for CD.
>> + */
>> + cd = 1;
>> + }
>> + }
>> +
>> +gclk_fail:
>> quot = cd | fp << ATMEL_US_FP_OFFSET;
>>
>> if (!(port->iso7816.flags & SER_ISO7816_ENABLED))
>> @@ -2897,6 +2948,12 @@ static int atmel_serial_probe(struct platform_device *pdev)
>> if (ret)
>> goto err;
>>
>> + atmel_port->gclk = devm_clk_get_optional(&pdev->dev, "gclk");
>> + if (IS_ERR(atmel_port->gclk)) {
>> + ret = PTR_ERR(atmel_port->gclk);
>> + goto err_clk_disable_unprepare;
>> + }
>> +
>> ret = atmel_init_port(atmel_port, pdev);
>> if (ret)
>> goto err_clk_disable_unprepare;
>
Powered by blists - more mailing lists