| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20220930200529.331223-3-krzysztof.kozlowski@linaro.org>
Date: Fri, 30 Sep 2022 22:05:29 +0200
From: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
To: Andy Gross <agross@...nel.org>,
Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konrad.dybcio@...ainline.org>,
Linus Walleij <linus.walleij@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
linux-arm-msm@...r.kernel.org, linux-gpio@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
Subject: [PATCH 2/2] dt-bindings: pinctrl: qcom,sdm845: convert to dtschema
Convert Qualcomm SDM845 pin controller bindings to DT schema. Keep
the parsing of pin configuration subnodes consistent with other Qualcomm
schemas (children named with '-state' suffix, their children with
'-pins').
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
---
.../bindings/pinctrl/qcom,sdm845-pinctrl.txt | 176 ------------------
.../bindings/pinctrl/qcom,sdm845-pinctrl.yaml | 158 ++++++++++++++++
2 files changed, 158 insertions(+), 176 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt
create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt
deleted file mode 100644
index 7462e3743c68..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.txt
+++ /dev/null
@@ -1,176 +0,0 @@
-Qualcomm SDM845 TLMM block
-
-This binding describes the Top Level Mode Multiplexer block found in the
-SDM845 platform.
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: must be "qcom,sdm845-pinctrl"
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: the base address and size of the TLMM register space.
-
-- interrupts:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: should specify the TLMM summary IRQ.
-
-- interrupt-controller:
- Usage: required
- Value type: <none>
- Definition: identifies this node as an interrupt controller
-
-- #interrupt-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 2. Specifying the pin number and flags, as defined
- in <dt-bindings/interrupt-controller/irq.h>
-
-- gpio-controller:
- Usage: required
- Value type: <none>
- Definition: identifies this node as a gpio controller
-
-- #gpio-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 2. Specifying the pin number and flags, as defined
- in <dt-bindings/gpio/gpio.h>
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-The pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-
-PIN CONFIGURATION NODES:
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
-
-- pins:
- Usage: required
- Value type: <string-array>
- Definition: List of gpio pins affected by the properties specified in
- this subnode.
-
- Valid pins are:
- gpio0-gpio149
- Supports mux, bias and drive-strength
-
- sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset
- Supports bias and drive-strength
-
-- function:
- Usage: required
- Value type: <string>
- Definition: Specify the alternative function to be configured for the
- specified pins. Functions are only valid for gpio pins.
- Valid values are:
-
- gpio, adsp_ext, agera_pll, atest_char, atest_tsens,
- atest_tsens2, atest_usb1, atest_usb10, atest_usb11,
- atest_usb12, atest_usb13, atest_usb2, atest_usb20,
- atest_usb21, atest_usb22, atest_usb23, audio_ref,
- btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0,
- cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng,
- cri_trng0, cri_trng1, dbg_out, ddr_bist, ddr_pxi0,
- ddr_pxi1, ddr_pxi2, ddr_pxi3, edp_hot, edp_lcd, gcc_gp1,
- gcc_gp2, gcc_gp3, jitter_bist, ldo_en, ldo_update,
- lpass_slimbus, m_voc, mdp_vsync, mdp_vsync0, mdp_vsync1,
- mdp_vsync2, mdp_vsync3, mss_lte, nav_pps, pa_indicator,
- pci_e0, pci_e1, phase_flag, pll_bist, pll_bypassnl,
- pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc, qdss_cti,
- qdss, qlink_enable, qlink_request, qua_mi2s, qup0, qup1,
- qup10, qup11, qup12, qup13, qup14, qup15, qup2, qup3, qup4,
- qup5, qup6, qup7, qup8, qup9, qup_l4, qup_l5, qup_l6,
- qspi_clk, qspi_cs, qspi_data, sd_write, sdc4_clk, sdc4_cmd,
- sdc4_data, sec_mi2s, sp_cmu, spkr_i2s, ter_mi2s, tgu_ch0,
- tgu_ch1, tgu_ch2, tgu_ch3, tsense_pwm1, tsense_pwm2,
- tsif1_clk, tsif1_data, tsif1_en, tsif1_error, tsif1_sync,
- tsif2_clk, tsif2_data, tsif2_en, tsif2_error, tsif2_sync,
- uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk,
- uim2_data, uim2_present, uim2_reset, uim_batt, usb_phy,
- vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0,
- wlan2_adc1,
-
-- bias-disable:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as no pull.
-
-- bias-pull-down:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as pull down.
-
-- bias-pull-up:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as pull up.
-
-- output-high:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- high.
- Not valid for sdc pins.
-
-- output-low:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- low.
- Not valid for sdc pins.
-
-- drive-strength:
- Usage: optional
- Value type: <u32>
- Definition: Selects the drive strength for the specified pins, in mA.
- Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
-
-Example:
-
- tlmm: pinctrl@...0000 {
- compatible = "qcom,sdm845-pinctrl";
- reg = <0x03400000 0xc00000>;
- interrupts = <GIC_SPI 208 0>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- qup9_active: qup9-active {
- mux {
- pins = "gpio4", "gpio5";
- function = "qup9";
- };
-
- config {
- pins = "gpio4", "gpio5";
- drive-strength = <2>;
- bias-disable;
- };
- };
- };
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.yaml
new file mode 100644
index 000000000000..da0ef5698f3e
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.yaml
@@ -0,0 +1,158 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,sdm845-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SDM845 TLMM pin controller
+
+maintainers:
+ - Bjorn Andersson <andersson@...nel.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>
+
+description:
+ Top Level Mode Multiplexer pin controller node in Qualcomm SDM845 SoC.
+
+allOf:
+ - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+properties:
+ compatible:
+ const: qcom,sdm845-pinctrl
+
+ reg:
+ maxItems: 1
+
+ interrupts: true
+ interrupt-controller: true
+ "#interrupt-cells": true
+ gpio-controller: true
+
+ gpio-reserved-ranges:
+ minItems: 1
+ maxItems: 75
+
+ gpio-line-names:
+ maxItems: 150
+
+ "#gpio-cells": true
+ gpio-ranges: true
+ wakeup-parent: true
+
+patternProperties:
+ "-state$":
+ oneOf:
+ - $ref: "#/$defs/qcom-sdm845-tlmm-state"
+ - patternProperties:
+ "-pins$":
+ $ref: "#/$defs/qcom-sdm845-tlmm-state"
+ additionalProperties: false
+
+$defs:
+ qcom-sdm845-tlmm-state:
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+
+ properties:
+ pins:
+ description:
+ List of gpio pins affected by the properties specified in this
+ subnode.
+ items:
+ oneOf:
+ - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-4][0-9])$"
+ - enum: [ ufs_reset, sdc2_clk, sdc2_cmd, sdc2_data ]
+ minItems: 1
+ maxItems: 36
+
+ function:
+ description:
+ Specify the alternative function to be configured for the specified
+ pins.
+ enum: [ adsp_ext, agera_pll, atest_char, atest_tsens, atest_tsens2,
+ atest_usb1, atest_usb10, atest_usb11, atest_usb12, atest_usb13,
+ atest_usb2, atest_usb20, atest_usb21, atest_usb22, atest_usb23,
+ audio_ref, btfm_slimbus, cam_mclk, cci_async, cci_i2c,
+ cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4,
+ cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist, ddr_pxi0,
+ ddr_pxi1, ddr_pxi2, ddr_pxi3, edp_hot, edp_lcd, gcc_gp1,
+ gcc_gp2, gcc_gp3, gpio, jitter_bist, ldo_en, ldo_update,
+ lpass_slimbus, mdp_vsync, mdp_vsync0, mdp_vsync1, mdp_vsync2,
+ mdp_vsync3, mss_lte, m_voc, nav_pps, pa_indicator, pci_e0,
+ pci_e1, phase_flag, pll_bist, pll_bypassnl, pll_reset,
+ pri_mi2s, pri_mi2s_ws, prng_rosc, qdss, qdss_cti, qlink_enable,
+ qlink_request, qspi_clk, qspi_cs, qspi_data, qua_mi2s, qup0,
+ qup1, qup10, qup11, qup12, qup13, qup14, qup15, qup2, qup3,
+ qup4, qup5, qup6, qup7, qup8, qup9, qup_l4, qup_l5, qup_l6,
+ sdc4_clk, sdc4_cmd, sdc4_data, sd_write, sec_mi2s, sp_cmu,
+ spkr_i2s, ter_mi2s, tgu_ch0, tgu_ch1, tgu_ch2, tgu_ch3,
+ tsense_pwm1, tsense_pwm2, tsif1_clk, tsif1_data, tsif1_en,
+ tsif1_error, tsif1_sync, tsif2_clk, tsif2_data, tsif2_en,
+ tsif2_error, tsif2_sync, uim1_clk, uim1_data, uim1_present,
+ uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset,
+ uim_batt, usb_phy, vfr_1, vsense_trigger, wlan1_adc0,
+ wlan1_adc1, wlan2_adc0, wlan2_adc1]
+
+ bias-disable: true
+ bias-pull-down: true
+ bias-pull-up: true
+ drive-strength: true
+ input-enable: true
+ output-high: true
+ output-low: true
+
+ required:
+ - pins
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ pinctrl@...0000 {
+ compatible = "qcom,sdm845-pinctrl";
+ reg = <0x03400000 0xc00000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 151>;
+ wakeup-parent = <&pdc_intc>;
+
+ cci0-default-state {
+ pins = "gpio17", "gpio18";
+ function = "cci_i2c";
+
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ cam0-default-state {
+ rst-pins {
+ pins = "gpio9";
+ function = "gpio";
+
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ mclk0-pins {
+ pins = "gpio13";
+ function = "cam_mclk";
+
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+ };
--
2.34.1
Powered by blists - more mailing lists