Message-ID: <519312b6-f28c-7482-21c1-d9628f0295cb@molgen.mpg.de>
Date:   Tue, 14 Mar 2023 12:46:50 +0100
From:   Paul Menzel <pmenzel@...gen.mpg.de>
To:     Jim Liu <jim.t90615@...il.com>
Cc:     JJLIU0@...oton.com, KWLIU@...oton.com, linus.walleij@...aro.org,
        brgl@...ev.pl, robh+dt@...nel.org,
        krzysztof.kozlowski+dt@...aro.org, linux-gpio@...r.kernel.org,
        openbmc@...ts.ozlabs.org, linux-kernel@...r.kernel.org,
        devicetree@...r.kernel.org
Subject: Re: [PATCH v5 1/3] gpio: nuvoton: Add Nuvoton NPCM sgpio driver

Dear Jim,


Am 14.03.23 um 10:23 schrieb Jim Liu:
> Add Nuvoton BMC NPCM7xx/NPCM8xx sgpio driver support.

This commit message is too terse for adding over 650 new lines. Please 
elaborate, and mention the datasheet name and revision, and how you 
tested this.

Also, Why is a new driver needed?

> Signed-off-by: Jim Liu <jim.t90615@...il.com>

Should your company address be used instead?

> ---
> Changes for v5:
>     - remove printk
>     - add descriptive for to_bank
>     - using "GPL" instead of "GPL v2"
> Changes for v4:
>     - followed reviewer suggestion to modify npcm_sgpio_dir_in
>     - blank line in npcm_sgpio_dir_out
>     - use int type for dir in npcm_sgpio_get
> 
> Changes for v3:
>     - remove return in bank_reg function
> Changes for v2:
>     - add prefix
>     - write the enum values in all capitals
>     - remove _init in npcm_sgpio_probe
> ---
>   drivers/gpio/Kconfig           |   8 +
>   drivers/gpio/Makefile          |   1 +
>   drivers/gpio/gpio-npcm-sgpio.c | 648 +++++++++++++++++++++++++++++++++
>   3 files changed, 657 insertions(+)
>   create mode 100644 drivers/gpio/gpio-npcm-sgpio.c
> 
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index 13be729710f2..3296eb23245a 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -460,6 +460,14 @@ config GPIO_MXS
>   	select GPIO_GENERIC
>   	select GENERIC_IRQ_CHIP
>   
> +config GPIO_NPCM_SGPIO
> +	bool "Nuvoton SGPIO support"
> +	depends on (ARCH_NPCM || COMPILE_TEST) && OF_GPIO
> +	select GPIO_GENERIC
> +	select GPIOLIB_IRQCHIP
> +	help
> +	  Say Y here to support Nuvoton NPCM7XX/NPCM8XX SGPIO functionality.
> +
>   config GPIO_OCTEON
>   	tristate "Cavium OCTEON GPIO"
>   	depends on CAVIUM_OCTEON_SOC
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index c048ba003367..1cbf21934299 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -110,6 +110,7 @@ obj-$(CONFIG_GPIO_MT7621)		+= gpio-mt7621.o
>   obj-$(CONFIG_GPIO_MVEBU)		+= gpio-mvebu.o
>   obj-$(CONFIG_GPIO_MXC)			+= gpio-mxc.o
>   obj-$(CONFIG_GPIO_MXS)			+= gpio-mxs.o
> +obj-$(CONFIG_GPIO_NPCM_SGPIO)		+= gpio-npcm-sgpio.o
>   obj-$(CONFIG_GPIO_OCTEON)		+= gpio-octeon.o
>   obj-$(CONFIG_GPIO_OMAP)			+= gpio-omap.o
>   obj-$(CONFIG_GPIO_PALMAS)		+= gpio-palmas.o
> diff --git a/drivers/gpio/gpio-npcm-sgpio.c b/drivers/gpio/gpio-npcm-sgpio.c
> new file mode 100644
> index 000000000000..10bab1495a6c
> --- /dev/null
> +++ b/drivers/gpio/gpio-npcm-sgpio.c
> @@ -0,0 +1,648 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Nuvoton NPCM Serial GPIO Driver
> + *
> + * Copyright (C) 2021 Nuvoton Technologies
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/clk.h>
> +#include <linux/gpio/driver.h>
> +#include <linux/hashtable.h>
> +#include <linux/init.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/spinlock.h>
> +#include <linux/string.h>
> +
> +#define MAX_NR_HW_SGPIO			64
> +
> +#define  NPCM_IOXCFG1				0x2A
> +#define  NPCM_IOXCFG1_SFT_CLK		GENMASK(3, 0)
> +#define  NPCM_IOXCFG1_SCLK_POL		BIT(4)
> +#define  NPCM_IOXCFG1_LDSH_POL		BIT(5)
> +
> +#define  NPCM_IOXCTS 0x28
> +#define  NPCM_IOXCTS_IOXIF_EN BIT(7)
> +#define  NPCM_IOXCTS_RD_MODE GENMASK(2, 1)
> +#define  NPCM_IOXCTS_RD_MODE_PERIODIC BIT(2)
> +#define  NPCM_IOXCTS_RD_MODE_CONTINUOUS GENMASK(2, 1)
> +
> +#define  NPCM_IOXCFG2 0x2B
> +#define  NPCM_IXOEVCFG_MASK 0x3
> +#define  NPCM_IXOEVCFG_BOTH 0x3
> +#define  NPCM_IXOEVCFG_FALLING 0x2
> +#define  NPCM_IXOEVCFG_RISING 0x1
> +
> +#define GPIO_BANK(x)    ((x) / 8)
> +#define GPIO_BIT(x)     ((x) % 8)
> +
> +/*
> + * Select the freqency of shift clock.

frequency

> + * The shift clock is a division of the APB clock.
> + */
> +struct npcm_clk_cfg {
> +	const int *SFT_CLK;
> +	const u8 *CLK_SEL;
> +	const u8 cfg_opt;

Why fix the length of the variables? Can’t standard `unsigned int` be used?

> +};
> +
> +struct npcm_sgpio {
> +	struct gpio_chip chip;
> +	struct clk *pclk;
> +	struct irq_chip intc;
> +	spinlock_t lock; /*protect event config*/
> +	void __iomem *base;
> +	int irq;
> +	u8 nin_sgpio;
> +	u8 nout_sgpio;
> +	u8 in_port;
> +	u8 out_port;
> +	u8 int_type[MAX_NR_HW_SGPIO];
> +};
> +
> +struct npcm_sgpio_bank {
> +	u8 rdata_reg;
> +	u8 wdata_reg;
> +	u8 event_config;
> +	u8 event_status;
> +};
> +
> +enum npcm_sgpio_reg {
> +	READ_DATA,
> +	WRITE_DATA,
> +	EVENT_CFG,
> +	EVENT_STS,
> +};
> +
> +static const struct npcm_sgpio_bank npcm_sgpio_banks[] = {
> +	{
> +		.wdata_reg = 0x00,
> +		.rdata_reg = 0x08,
> +		.event_config = 0x10,
> +		.event_status = 0x20,
> +	},
> +	{
> +		.wdata_reg = 0x01,
> +		.rdata_reg = 0x09,
> +		.event_config = 0x12,
> +		.event_status = 0x21,
> +	},
> +	{
> +		.wdata_reg = 0x02,
> +		.rdata_reg = 0x0a,
> +		.event_config = 0x14,
> +		.event_status = 0x22,
> +	},
> +	{
> +		.wdata_reg = 0x03,
> +		.rdata_reg = 0x0b,
> +		.event_config = 0x16,
> +		.event_status = 0x23,
> +	},
> +	{
> +		.wdata_reg = 0x04,
> +		.rdata_reg = 0x0c,
> +		.event_config = 0x18,
> +		.event_status = 0x24,
> +	},
> +	{
> +		.wdata_reg = 0x05,
> +		.rdata_reg = 0x0d,
> +		.event_config = 0x1a,
> +		.event_status = 0x25,
> +	},
> +	{
> +		.wdata_reg = 0x06,
> +		.rdata_reg = 0x0e,
> +		.event_config = 0x1c,
> +		.event_status = 0x26,
> +	},
> +	{
> +		.wdata_reg = 0x07,
> +		.rdata_reg = 0x0f,
> +		.event_config = 0x1e,
> +		.event_status = 0x27,
> +	},
> +
> +};
> +
> +static void __iomem *bank_reg(struct npcm_sgpio *gpio,
> +			      const struct npcm_sgpio_bank *bank,
> +				const enum npcm_sgpio_reg reg)

The alignment looks inconsistent.

> +{
> +	switch (reg) {
> +	case READ_DATA:
> +		return gpio->base + bank->rdata_reg;
> +	case WRITE_DATA:
> +		return gpio->base + bank->wdata_reg;
> +	case EVENT_CFG:
> +		return gpio->base + bank->event_config;
> +	case EVENT_STS:
> +		return gpio->base + bank->event_status;
> +	default:
> +		/* acturally if code runs to here, it's an error case */

actually

> +		WARN(1, "Getting here is an error condition\n");
> +	}
> +}
> +
> +static const struct npcm_sgpio_bank *offset_to_bank(unsigned int offset)
> +{
> +	unsigned int bank = GPIO_BANK(offset);
> +
> +	return &npcm_sgpio_banks[bank];
> +}
> +
> +static void irqd_to_npcm_sgpio_data(struct irq_data *d,
> +				    struct npcm_sgpio **gpio,
> +				    const struct npcm_sgpio_bank **bank,
> +				    u8 *bit, int *offset)
> +{
> +	struct npcm_sgpio *internal;
> +
> +	*offset = irqd_to_hwirq(d);
> +	internal = irq_data_get_irq_chip_data(d);
> +	WARN_ON(!internal);
> +
> +	*gpio = internal;
> +	*offset -= internal->nout_sgpio;
> +	*bank = offset_to_bank(*offset);
> +	*bit = GPIO_BIT(*offset);
> +}
> +
> +static int npcm_sgpio_init_port(struct npcm_sgpio *gpio)
> +{
> +	u8 in_port, out_port, set_port, reg;
> +
> +	in_port = gpio->nin_sgpio / 8;
> +	if (gpio->nin_sgpio % 8 > 0)
> +		in_port += 1;
> +
> +	out_port = gpio->nout_sgpio / 8;
> +	if (gpio->nout_sgpio % 8 > 0)
> +		out_port += 1;
> +
> +	gpio->in_port = in_port;
> +	gpio->out_port = out_port;
> +	set_port = ((out_port & 0xf) << 4) | (in_port & 0xf);
> +	iowrite8(set_port, gpio->base + NPCM_IOXCFG2);
> +
> +	reg = ioread8(gpio->base + NPCM_IOXCFG2);
> +
> +	if (reg == set_port)
> +		return 0;
> +	else
> +		return -EINVAL;

As you used a ternary operator below:

     return reg == set_port ? 0 : -EINVAL;

> +}
> +
> +static int npcm_sgpio_dir_in(struct gpio_chip *gc, unsigned int offset)
> +{
> +	struct npcm_sgpio *gpio = gpiochip_get_data(gc);
> +
> +	return offset < gpio->nout_sgpio ? -EINVAL : 0;
> +}
> +
> +static int npcm_sgpio_dir_out(struct gpio_chip *gc, unsigned int offset, int val)
> +{
> +	struct npcm_sgpio *gpio = gpiochip_get_data(gc);
> +
> +	if (offset < gpio->nout_sgpio) {
> +		gc->set(gc, offset, val);
> +		return 0;
> +	}
> +
> +	return -EINVAL;
> +}
> +
> +static int npcm_sgpio_get_direction(struct gpio_chip *gc, unsigned int offset)
> +{
> +	struct npcm_sgpio *gpio = gpiochip_get_data(gc);
> +
> +	if (offset < gpio->nout_sgpio)
> +		return 0;
> +	return 1;

Could error codes be used here too?

> +}
> +
> +static void npcm_sgpio_set(struct gpio_chip *gc, unsigned int offset, int val)
> +{
> +	struct npcm_sgpio *gpio = gpiochip_get_data(gc);
> +	const struct  npcm_sgpio_bank *bank = offset_to_bank(offset);
> +	void __iomem *addr;
> +	u8 reg = 0;
> +
> +	addr = bank_reg(gpio, bank, WRITE_DATA);
> +	reg = ioread8(addr);
> +
> +	if (val) {
> +		reg |= (val << GPIO_BIT(offset));
> +		iowrite8(reg, addr);
> +	} else {
> +		reg &= ~(1 << GPIO_BIT(offset));
> +		iowrite8(reg, addr);
> +	}

Looks like Ziowrite8()` could be moved out of the branches.


Kind regards,

Paul


> +}
> +
> +static int npcm_sgpio_get(struct gpio_chip *gc, unsigned int offset)
> +{
> +	struct npcm_sgpio *gpio = gpiochip_get_data(gc);
> +	const struct  npcm_sgpio_bank *bank;
> +	void __iomem *addr;
> +	u8 reg;
> +	int dir;
> +
> +	dir = npcm_sgpio_get_direction(gc, offset);
> +	if (dir == 0) {
> +		bank = offset_to_bank(offset);
> +
> +		addr = bank_reg(gpio, bank, WRITE_DATA);
> +		reg = ioread8(addr);
> +		reg = (reg >> GPIO_BIT(offset)) & 0x01;
> +	} else {
> +		offset -= gpio->nout_sgpio;
> +		bank = offset_to_bank(offset);
> +
> +		addr = bank_reg(gpio, bank, READ_DATA);
> +		reg = ioread8(addr);
> +		reg = (reg >> GPIO_BIT(offset)) & 0x01;
> +	}
> +
> +	return reg;
> +}
> +
> +static void npcm_sgpio_setup_enable(struct npcm_sgpio *gpio, bool enable)
> +{
> +	u8 reg = 0;
> +
> +	reg = ioread8(gpio->base + NPCM_IOXCTS);
> +	reg = reg & ~NPCM_IOXCTS_RD_MODE;
> +	reg = reg | NPCM_IOXCTS_RD_MODE_PERIODIC;
> +
> +	if (enable) {
> +		reg |= NPCM_IOXCTS_IOXIF_EN;
> +		iowrite8(reg, gpio->base + NPCM_IOXCTS);
> +	} else {
> +		reg &= ~NPCM_IOXCTS_IOXIF_EN;
> +		iowrite8(reg, gpio->base + NPCM_IOXCTS);
> +	}
> +}
> +
> +static int npcm_sgpio_setup_clk(struct npcm_sgpio *gpio,
> +				const struct npcm_clk_cfg *clk_cfg, u32 sgpio_freq)
> +{
> +	unsigned long apb_freq;
> +	u32 sgpio_clk_div;
> +	u8 tmp;
> +	int i;
> +
> +	apb_freq = clk_get_rate(gpio->pclk);
> +	sgpio_clk_div = (apb_freq / sgpio_freq);
> +	if ((apb_freq % sgpio_freq) != 0)
> +		sgpio_clk_div += 1;
> +
> +	tmp = ioread8(gpio->base + NPCM_IOXCFG1) & ~NPCM_IOXCFG1_SFT_CLK;
> +
> +	for (i = 0; i < clk_cfg->cfg_opt; i++) {
> +		if (sgpio_clk_div >= clk_cfg->SFT_CLK[i]) {
> +			iowrite8(clk_cfg->CLK_SEL[i] | tmp, gpio->base + NPCM_IOXCFG1);
> +			return 0;
> +		}
> +	}
> +
> +	return -EINVAL;
> +}
> +
> +static void npcm_sgpio_irq_init_valid_mask(struct gpio_chip *gc,
> +					   unsigned long *valid_mask, unsigned int ngpios)
> +{
> +	struct npcm_sgpio *gpio = gpiochip_get_data(gc);
> +	int n = gpio->nin_sgpio;
> +
> +	/* input GPIOs in the high range */
> +	bitmap_set(valid_mask, gpio->nout_sgpio, n);
> +	bitmap_clear(valid_mask, 0, gpio->nout_sgpio);
> +}
> +
> +static void npcm_sgpio_irq_set_mask(struct irq_data *d, bool set)
> +{
> +	const struct npcm_sgpio_bank *bank;
> +	struct npcm_sgpio *gpio;
> +	unsigned long flags;
> +	void __iomem *addr;
> +	int offset;
> +	u16 reg, type;
> +	u8 bit;
> +
> +	irqd_to_npcm_sgpio_data(d, &gpio, &bank, &bit, &offset);
> +	addr = bank_reg(gpio, bank, EVENT_CFG);
> +
> +	spin_lock_irqsave(&gpio->lock, flags);
> +
> +	npcm_sgpio_setup_enable(gpio, false);
> +
> +	reg = ioread16(addr);
> +	if (set) {
> +		reg &= ~(NPCM_IXOEVCFG_MASK << (bit * 2));
> +	} else {
> +		type = gpio->int_type[offset];
> +		reg |= (type << (bit * 2));
> +	}
> +
> +	iowrite16(reg, addr);
> +
> +	npcm_sgpio_setup_enable(gpio, true);
> +
> +	addr = bank_reg(gpio, bank, EVENT_STS);
> +	reg = ioread8(addr);
> +	reg |= BIT(bit);
> +	iowrite8(reg, addr);
> +
> +	spin_unlock_irqrestore(&gpio->lock, flags);
> +}
> +
> +static void npcm_sgpio_irq_ack(struct irq_data *d)
> +{
> +	const struct npcm_sgpio_bank *bank;
> +	struct npcm_sgpio *gpio;
> +	unsigned long flags;
> +	void __iomem *status_addr;
> +	int offset;
> +	u8 bit;
> +
> +	irqd_to_npcm_sgpio_data(d, &gpio, &bank, &bit, &offset);
> +	status_addr = bank_reg(gpio, bank, EVENT_STS);
> +	spin_lock_irqsave(&gpio->lock, flags);
> +	iowrite8(BIT(bit), status_addr);
> +	spin_unlock_irqrestore(&gpio->lock, flags);
> +}
> +
> +static void npcm_sgpio_irq_mask(struct irq_data *d)
> +{
> +	npcm_sgpio_irq_set_mask(d, true);
> +}
> +
> +static void npcm_sgpio_irq_unmask(struct irq_data *d)
> +{
> +	npcm_sgpio_irq_set_mask(d, false);
> +}
> +
> +static int npcm_sgpio_set_type(struct irq_data *d, unsigned int type)
> +{
> +	const struct npcm_sgpio_bank *bank;
> +	irq_flow_handler_t handler;
> +	struct npcm_sgpio *gpio;
> +	unsigned long flags;
> +	void __iomem *addr;
> +	int offset;
> +	u16 reg, val;
> +	u8 bit;
> +
> +	irqd_to_npcm_sgpio_data(d, &gpio, &bank, &bit, &offset);
> +
> +	switch (type & IRQ_TYPE_SENSE_MASK) {
> +	case IRQ_TYPE_EDGE_BOTH:
> +		val = NPCM_IXOEVCFG_BOTH;
> +		handler = handle_edge_irq;
> +		break;
> +	case IRQ_TYPE_EDGE_RISING:
> +		val = NPCM_IXOEVCFG_RISING;
> +		handler = handle_edge_irq;
> +		break;
> +	case IRQ_TYPE_EDGE_FALLING:
> +		val = NPCM_IXOEVCFG_FALLING;
> +		handler = handle_edge_irq;
> +		break;
> +	case IRQ_TYPE_LEVEL_HIGH:
> +		val = NPCM_IXOEVCFG_RISING;
> +		handler = handle_level_irq;
> +		break;
> +	case IRQ_TYPE_LEVEL_LOW:
> +		val = NPCM_IXOEVCFG_FALLING;
> +		handler = handle_level_irq;
> +		break;
> +	default:
> +		return -EINVAL;
> +	}
> +
> +	gpio->int_type[offset] = val;
> +
> +	spin_lock_irqsave(&gpio->lock, flags);
> +	npcm_sgpio_setup_enable(gpio, false);
> +	addr = bank_reg(gpio, bank, EVENT_CFG);
> +	reg = ioread16(addr);
> +
> +	reg |= (val << (bit * 2));
> +
> +	iowrite16(reg, addr);
> +	npcm_sgpio_setup_enable(gpio, true);
> +	spin_unlock_irqrestore(&gpio->lock, flags);
> +
> +	irq_set_handler_locked(d, handler);
> +
> +	return 0;
> +}
> +
> +static void npcm_sgpio_irq_handler(struct irq_desc *desc)
> +{
> +	struct gpio_chip *gc = irq_desc_get_handler_data(desc);
> +	struct irq_chip *ic = irq_desc_get_chip(desc);
> +	struct npcm_sgpio *gpio = gpiochip_get_data(gc);
> +	unsigned int i, j, girq;
> +	unsigned long reg;
> +
> +	chained_irq_enter(ic, desc);
> +
> +	for (i = 0; i < ARRAY_SIZE(npcm_sgpio_banks); i++) {
> +		const struct npcm_sgpio_bank *bank = &npcm_sgpio_banks[i];
> +
> +		reg = ioread8(bank_reg(gpio, bank, EVENT_STS));
> +		for_each_set_bit(j, &reg, 8) {
> +			girq = irq_find_mapping(gc->irq.domain, i * 8 + gpio->nout_sgpio + j);
> +			generic_handle_irq(girq);
> +		}
> +	}
> +
> +	chained_irq_exit(ic, desc);
> +}
> +
> +static int npcm_sgpio_setup_irqs(struct npcm_sgpio *gpio,
> +				 struct platform_device *pdev)
> +{
> +	int rc, i;
> +	struct gpio_irq_chip *irq;
> +
> +	rc = platform_get_irq(pdev, 0);
> +	if (rc < 0)
> +		return rc;
> +
> +	gpio->irq = rc;
> +
> +	npcm_sgpio_setup_enable(gpio, false);
> +
> +	/* Disable IRQ and clear Interrupt status registers for all SGPIO Pins. */
> +	for (i = 0; i < ARRAY_SIZE(npcm_sgpio_banks); i++) {
> +		const struct npcm_sgpio_bank *bank = &npcm_sgpio_banks[i];
> +
> +		iowrite16(0x0000, bank_reg(gpio, bank, EVENT_CFG));
> +		iowrite8(0xff, bank_reg(gpio, bank, EVENT_STS));
> +	}
> +
> +	gpio->intc.name = dev_name(&pdev->dev);
> +	gpio->intc.irq_ack = npcm_sgpio_irq_ack;
> +	gpio->intc.irq_mask = npcm_sgpio_irq_mask;
> +	gpio->intc.irq_unmask = npcm_sgpio_irq_unmask;
> +	gpio->intc.irq_set_type = npcm_sgpio_set_type;
> +
> +	irq = &gpio->chip.irq;
> +	irq->chip = &gpio->intc;
> +	irq->init_valid_mask = npcm_sgpio_irq_init_valid_mask;
> +	irq->handler = handle_bad_irq;
> +	irq->default_type = IRQ_TYPE_NONE;
> +	irq->parent_handler = npcm_sgpio_irq_handler;
> +	irq->parent_handler_data = gpio;
> +	irq->parents = &gpio->irq;
> +	irq->num_parents = 1;
> +
> +	return 0;
> +}
> +
> +static const int npcm750_SFT_CLK[] = {
> +		1024, 32, 8, 4, 3, 2,
> +};
> +
> +static const u8 npcm750_CLK_SEL[] = {
> +		0x00, 0x05, 0x07, 0x0C, 0x0D, 0x0E,
> +};
> +
> +static const int npcm845_SFT_CLK[] = {
> +		1024, 32, 16, 8, 4,
> +};
> +
> +static const u8 npcm845_CLK_SEL[] = {
> +		0x00, 0x05, 0x06, 0x07, 0x0C,
> +};
> +
> +static const struct npcm_clk_cfg npcm750_sgpio_pdata = {
> +	.SFT_CLK = npcm750_SFT_CLK,
> +	.CLK_SEL = npcm750_CLK_SEL,
> +	.cfg_opt = 6,
> +};
> +
> +static const struct npcm_clk_cfg npcm845_sgpio_pdata = {
> +	.SFT_CLK = npcm845_SFT_CLK,
> +	.CLK_SEL = npcm845_CLK_SEL,
> +	.cfg_opt = 5,
> +};
> +
> +static const struct of_device_id npcm_sgpio_of_table[] = {
> +	{ .compatible = "nuvoton,npcm750-sgpio", .data = &npcm750_sgpio_pdata, },
> +	{ .compatible = "nuvoton,npcm845-sgpio", .data = &npcm845_sgpio_pdata, },
> +	{}
> +};
> +
> +MODULE_DEVICE_TABLE(of, npcm_sgpio_of_table);
> +
> +static int npcm_sgpio_probe(struct platform_device *pdev)
> +{
> +	struct npcm_sgpio *gpio;
> +	const struct npcm_clk_cfg *clk_cfg;
> +	int rc;
> +	u32 nin_gpios, nout_gpios, sgpio_freq;
> +
> +	gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
> +	if (!gpio)
> +		return -ENOMEM;
> +
> +	gpio->base = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(gpio->base))
> +		return PTR_ERR(gpio->base);
> +
> +	clk_cfg = device_get_match_data(&pdev->dev);
> +	if (!clk_cfg)
> +		return -EINVAL;
> +
> +	rc = device_property_read_u32(&pdev->dev, "nuvoton,input-ngpios", &nin_gpios);
> +	if (rc < 0) {
> +		dev_err(&pdev->dev, "Could not read ngpios property\n");
> +		return -EINVAL;
> +	}
> +
> +	rc = device_property_read_u32(&pdev->dev, "nuvoton,output-ngpios", &nout_gpios);
> +	if (rc < 0) {
> +		dev_err(&pdev->dev, "Could not read ngpios property\n");
> +		return -EINVAL;
> +	}
> +
> +	gpio->nin_sgpio = nin_gpios;
> +	gpio->nout_sgpio = nout_gpios;
> +	if (gpio->nin_sgpio > MAX_NR_HW_SGPIO || gpio->nout_sgpio > MAX_NR_HW_SGPIO) {
> +		dev_err(&pdev->dev, "Number of GPIOs exceeds the maximum of %d: input: %d output: %d\n",
> +			MAX_NR_HW_SGPIO, nin_gpios, nout_gpios);
> +		return -EINVAL;
> +	}
> +
> +	rc = device_property_read_u32(&pdev->dev, "bus-frequency", &sgpio_freq);
> +	if (rc < 0) {
> +		dev_err(&pdev->dev, "Could not read bus-frequency property\n");
> +		return -EINVAL;
> +	}
> +
> +	gpio->pclk = devm_clk_get(&pdev->dev, NULL);
> +	if (IS_ERR(gpio->pclk)) {
> +		dev_err(&pdev->dev, "Could not get pclk\n");
> +		return PTR_ERR(gpio->pclk);
> +	}
> +
> +	rc = npcm_sgpio_setup_clk(gpio, clk_cfg, sgpio_freq);
> +	if (rc < 0) {
> +		dev_err(&pdev->dev, "Failed to setup clock\n");
> +		return -EINVAL;
> +	}
> +
> +	spin_lock_init(&gpio->lock);
> +	gpio->chip.parent = &pdev->dev;
> +	gpio->chip.ngpio = gpio->nin_sgpio + gpio->nout_sgpio;
> +	gpio->chip.direction_input = npcm_sgpio_dir_in;
> +	gpio->chip.direction_output = npcm_sgpio_dir_out;
> +	gpio->chip.get_direction = npcm_sgpio_get_direction;
> +	gpio->chip.request = NULL;
> +	gpio->chip.free = NULL;
> +	gpio->chip.get = npcm_sgpio_get;
> +	gpio->chip.set = npcm_sgpio_set;
> +	gpio->chip.set_config = NULL;
> +	gpio->chip.label = dev_name(&pdev->dev);
> +	gpio->chip.base = -1;
> +
> +	rc = npcm_sgpio_init_port(gpio);
> +	if (rc < 0)
> +		return rc;
> +
> +	rc = npcm_sgpio_setup_irqs(gpio, pdev);
> +	if (rc < 0)
> +		return rc;
> +
> +	rc = devm_gpiochip_add_data(&pdev->dev, &gpio->chip, gpio);
> +	if (rc < 0)
> +		return rc;
> +
> +	npcm_sgpio_setup_enable(gpio, true);
> +	dev_info(&pdev->dev, "NPCM: SGPIO module is ready\n");
> +
> +	return 0;
> +}
> +
> +static struct platform_driver npcm_sgpio_driver = {
> +	.driver = {
> +		.name = KBUILD_MODNAME,
> +		.of_match_table = npcm_sgpio_of_table,
> +	},
> +	.probe	= npcm_sgpio_probe,
> +};
> +
> +module_platform_driver(npcm_sgpio_driver);
> +
> +MODULE_AUTHOR("Jim Liu <jjliu0@...oton.com>");
> +MODULE_AUTHOR("Joseph Liu <kwliu@...oton.com>");
> +MODULE_DESCRIPTION("Nuvoton NPCM Serial GPIO Driver");
> +MODULE_LICENSE("GPL");

Powered by blists - more mailing lists