| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Mon, 15 May 2023 12:32:19 +0530
From: Achal Verma <a-verma1@...com>
To: Nishanth Menon <nm@...com>, Vignesh Raghavendra <vigneshr@...com>,
Tero Kristo <kristo@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley <conor+dt@...nel.org>
CC: <linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
Achal Verma <a-verma1@...com>
Subject: [PATCH] arm64: dts: ti: k3-j784s4: Add initial PCIe/SerDes support for J784S4
From: Matt Ranostay <mranostay@...com>
J784S4 SoC supports two PCIE instances as follows:
* PCIE0 - 4x lanes
* PCIE1 - 4x lanes
J784S4 EVM board has the following PCIE connectors:
* PCIE0 - 4x lanes
* PCIE1 - 2x lanes
Signed-off-by: Matt Ranostay <mranostay@...com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@...com>
Signed-off-by: Achal Verma <a-verma1@...com>
---
This patch depends on:
https://lore.kernel.org/all/20230310111630.743023-1-s-vadapalli@ti.com/
https://lore.kernel.org/all/20230425131607.290707-1-j-choudhary@ti.com/
https://lore.kernel.org/all/20230401112633.2406604-1-a-verma1@ti.com/
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 65 +++++++++++
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 126 +++++++++++++++++++++
2 files changed, 191 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 75d635c9992b..27f5902f0bfb 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -261,6 +261,71 @@ &main_sdhci1 {
vqmmc-supply = <&vdd_sd_dv>;
};
+&serdes0 {
+ status = "okay";
+ serdes0_pcie_link: phy@0 {
+ reg = <0>;
+ cdns,num-lanes = <4>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_PCIE>;
+ resets = <&serdes_wiz0 1>, <&serdes_wiz0 2>,
+ <&serdes_wiz0 3>, <&serdes_wiz0 4>;
+ };
+};
+
+&serdes_wiz0 {
+ status = "okay";
+};
+
+&serdes1 {
+ status = "okay";
+ serdes1_pcie_link: phy@0 {
+ reg = <0>;
+ cdns,num-lanes = <2>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_PCIE>;
+ resets = <&serdes_wiz1 1>, <&serdes_wiz1 2>;
+ };
+};
+
+&serdes_wiz1 {
+ status = "okay";
+};
+
+&pcie0_rc {
+ status = "okay";
+ reset-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
+ phys = <&serdes1_pcie_link>;
+ phy-names = "pcie-phy";
+};
+
+&pcie0_ep {
+ phys = <&serdes1_pcie_link>;
+ phy-names = "pcie-phy";
+};
+
+&pcie1_rc {
+ status = "okay";
+ num-lanes = <2>;
+ reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>;
+ phys = <&serdes0_pcie_link>;
+ phy-names = "pcie-phy";
+};
+
+&pcie1_ep {
+ num-lanes = <2>;
+ phys = <&serdes0_pcie_link>;
+ phy-names = "pcie-phy";
+};
+
+&serdes_ln_ctrl {
+ idle-states = <J784S4_SERDES0_LANE0_PCIE1_LANE0>, <J784S4_SERDES0_LANE1_PCIE1_LANE1>,
+ <J784S4_SERDES0_LANE2_IP3_UNUSED>, <J784S4_SERDES0_LANE3_USB>,
+ <J784S4_SERDES1_LANE0_PCIE0_LANE0>, <J784S4_SERDES1_LANE1_PCIE0_LANE1>,
+ <J784S4_SERDES1_LANE2_PCIE0_LANE2>, <J784S4_SERDES1_LANE3_PCIE0_LANE3>,
+ <J784S4_SERDES2_LANE2_QSGMII_LANE1>, <J784S4_SERDES2_LANE3_QSGMII_LANE2>;
+};
+
&main_gpio0 {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index 5fa31fe2311b..206f3d206c4c 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -949,6 +949,132 @@ cpts@...d0000 {
};
};
+ pcie0_rc: pcie@...0000 {
+ compatible = "ti,j784s4-pcie-host";
+ reg = <0x00 0x02900000 0x00 0x1000>,
+ <0x00 0x02907000 0x00 0x400>,
+ <0x00 0x0d000000 0x00 0x00800000>,
+ <0x00 0x10000000 0x00 0x00001000>;
+ reg-names = "intd_cfg", "user_cfg", "reg", "cfg";
+ interrupt-names = "link_state";
+ interrupts = <GIC_SPI 318 IRQ_TYPE_EDGE_RISING>;
+ device_type = "pci";
+ ti,syscon-pcie-ctrl = <&scm_conf 0x4070>;
+ max-link-speed = <3>;
+ num-lanes = <4>;
+ power-domains = <&k3_pds 332 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 332 0>;
+ clock-names = "fck";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ bus-range = <0x0 0xff>;
+ vendor-id = <0x104c>;
+ device-id = <0xb00d>;
+ msi-map = <0x0 &gic_its 0x0 0x10000>;
+ dma-coherent;
+ ranges = <0x01000000 0x0 0x10001000 0x0 0x10001000 0x0 0x0010000>,
+ <0x02000000 0x0 0x10011000 0x0 0x10011000 0x0 0x7fef000>;
+ dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+ <0 0 0 2 &pcie0_intc 0>,
+ <0 0 0 3 &pcie0_intc 0>,
+ <0 0 0 4 &pcie0_intc 0>;
+ status = "disabled";
+
+ pcie0_intc: interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic500>;
+ interrupts = <GIC_SPI 312 IRQ_TYPE_EDGE_RISING>;
+ };
+ };
+
+ pcie0_ep: pcie-ep@...0000 {
+ compatible = "ti,j784s4-pcie-ep";
+ reg = <0x00 0x02900000 0x00 0x1000>,
+ <0x00 0x02907000 0x00 0x400>,
+ <0x00 0x0d000000 0x00 0x00800000>,
+ <0x00 0x10000000 0x00 0x08000000>;
+ reg-names = "intd_cfg", "user_cfg", "reg", "mem";
+ interrupt-names = "link_state";
+ interrupts = <GIC_SPI 318 IRQ_TYPE_EDGE_RISING>;
+ ti,syscon-pcie-ctrl = <&scm_conf 0x4070>;
+ max-link-speed = <3>;
+ num-lanes = <4>;
+ power-domains = <&k3_pds 332 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 332 0>;
+ clock-names = "fck";
+ max-functions = /bits/ 8 <6>;
+ max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
+ dma-coherent;
+ status = "disabled";
+ };
+
+ pcie1_rc: pcie@...0000 {
+ compatible = "ti,j784s4-pcie-host";
+ reg = <0x00 0x02910000 0x00 0x1000>,
+ <0x00 0x02917000 0x00 0x400>,
+ <0x00 0x0d800000 0x00 0x00800000>,
+ <0x00 0x18000000 0x00 0x00001000>;
+ reg-names = "intd_cfg", "user_cfg", "reg", "cfg";
+ interrupt-names = "link_state";
+ interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
+ device_type = "pci";
+ ti,syscon-pcie-ctrl = <&scm_conf 0x4074>;
+ max-link-speed = <3>;
+ num-lanes = <4>;
+ power-domains = <&k3_pds 333 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 333 0>;
+ clock-names = "fck";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ bus-range = <0x0 0xff>;
+ vendor-id = <0x104c>;
+ device-id = <0xb013>;
+ msi-map = <0x0 &gic_its 0x10000 0x10000>;
+ dma-coherent;
+ ranges = <0x01000000 0x0 0x18001000 0x00 0x18001000 0x0 0x0010000>,
+ <0x02000000 0x0 0x18011000 0x00 0x18011000 0x0 0x7fef000>;
+ dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+ <0 0 0 2 &pcie1_intc 0>,
+ <0 0 0 3 &pcie1_intc 0>,
+ <0 0 0 4 &pcie1_intc 0>;
+ status = "disabled";
+
+ pcie1_intc: interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&gic500>;
+ interrupts = <GIC_SPI 324 IRQ_TYPE_EDGE_RISING>;
+ };
+ };
+
+ pcie1_ep: pcie-ep@...0000 {
+ compatible = "ti,j784s4-pcie-ep";
+ reg = <0x00 0x02910000 0x00 0x1000>,
+ <0x00 0x02917000 0x00 0x400>,
+ <0x00 0x0d800000 0x00 0x00800000>,
+ <0x00 0x18000000 0x00 0x08000000>;
+ reg-names = "intd_cfg", "user_cfg", "reg", "mem";
+ interrupt-names = "link_state";
+ interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
+ ti,syscon-pcie-ctrl = <&scm_conf 0x4074>;
+ max-link-speed = <3>;
+ num-lanes = <4>;
+ power-domains = <&k3_pds 333 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 333 0>;
+ clock-names = "fck";
+ max-functions = /bits/ 8 <6>;
+ max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
+ dma-coherent;
+ status = "disabled";
+ };
+
main_mcan0: can@...1000 {
compatible = "bosch,m_can";
reg = <0x00 0x02701000 0x00 0x200>,
--
2.25.1
Powered by blists - more mailing lists