| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20230517072806.13170-1-quic_kathirav@quicinc.com>
Date: Wed, 17 May 2023 12:58:06 +0530
From: Kathiravan T <quic_kathirav@...cinc.com>
To: <agross@...nel.org>, <andersson@...nel.org>,
<konrad.dybcio@...aro.org>, <robh+dt@...nel.org>,
<krzysztof.kozlowski+dt@...aro.org>, <conor+dt@...nel.org>,
<linux-arm-msm@...r.kernel.org>, <devicetree@...r.kernel.org>,
<linux-kernel@...r.kernel.org>
CC: Kathiravan T <quic_kathirav@...cinc.com>
Subject: [PATCH V3] arm64: dts: qcom: ipq9574: add few device nodes
Add QUP(SPI / I2C) peripheral, PRNG, WDOG and the remaining UART nodes.
While at it, enable the SPI NOR in RDP433 board.
Signed-off-by: Kathiravan T <quic_kathirav@...cinc.com>
---
Changed since V2:
- V2 didn't apply properly on below series, fixed it now
Changes since V1:
- Dropped the WDT binding patch, since it is already part of
linux-next
- Rebased on the below series
https://lore.kernel.org/linux-arm-msm/75a408c2-3d41-95a3-5c48-a68c84ba4f57@quicinc.com/T/#t
arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 21 ++
arch/arm64/boot/dts/qcom/ipq9574.dtsi | 202 ++++++++++++++++++++
2 files changed, 223 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
index 2ce8e09e7565..7be578017bf7 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
@@ -29,6 +29,20 @@
status = "okay";
};
+&blsp1_spi0 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ flash@0 {
+ compatible = "micron,n25q128a11", "jedec,spi-nor";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ };
+};
+
&sdhc_1 {
pinctrl-0 = <&sdc_default_state>;
pinctrl-names = "default";
@@ -77,6 +91,13 @@
bias-pull-down;
};
};
+
+ spi_0_pins: spi-0-state {
+ pins = "gpio11", "gpio12", "gpio13", "gpio14";
+ function = "blsp0_spi";
+ drive-strength = <8>;
+ bias-disable;
+ };
};
&xo_board_clk {
diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
index ccf70bafabab..fea15f3cf910 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
@@ -116,6 +116,13 @@
#size-cells = <1>;
ranges = <0 0 0 0xffffffff>;
+ rng: rng@...00 {
+ compatible = "qcom,prng-ee";
+ reg = <0x000e3000 0x1000>;
+ clocks = <&gcc GCC_PRNG_AHB_CLK>;
+ clock-names = "core";
+ };
+
tlmm: pinctrl@...0000 {
compatible = "qcom,ipq9574-tlmm";
reg = <0x01000000 0x300000>;
@@ -178,6 +185,36 @@
status = "disabled";
};
+ blsp_dma: dma-controller@...4000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x07884000 0x2b000>;
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ };
+
+ blsp1_uart0: serial@...f000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078af000 0x200>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ blsp1_uart1: serial@...0000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b0000 0x200>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
blsp1_uart2: serial@...1000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x078b1000 0x200>;
@@ -188,6 +225,163 @@
status = "disabled";
};
+ blsp1_uart3: serial@...2000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b2000 0x200>;
+ interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART4_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ blsp1_uart4: serial@...3000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b3000 0x200>;
+ interrupts = <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART5_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ blsp1_uart5: serial@...4000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b4000 0x200>;
+ interrupts = <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART6_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ blsp1_spi0: spi@...5000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b5000 0x600>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ blsp1_i2c1: i2c@...6000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b6000 0x600>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ blsp1_spi1: spi@...6000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b6000 0x600>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ blsp1_i2c2: i2c@...7000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b7000 0x600>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 16>, <&blsp_dma 17>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ blsp1_spi2: spi@...7000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b7000 0x600>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 16>, <&blsp_dma 17>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ blsp1_i2c3: i2c@...8000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b8000 0x600>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 18>, <&blsp_dma 19>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ blsp1_spi3: spi@...8000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b8000 0x600>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ spi-max-frequency = <50000000>;
+ clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 18>, <&blsp_dma 19>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ blsp1_i2c4: i2c@...9000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b9000 0x600>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 20>, <&blsp_dma 21>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ blsp1_spi4: spi@...9000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b9000 0x600>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 20>, <&blsp_dma 21>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
intc: interrupt-controller@...0000 {
compatible = "qcom,msm-qgic2";
reg = <0x0b000000 0x1000>, /* GICD */
@@ -220,6 +414,14 @@
};
};
+ watchdog: watchdog@...7000 {
+ compatible = "qcom,apss-wdt-ipq9574", "qcom,kpss-wdt";
+ reg = <0x0b017000 0x1000>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&sleep_clk>;
+ timeout-sec = <30>;
+ };
+
timer@...0000 {
compatible = "arm,armv7-timer-mem";
reg = <0x0b120000 0x1000>;
--
2.17.1
Powered by blists - more mailing lists