| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <b49904649a363f40dc9c4d3fa275e42129562082.1684767562.git.michal.simek@amd.com>
Date: Mon, 22 May 2023 16:59:48 +0200
From: Michal Simek <michal.simek@....com>
To: <linux-kernel@...r.kernel.org>, <monstr@...str.eu>,
<michal.simek@...inx.com>, <git@...inx.com>
CC: Amit Kumar Mahapatra <amit.kumar-mahapatra@...inx.com>,
Ashok Reddy Soma <ashok.reddy.soma@...inx.com>,
Conor Dooley <conor+dt@...nel.org>,
"Krzysztof Kozlowski" <krzysztof.kozlowski+dt@...aro.org>,
Laurent Pinchart <laurent.pinchart@...asonboard.com>,
Parth Gajjar <parth.gajjar@....com>,
"Rob Herring" <robh+dt@...nel.org>,
Vishal Sagar <vishal.sagar@....com>,
<devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>
Subject: [PATCH v2 1/6] arm64: zynqmp: Describe TI phy as ethernet-phy-id
TI DP83867 is using strapping based on MIO pins. Tristate setup can
influence PHY address. That's why switch description with ethernet-phy-id
compatible string which enable calling reset. PHY itself setups phy address
after power up or reset. Phy reset is done via gpio.
Signed-off-by: Michal Simek <michal.simek@....com>
---
Changes in v2:
- fix typo in commit message
Checkpatch is reporting issue
warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented
but it should be fully aligned with
Documentation/devicetree/bindings/net/ethernet-phy.yaml
c&p more details from v1 version:
Phy has some pins which is using for strapping for phy address after phy
reset or power on. Pretty much it is resistor array which based on
datasheet is decoded to certain phy address.
And because some phy pins are also used as data pin for RGMII they are
connected via MIO pins on a silicon. That's why IO block output setting
really matter here because it changes resistor array and it moves phy
address.
That's why there is a need to do proper IO pin setup and after it call phy
reset to get it to address which was decided by PCB designer.
---
.../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 23 +++++++++++------
.../boot/dts/xilinx/zynqmp-zcu102-revB.dts | 25 +++++++++++--------
.../boot/dts/xilinx/zynqmp-zcu104-revA.dts | 22 ++++++++++------
.../boot/dts/xilinx/zynqmp-zcu104-revC.dts | 22 ++++++++++------
.../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 22 ++++++++++------
.../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 22 ++++++++++------
6 files changed, 90 insertions(+), 46 deletions(-)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
index 230ef94d5dcb..f36353a51863 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
@@ -2,7 +2,8 @@
/*
* dts file for Xilinx ZynqMP ZCU102 RevA
*
- * (C) Copyright 2015 - 2021, Xilinx, Inc.
+ * (C) Copyright 2015 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
*
* Michal Simek <michal.simek@....com>
*/
@@ -200,13 +201,19 @@ &gem3 {
phy-mode = "rgmii-id";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gem3_default>;
- phy0: ethernet-phy@21 {
- reg = <21>;
- ti,rx-internal-delay = <0x8>;
- ti,tx-internal-delay = <0xa>;
- ti,fifo-depth = <0x1>;
- ti,dp83867-rxctrl-strap-quirk;
- /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@21 {
+ #phy-cells = <1>;
+ compatible = "ethernet-phy-id2000.a231";
+ reg = <21>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
+ reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
+ };
};
};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
index 63419deb5b33..3c28130909bc 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
@@ -2,7 +2,8 @@
/*
* dts file for Xilinx ZynqMP ZCU102 RevB
*
- * (C) Copyright 2016 - 2021, Xilinx, Inc.
+ * (C) Copyright 2016 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
*
* Michal Simek <michal.simek@....com>
*/
@@ -16,16 +17,20 @@ / {
&gem3 {
phy-handle = <&phyc>;
- phyc: ethernet-phy@c {
- reg = <0xc>;
- ti,rx-internal-delay = <0x8>;
- ti,tx-internal-delay = <0xa>;
- ti,fifo-depth = <0x1>;
- ti,dp83867-rxctrl-strap-quirk;
- /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
+ mdio: mdio {
+ phyc: ethernet-phy@c {
+ #phy-cells = <0x1>;
+ compatible = "ethernet-phy-id2000.a231";
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
+ reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
+ };
+ /* Cleanup from RevA */
+ /delete-node/ ethernet-phy@21;
};
- /* Cleanup from RevA */
- /delete-node/ ethernet-phy@21;
};
/* Fix collision with u61 */
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
index d178a4f898c9..3fd47725c2c8 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
@@ -2,7 +2,8 @@
/*
* dts file for Xilinx ZynqMP ZCU104
*
- * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ * (C) Copyright 2017 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
*
* Michal Simek <michal.simek@....com>
*/
@@ -109,12 +110,19 @@ &gem3 {
phy-mode = "rgmii-id";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gem3_default>;
- phy0: ethernet-phy@c {
- reg = <0xc>;
- ti,rx-internal-delay = <0x8>;
- ti,tx-internal-delay = <0xa>;
- ti,fifo-depth = <0x1>;
- ti,dp83867-rxctrl-strap-quirk;
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@c {
+ #phy-cells = <1>;
+ compatible = "ethernet-phy-id2000.a231";
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
+ reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
+ };
};
};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
index 38b11594c074..4f6429caecff 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
@@ -2,7 +2,8 @@
/*
* dts file for Xilinx ZynqMP ZCU104
*
- * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ * (C) Copyright 2017 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
*
* Michal Simek <michal.simek@....com>
*/
@@ -114,12 +115,19 @@ &gem3 {
phy-mode = "rgmii-id";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gem3_default>;
- phy0: ethernet-phy@c {
- reg = <0xc>;
- ti,rx-internal-delay = <0x8>;
- ti,tx-internal-delay = <0xa>;
- ti,fifo-depth = <0x1>;
- ti,dp83867-rxctrl-strap-quirk;
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@c {
+ #phy-cells = <1>;
+ compatible = "ethernet-phy-id2000.a231";
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
+ reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
+ };
};
};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
index 8af0879806cf..8c3fa3fe28d5 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
@@ -2,7 +2,8 @@
/*
* dts file for Xilinx ZynqMP ZCU106
*
- * (C) Copyright 2016 - 2021, Xilinx, Inc.
+ * (C) Copyright 2016 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
*
* Michal Simek <michal.simek@....com>
*/
@@ -212,12 +213,19 @@ &gem3 {
phy-mode = "rgmii-id";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gem3_default>;
- phy0: ethernet-phy@c {
- reg = <0xc>;
- ti,rx-internal-delay = <0x8>;
- ti,tx-internal-delay = <0xa>;
- ti,fifo-depth = <0x1>;
- ti,dp83867-rxctrl-strap-quirk;
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@c {
+ #phy-cells = <1>;
+ reg = <0xc>;
+ compatible = "ethernet-phy-id2000.a231";
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
+ reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
+ };
};
};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
index f76687914e30..0d9b6081dff6 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
@@ -2,7 +2,8 @@
/*
* dts file for Xilinx ZynqMP ZCU111
*
- * (C) Copyright 2017 - 2021, Xilinx, Inc.
+ * (C) Copyright 2017 - 2022, Xilinx, Inc.
+ * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
*
* Michal Simek <michal.simek@....com>
*/
@@ -172,12 +173,19 @@ &gem3 {
phy-mode = "rgmii-id";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gem3_default>;
- phy0: ethernet-phy@c {
- reg = <0xc>;
- ti,rx-internal-delay = <0x8>;
- ti,tx-internal-delay = <0xa>;
- ti,fifo-depth = <0x1>;
- ti,dp83867-rxctrl-strap-quirk;
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@c {
+ #phy-cells = <1>;
+ compatible = "ethernet-phy-id2000.a231";
+ reg = <0xc>;
+ ti,rx-internal-delay = <0x8>;
+ ti,tx-internal-delay = <0xa>;
+ ti,fifo-depth = <0x1>;
+ ti,dp83867-rxctrl-strap-quirk;
+ reset-gpios = <&tca6416_u22 6 GPIO_ACTIVE_LOW>;
+ };
};
};
--
2.36.1
Powered by blists - more mailing lists