| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <ZG97u6GN/pzDk6zy@debian>
Date: Thu, 25 May 2023 17:16:11 +0200
From: Ramón Nordin Rodriguez
<ramon.nordin.rodriguez@...roamp.se>
To: Parthiban Veerasooran <Parthiban.Veerasooran@...rochip.com>
Cc: andrew@...n.ch, hkallweit1@...il.com, linux@...linux.org.uk,
davem@...emloft.net, edumazet@...gle.com, kuba@...nel.org,
pabeni@...hat.com, netdev@...r.kernel.org,
linux-kernel@...r.kernel.org, horatiu.vultur@...rochip.com,
Woojung.Huh@...rochip.com, Nicolas.Ferre@...rochip.com,
Thorsten.Kummermehr@...rochip.com
Subject: Re: [PATCH net-next v3 6/6] net: phy: microchip_t1s: add support for
Microchip LAN865x Rev.B0 PHYs
On Wed, May 24, 2023 at 08:15:39PM +0530, Parthiban Veerasooran wrote:
> Add support for the Microchip LAN865x Rev.B0 10BASE-T1S Internal PHYs
> (LAN8650/1). The LAN865x combines a Media Access Controller (MAC) and an
> internal 10BASE-T1S Ethernet PHY to access 10BASE‑T1S networks. As
> LAN867X and LAN865X are using the same function for the read_status,
> rename the function as lan86xx_read_status.
>
> Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@...rochip.com>
> ---
> drivers/net/phy/microchip_t1s.c | 184 +++++++++++++++++++++++++++++++-
> 1 file changed, 181 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/net/phy/microchip_t1s.c b/drivers/net/phy/microchip_t1s.c
> index 6f9e197d8623..00c4c23906ce 100644
> --- a/drivers/net/phy/microchip_t1s.c
> +++ b/drivers/net/phy/microchip_t1s.c
> @@ -4,6 +4,7 @@
> *
> * Support: Microchip Phys:
> * lan8670/1/2 Rev.B1
> + * lan8650/1 Rev.B0 Internal PHYs
> */
>
> #include <linux/kernel.h>
> @@ -11,11 +12,19 @@
> #include <linux/phy.h>
>
> #define PHY_ID_LAN867X_REVB1 0x0007C162
> +#define PHY_ID_LAN865X_REVB0 0x0007C1B3
>
> #define LAN867X_REG_STS2 0x0019
>
> #define LAN867x_RESET_COMPLETE_STS BIT(11)
>
> +#define LAN865X_REG_CFGPARAM_ADDR 0x00D8
> +#define LAN865X_REG_CFGPARAM_DATA 0x00D9
> +#define LAN865X_REG_CFGPARAM_CTRL 0x00DA
> +#define LAN865X_REG_STS2 0x0019
> +
> +#define LAN865X_CFGPARAM_READ_ENABLE BIT(1)
> +
> /* The arrays below are pulled from the following table from AN1699
> * Access MMD Address Value Mask
> * RMW 0x1F 0x00D0 0x0002 0x0E03
> @@ -50,6 +59,164 @@ static const u16 lan867x_revb1_fixup_masks[12] = {
> 0x0600, 0x7F00, 0x2000, 0xFFFF,
> };
>
> +/* LAN865x Rev.B0 configuration parameters from AN1760 */
> +static const u32 lan865x_revb0_fixup_registers[28] = {
> + 0x0091, 0x0081, 0x0043, 0x0044,
> + 0x0045, 0x0053, 0x0054, 0x0055,
> + 0x0040, 0x0050, 0x00D0, 0x00E9,
> + 0x00F5, 0x00F4, 0x00F8, 0x00F9,
> + 0x00B0, 0x00B1, 0x00B2, 0x00B3,
> + 0x00B4, 0x00B5, 0x00B6, 0x00B7,
> + 0x00B8, 0x00B9, 0x00BA, 0x00BB,
> +};
> +
> +static const u16 lan865x_revb0_fixup_values[28] = {
> + 0x9660, 0x00C0, 0x00FF, 0xFFFF,
> + 0x0000, 0x00FF, 0xFFFF, 0x0000,
> + 0x0002, 0x0002, 0x5F21, 0x9E50,
> + 0x1CF8, 0xC020, 0x9B00, 0x4E53,
> + 0x0103, 0x0910, 0x1D26, 0x002A,
> + 0x0103, 0x070D, 0x1720, 0x0027,
> + 0x0509, 0x0E13, 0x1C25, 0x002B,
> +};
> +
> +static const u16 lan865x_revb0_fixup_cfg_regs[5] = {
> + 0x0084, 0x008A, 0x00AD, 0x00AE, 0x00AF
> +};
> +
> +/* Pulled from AN1760 describing 'indirect read'
> + *
> + * write_register(0x4, 0x00D8, addr)
> + * write_register(0x4, 0x00DA, 0x2)
> + * return (int8)(read_register(0x4, 0x00D9))
> + *
> + * 0x4 refers to memory map selector 4, which maps to MDIO_MMD_VEND2
> + */
> +static int lan865x_revb0_indirect_read(struct phy_device *phydev, u16 addr)
> +{
> + int ret;
> +
> + ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, LAN865X_REG_CFGPARAM_ADDR,
> + addr);
> + if (ret)
> + return ret;
> +
> + ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, LAN865X_REG_CFGPARAM_CTRL,
> + LAN865X_CFGPARAM_READ_ENABLE);
> + if (ret)
> + return ret;
> +
> + return phy_read_mmd(phydev, MDIO_MMD_VEND2, LAN865X_REG_CFGPARAM_DATA);
> +}
> +
> +/* This is pulled straight from AN1760 from 'calculation of offset 1' &
> + * 'calculation of offset 2'
> + */
> +static int lan865x_generate_cfg_offsets(struct phy_device *phydev, s8 offsets[2])
> +{
> + const u16 fixup_regs[2] = {0x0004, 0x0008};
> + int ret;
> +
> + for (int i = 0; i < ARRAY_SIZE(fixup_regs); i++) {
> + ret = lan865x_revb0_indirect_read(phydev, fixup_regs[i]);
> + if (ret < 0)
> + return ret;
> + if (ret & BIT(4))
> + offsets[i] = ret | 0xE0;
> + else
> + offsets[i] = ret;
> + }
> +
> + return 0;
> +}
> +
> +static int lan865x_read_cfg_params(struct phy_device *phydev, u16 cfg_params[])
> +{
> + int ret;
> +
> + for (int i = 0; i < ARRAY_SIZE(lan865x_revb0_fixup_cfg_regs); i++) {
> + ret = phy_read_mmd(phydev, MDIO_MMD_VEND2,
> + lan865x_revb0_fixup_cfg_regs[i]);
> + if (ret < 0)
> + return ret;
> + cfg_params[i] = (u16)ret;
> + }
> +
> + return 0;
> +}
> +
> +static int lan865x_write_cfg_params(struct phy_device *phydev, u16 cfg_params[])
> +{
> + int ret;
> +
> + for (int i = 0; i < ARRAY_SIZE(lan865x_revb0_fixup_cfg_regs); i++) {
> + ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
> + lan865x_revb0_fixup_cfg_regs[i],
> + cfg_params[i]);
> + if (ret)
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int lan865x_setup_cfgparam(struct phy_device *phydev)
> +{
> + u16 cfg_params[ARRAY_SIZE(lan865x_revb0_fixup_cfg_regs)];
> + u16 cfg_results[5];
> + s8 offsets[2];
> + int ret;
> +
> + ret = lan865x_generate_cfg_offsets(phydev, offsets);
> + if (ret)
> + return ret;
> +
> + ret = lan865x_read_cfg_params(phydev, cfg_params);
> + if (ret)
> + return ret;
> +
> + cfg_results[0] = (cfg_params[0] & 0x000F) |
> + FIELD_PREP(GENMASK(15, 10), 9 + offsets[0]) |
> + FIELD_PREP(GENMASK(15, 4), 14 + offsets[0]);
> + cfg_results[1] = (cfg_params[1] & 0x03FF) |
> + FIELD_PREP(GENMASK(15, 10), 40 + offsets[1]);
> + cfg_results[2] = (cfg_params[2] & 0xC0C0) |
> + FIELD_PREP(GENMASK(15, 8), 5 + offsets[0]) |
> + (9 + offsets[0]);
> + cfg_results[3] = (cfg_params[3] & 0xC0C0) |
> + FIELD_PREP(GENMASK(15, 8), 9 + offsets[0]) |
> + (14 + offsets[0]);
> + cfg_results[4] = (cfg_params[4] & 0xC0C0) |
> + FIELD_PREP(GENMASK(15, 8), 17 + offsets[0]) |
> + (22 + offsets[0]);
> +
> + return lan865x_write_cfg_params(phydev, cfg_results);
> +}
> +
> +static int lan865x_revb0_config_init(struct phy_device *phydev)
> +{
> + int ret;
> +
> + /* Reference to AN1760
> + * https://ww1.microchip.com/downloads/aemDocuments/documents/AIS/ProductDocuments/SupportingCollateral/AN-LAN8650-1-Configuration-60001760.pdf
> + */
> + for (int i = 0; i < ARRAY_SIZE(lan865x_revb0_fixup_registers); i++) {
> + ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
> + lan865x_revb0_fixup_registers[i],
> + lan865x_revb0_fixup_values[i]);
> + if (ret)
> + return ret;
> + }
> + /* Function to calculate and write the configuration parameters in the
> + * 0x0084, 0x008A, 0x00AD, 0x00AE and 0x00AF registers (from AN1760)
> + */
> + ret = lan865x_setup_cfgparam(phydev);
Nit, you could return the result of lan865x_setup_cfgparam directly
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +
> static int lan867x_revb1_config_init(struct phy_device *phydev)
> {
> /* HW quirk: Microchip states in the application note (AN1699) for the phy
> @@ -107,7 +274,7 @@ static int lan867x_revb1_config_init(struct phy_device *phydev)
> return 0;
> }
>
> -static int lan867x_read_status(struct phy_device *phydev)
> +static int lan86xx_read_status(struct phy_device *phydev)
> {
> /* The phy has some limitations, namely:
> * - always reports link up
> @@ -128,17 +295,28 @@ static struct phy_driver microchip_t1s_driver[] = {
> .name = "LAN867X Rev.B1",
> .features = PHY_BASIC_T1S_P2MP_FEATURES,
> .config_init = lan867x_revb1_config_init,
> - .read_status = lan867x_read_status,
> + .read_status = lan86xx_read_status,
> .get_plca_cfg = genphy_c45_plca_get_cfg,
> .set_plca_cfg = genphy_c45_plca_set_cfg,
> .get_plca_status = genphy_c45_plca_get_status,
> - }
> + },
> + {
> + PHY_ID_MATCH_EXACT(PHY_ID_LAN865X_REVB0),
> + .name = "LAN865X Rev.B0 Internal Phy",
> + .features = PHY_BASIC_T1S_P2MP_FEATURES,
> + .config_init = lan865x_revb0_config_init,
> + .read_status = lan86xx_read_status,
> + .get_plca_cfg = genphy_c45_plca_get_cfg,
> + .set_plca_cfg = genphy_c45_plca_set_cfg,
> + .get_plca_status = genphy_c45_plca_get_status,
> + },
> };
>
> module_phy_driver(microchip_t1s_driver);
>
> static struct mdio_device_id __maybe_unused tbl[] = {
> { PHY_ID_MATCH_EXACT(PHY_ID_LAN867X_REVB1) },
> + { PHY_ID_MATCH_EXACT(PHY_ID_LAN865X_REVB0) },
> { }
> };
>
> --
> 2.34.1
>
Powered by blists - more mailing lists