[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <da01a33d-a4f9-1086-3365-5a0528db16d9@linaro.org>
Date: Wed, 31 May 2023 22:14:48 +0200
From: Konrad Dybcio <konrad.dybcio@...aro.org>
To: Krzysztof Kozlowski <krzysztof.kozlowski@...aro.org>,
Srinivas Kandagatla <srinivas.kandagatla@...aro.org>,
andersson@...nel.org, robh+dt@...nel.org,
krzysztof.kozlowski+dt@...aro.org
Cc: johan+linaro@...nel.org, agross@...nel.org,
mturquette@...libre.com, sboyd@...nel.org, conor+dt@...nel.org,
linux-arm-msm@...r.kernel.org, linux-clk@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v2 5/6] arm64: dts: qcom: sc8280xp: add resets for
soundwire controllers
On 31.05.2023 22:03, Krzysztof Kozlowski wrote:
> On 25/05/2023 14:29, Srinivas Kandagatla wrote:
>> Soundwire controllers on sc8280xp needs an explicit reset, add
>> support for this.
>>
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@...aro.org>
>> ---
>> arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 23 +++++++++++++++++++++++
>> 1 file changed, 23 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
>> index 6730349e34f4..39be2e89ce05 100644
>> --- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
>> @@ -6,6 +6,7 @@
>>
>> #include <dt-bindings/clock/qcom,dispcc-sc8280xp.h>
>> #include <dt-bindings/clock/qcom,gcc-sc8280xp.h>
>> +#include <dt-bindings/clock/qcom,lpasscc-sc8280xp.h>
>> #include <dt-bindings/clock/qcom,rpmh.h>
>> #include <dt-bindings/interconnect/qcom,osm-l3.h>
>> #include <dt-bindings/interconnect/qcom,sc8280xp.h>
>> @@ -2560,6 +2561,8 @@
>> interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
>> clocks = <&rxmacro>;
>> clock-names = "iface";
>> + resets = <&lpass_audiocc LPASS_AUDIO_SWR_RX_CGCR>;
>> + reset-names = "swr_audio_cgcr";
>> label = "RX";
>>
>> qcom,din-ports = <0>;
>> @@ -2634,6 +2637,8 @@
>> interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
>> clocks = <&wsamacro>;
>> clock-names = "iface";
>> + resets = <&lpass_audiocc LPASS_AUDIO_SWR_WSA_CGCR>;
>> + reset-names = "swr_audio_cgcr";
>> label = "WSA";
>>
>> qcom,din-ports = <2>;
>> @@ -2656,6 +2661,14 @@
>> status = "disabled";
>> };
>>
>> + lpass_audiocc: clock-controller@...9000 {
>> + compatible = "qcom,sc8280xp-lpassaudiocc";
>> + reg = <0 0x032a9000 0 0x1000>;
>> + qcom,adsp-pil-mode;
>
> Here and...
>
>> + #clock-cells = <1>;
>> + #reset-cells = <1>;
>> + };
>> +
>> swr2: soundwire-controller@...0000 {
>> compatible = "qcom,soundwire-v1.6.0";
>> reg = <0 0x03330000 0 0x2000>;
>> @@ -2665,6 +2678,8 @@
>>
>> clocks = <&txmacro>;
>> clock-names = "iface";
>> + resets = <&lpasscc LPASS_AUDIO_SWR_TX_CGCR>;
>> + reset-names = "swr_audio_cgcr";
>> label = "TX";
>> #sound-dai-cells = <1>;
>> #address-cells = <2>;
>> @@ -2901,6 +2916,14 @@
>> };
>> };
>>
>> + lpasscc: clock-controller@...0000 {
>> + compatible = "qcom,sc8280xp-lpasscc";
>> + reg = <0 0x033e0000 0 0x12000>;
>> + qcom,adsp-pil-mode;
>
> ... here - where do you use these properties? Driver ignores them.
>
> AFAIR, these were only for sc7280 where we supported two variants for audio.
Smells like pure copypasta - we don't support any 8280xp chromebooks (not
even sure if any exist) and WP devices have a normal TZ+PAS setup
Konrad
>
> Best regards,
> Krzysztof
>
Powered by blists - more mailing lists