| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAJ+vNU2Wn0jf8QyZsGiw3f=XThZEfXajhGJTmZz2mnJXgprAhQ@mail.gmail.com>
Date: Tue, 18 Jul 2023 14:16:22 -0700
From: Tim Harvey <tharvey@...eworks.com>
To: Shawn Guo <shawnguo@...nel.org>
Cc: linux-arm-kernel@...ts.infradead.org,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley <conor+dt@...nel.org>,
Sascha Hauer <s.hauer@...gutronix.de>,
Pengutronix Kernel Team <kernel@...gutronix.de>,
Fabio Estevam <festevam@...il.com>,
NXP Linux Team <linux-imx@....com>,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH 2/2] arm64: dts: freescale: Add imx8mp-venice-gw71xx-2x
On Sun, Jul 16, 2023 at 5:27 PM Shawn Guo <shawnguo@...nel.org> wrote:
>
> On Wed, Jun 07, 2023 at 10:07:24AM -0700, Tim Harvey wrote:
> > The Gateworks imx8mp-venice-gw71xx-2x consists of a SOM + baseboard.
> >
> > The GW702x SOM contains the following:
> > - i.MX8M Plus SoC
> > - LPDDR4 memory
> > - eMMC Boot device
> > - Gateworks System Controller (GSC) with integrated EEPROM, button
> > controller, and ADC's
> > - PMIC
> > - SOM connector providing:
> > - eQoS GbE MII
> > - 1x SPI
> > - 2x I2C
> > - 4x UART
> > - 2x USB 3.0
> > - 1x PCI
> > - 1x SDIO (4-bit 3.3V)
> > - 1x SDIO (4-bit 3.3V/1.8V)
> > - GPIO
> >
> > The GW71xx Baseboard contains the following:
> > - GPS
> > - RJ45 GbE (eQoS)
> > - off-board I/O connector with UART, I2C, SPI, GPIO
> > - EERPOM
> > - PCIe clock generator
> > - full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
> > - USB Type-C with USB 2.0 host and peripheral support
> > - Wide range DC input supply
> >
> > Signed-off-by: Tim Harvey <tharvey@...eworks.com>
> > ---
> > arch/arm64/boot/dts/freescale/Makefile | 1 +
> > .../dts/freescale/imx8mp-venice-gw71xx-2x.dts | 19 ++
> > .../dts/freescale/imx8mp-venice-gw71xx.dtsi | 236 ++++++++++++++++++
> > 3 files changed, 256 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw71xx-2x.dts
> > create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-venice-gw71xx.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> > index 62f22b77b38b..b3bb823d0168 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -101,6 +101,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-icore-mx8mp-edimm2.2.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mp-msc-sm2s-ep1.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mp-tqma8mpql-mba8mpxl.dtb
> > +dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw71xx-2x.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw74xx.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw7905-2x.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-nonwifi-dahlia.dtb
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw71xx-2x.dts b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw71xx-2x.dts
> > new file mode 100644
> > index 000000000000..53120fc9cd7f
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw71xx-2x.dts
> > @@ -0,0 +1,19 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright 2023 Gateworks Corporation
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "imx8mp.dtsi"
> > +#include "imx8mp-venice-gw702x.dtsi"
> > +#include "imx8mp-venice-gw71xx.dtsi"
> > +
> > +/ {
> > + model = "Gateworks Venice GW71xx-2x i.MX8MP Development Kit";
> > + compatible = "gateworks,imx8mp-gw71xx-2x", "fsl,imx8mp";
> > +
> > + chosen {
> > + stdout-path = &uart2;
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw71xx.dtsi
> > new file mode 100644
> > index 000000000000..86999f52d4b2
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw71xx.dtsi
> > @@ -0,0 +1,236 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright 2023 Gateworks Corporation
> > + */
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/leds/common.h>
> > +#include <dt-bindings/phy/phy-imx8-pcie.h>
> > +
> > +/ {
> > + led-controller {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_gpio_leds>;
> > +
> > + led-0 {
> > + function = LED_FUNCTION_STATUS;
> > + color = <LED_COLOR_ID_GREEN>;
> > + gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
> > + default-state = "on";
> > + linux,default-trigger = "heartbeat";
> > + };
> > +
> > + led-1 {
> > + function = LED_FUNCTION_STATUS;
> > + color = <LED_COLOR_ID_RED>;
> > + gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;
> > + default-state = "off";
> > + };
> > + };
> > +
> > + pcie0_refclk: pcie0-refclk {
>
> Can we name the node clock-xxx?
>
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <100000000>;
> > + };
> > +
> > + pps {
> > + compatible = "pps-gpio";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pps>;
> > + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
> > + status = "okay";
> > + };
> > +};
> > +
> > +/* off-board header */
> > +&ecspi2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_spi2>;
> > + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +};
> > +
> > +&gpio4 {
> > + gpio-line-names =
> > + "", "", "", "",
> > + "", "", "", "",
> > + "dio1", "", "", "dio0",
> > + "", "", "pci_usb_sel", "",
> > + "", "", "", "",
> > + "", "", "", "",
> > + "dio3", "", "dio2", "",
> > + "pci_wdis#", "", "", "";
> > +};
> > +
> > +&i2c2 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +
> > + accelerometer@19 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_accel>;
> > + compatible = "st,lis2de12";
> > + reg = <0x19>;
>
> Can we start the property list from these two?
>
> > + st,drdy-int-pin = <1>;
> > + interrupt-parent = <&gpio4>;
> > + interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
> > + interrupt-names = "INT1";
> > + };
> > +};
> > +
> > +&pcie_phy {
> > + fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
> > + fsl,clkreq-unsupported;
> > + clocks = <&pcie0_refclk>;
> > + clock-names = "ref";
> > + status = "okay";
> > +};
> > +
> > +&pcie {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pcie0>;
> > + reset-gpio = <&gpio4 29 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +};
> > +
> > +/* GPS */
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
> > + status = "okay";
> > +};
> > +
> > +/* off-board header */
> > +&uart3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart3>;
> > + status = "okay";
> > +};
> > +
> > +/* USB1 Type-C front panel */
> > +&usb3_0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usb1>;
> > + fsl,over-current-active-low;
> > + status = "okay";
> > +};
> > +
> > +&usb3_phy0 {
> > + status = "okay";
> > +};
> > +
> > +&usb_dwc3_0 {
> > + /* dual role is implemented but not a full featured OTG */
> > + adp-disable;
> > + hnp-disable;
> > + srp-disable;
> > + dr_mode = "otg";
> > + usb-role-switch;
> > + role-switch-default-mode = "peripheral";
> > + status = "okay";
> > +
> > + connector {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbcon1>;
> > + compatible = "gpio-usb-b-connector", "usb-b-connector";
>
> Start the properties from 'compatible'?
>
> Shawn
>
Hi Shawn,
My notes say that pinctrl should come first (if needed) followed by
compatible, reg, other props, and finally status (if needed). Assuming
I'm wrong about that where in the list should pinctrl be and is this
documented anywhere for future reference?
Best regards,
Tim
> > + type = "micro";
> > + label = "Type-C";
> > + id-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
> > + };
> > +};
> > +
> > +/* USB2 - MiniPCIe socket */
> > +&usb3_1 {
> > + fsl,permanently-attached;
> > + fsl,disable-port-power-control;
> > + status = "okay";
> > +};
> > +
> > +&usb3_phy1 {
> > + status = "okay";
> > +};
> > +
> > +&usb_dwc3_1 {
> > + dr_mode = "host";
> > + status = "okay";
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hog>;
> > +
> > + pinctrl_hog: hoggrp {
> > + fsl,pins = <
> > + MX8MP_IOMUXC_SAI1_RXD6__GPIO4_IO08 0x40000146 /* DIO1 */
> > + MX8MP_IOMUXC_SAI1_TXC__GPIO4_IO11 0x40000146 /* DIO0 */
> > + MX8MP_IOMUXC_SAI1_TXD2__GPIO4_IO14 0x40000106 /* PCIE_USBSEL */
> > + MX8MP_IOMUXC_SAI2_TXD0__GPIO4_IO26 0x40000146 /* DIO2 */
> > + MX8MP_IOMUXC_SAI2_TXFS__GPIO4_IO24 0x40000146 /* DIO3 */
> > + MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28 0x40000106 /* PCIE_WDIS# */
> > + >;
> > + };
> > +
> > + pinctrl_accel: accelgrp {
> > + fsl,pins = <
> > + MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21 0x150 /* IRQ */
> > + >;
> > + };
> > +
> > + pinctrl_gpio_leds: gpioledgrp {
> > + fsl,pins = <
> > + MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01 0x6 /* LEDG */
> > + MX8MP_IOMUXC_SAI1_RXD3__GPIO4_IO05 0x6 /* LEDR */
> > + >;
> > + };
> > +
> > + pinctrl_pcie0: pcie0grp {
> > + fsl,pins = <
> > + MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29 0x106
> > + >;
> > + };
> > +
> > + pinctrl_pps: ppsgrp {
> > + fsl,pins = <
> > + MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03 0x146
> > + >;
> > + };
> > +
> > + pinctrl_usb1: usb1grp {
> > + fsl,pins = <
> > + MX8MP_IOMUXC_GPIO1_IO13__USB1_OTG_OC 0x140 /* USB1_FLT# */
> > + >;
> > + };
> > +
> > + pinctrl_usbcon1: usbcon1grp {
> > + fsl,pins = <
> > + MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21 0x140 /* USB1_ID */
> > + >;
> > + };
> > +
> > + pinctrl_spi2: spi2grp {
> > + fsl,pins = <
> > + MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK 0x140
> > + MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI 0x140
> > + MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO 0x140
> > + MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13 0x140
> > + >;
> > + };
> > +
> > + pinctrl_uart1: uart1grp {
> > + fsl,pins = <
> > + MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x140
> > + MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x140
> > + >;
> > + };
> > +
> > + pinctrl_uart3: uart3grp {
> > + fsl,pins = <
> > + MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX 0x140
> > + MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX 0x140
> > + >;
> > + };
> > +};
> > --
> > 2.25.1
> >
Powered by blists - more mailing lists