Message-ID: <SG2PR04MB5543559DECDDF6B075BEAC85A102A@SG2PR04MB5543.apcprd04.prod.outlook.com>
Date:   Mon, 24 Jul 2023 06:03:36 +0000
From:   Delphine_CC_Chiu/WYHQ/Wiwynn <Delphine_CC_Chiu@...ynn.com>
To:     Guenter Roeck <linux@...ck-us.net>
CC:     "patrick@...cx.xyz" <patrick@...cx.xyz>,
        Jean Delvare <jdelvare@...e.com>,
        Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
        "linux-i2c@...r.kernel.org" <linux-i2c@...r.kernel.org>,
        "linux-hwmon@...r.kernel.org" <linux-hwmon@...r.kernel.org>,
        "devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
        "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>
Subject: RE: [PATCH v1 2/2] hwmon: pmbus: Add ltc4286 driver

> -----Original Message-----
> From: Guenter Roeck <groeck7@...il.com> On Behalf Of Guenter Roeck
> Sent: Monday, April 24, 2023 10:14 PM
> To: Delphine_CC_Chiu/WYHQ/Wiwynn <Delphine_CC_Chiu@...ynn.com>
> Cc: patrick@...cx.xyz; Jean Delvare <jdelvare@...e.com>; Rob Herring
> <robh+dt@...nel.org>; Krzysztof Kozlowski
> <krzysztof.kozlowski+dt@...aro.org>; linux-i2c@...r.kernel.org;
> linux-hwmon@...r.kernel.org; devicetree@...r.kernel.org;
> linux-kernel@...r.kernel.org
> Subject: Re: [PATCH v1 2/2] hwmon: pmbus: Add ltc4286 driver
> 
>   Security Reminder: Please be aware that this email is sent by an external
> sender.
> 
> On Mon, Apr 24, 2023 at 06:13:50PM +0800, Delphine CC Chiu wrote:
> > Add support for ltc4286 driver
> 
> The patch does not add support for a driver, it adds support for a chip.
Add a driver to support ltc4286 chip

> 
> >
> > Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@...ynn.com>
> > ---
> >  drivers/hwmon/pmbus/Kconfig   |   9 +++
> >  drivers/hwmon/pmbus/Makefile  |   1 +
> >  drivers/hwmon/pmbus/ltc4286.c | 142
> > ++++++++++++++++++++++++++++++++++
> 
> Documentation is missing.
Documentation is in patch one ([PATCH v1 1/2] dt-bindings: hwmon: Add lltc ltc4286 driver bindings)

> 
> >  3 files changed, 152 insertions(+)
> >  create mode 100644 drivers/hwmon/pmbus/ltc4286.c
> >
> > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> > index 59d9a7430499..1230d910d681 100644
> > --- a/drivers/hwmon/pmbus/Kconfig
> > +++ b/drivers/hwmon/pmbus/Kconfig
> > @@ -218,6 +218,15 @@ config SENSORS_LTC3815
> >         This driver can also be built as a module. If so, the module will
> >         be called ltc3815.
> >
> > +config SENSORS_LTC4286
> > +     bool "Linear Technologies LTC4286"
> 
> Analog Devices ?
We will revise to "Analog Devices LTC4286"

> 
> > +     help
> > +       If you say yes here you get hardware monitoring support for Linear
> > +       Technology LTC4286.
> > +
> > +       This driver can also be built as a module. If so, the module will
> > +       be called ltc4286.
> > +
> >  config SENSORS_MAX15301
> >       tristate "Maxim MAX15301"
> >       help
> > diff --git a/drivers/hwmon/pmbus/Makefile
> > b/drivers/hwmon/pmbus/Makefile index 3ae019916267..540265539580
> 100644
> > --- a/drivers/hwmon/pmbus/Makefile
> > +++ b/drivers/hwmon/pmbus/Makefile
> > @@ -23,6 +23,7 @@ obj-$(CONFIG_SENSORS_LM25066)       +=
> lm25066.o
> >  obj-$(CONFIG_SENSORS_LT7182S)        += lt7182s.o
> >  obj-$(CONFIG_SENSORS_LTC2978)        += ltc2978.o
> >  obj-$(CONFIG_SENSORS_LTC3815)        += ltc3815.o
> > +obj-$(CONFIG_SENSORS_LTC4286)        += ltc4286.o
> >  obj-$(CONFIG_SENSORS_MAX15301)       += max15301.o
> >  obj-$(CONFIG_SENSORS_MAX16064)       += max16064.o
> >  obj-$(CONFIG_SENSORS_MAX16601)       += max16601.o
> > diff --git a/drivers/hwmon/pmbus/ltc4286.c
> > b/drivers/hwmon/pmbus/ltc4286.c new file mode 100644 index
> > 000000000000..474f4ec9107c
> > --- /dev/null
> > +++ b/drivers/hwmon/pmbus/ltc4286.c
> > @@ -0,0 +1,142 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Hardware monitoring driver for LTC4286 Hot-Swap Controller
> > + *
> > + * Copyright (c) 2023 Linear Technology
> 
> Really ?
We will remove the copyright declaration as it was false reference from other drivers
Chip vendor doesn't support this driver, so we implement it for our own use and contribute it as Wiwynn is a system manufacturer, our server products use this chip.

> 
> > + */
> > +
> > +#include <linux/err.h>
> > +#include <linux/i2c.h>
> > +#include <linux/init.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/pmbus.h>
> > +#include "pmbus.h"
> > +
> > +// LTC4286 register
> 
> Please no C++ comments in the code.
We will revise to /* LTC4286 register */

> 
> > +#define LTC4286_MFR_CONFIG1 (0xF2)
> 
> Unnecessary ( )
We will revise to #define LTC4286_MFR_CONFIG1 0xF2

> 
> > +
> > +// LTC4286 configuration
> > +#define VRANGE_SELECT (1 << 1)
> 
> #define<space>DEFINE<tab>value, please. Also, please use BIT() macros where
> appropriate.
We will revise to below.
#define VRANGE_SELECT_BIT	BIT(1)

> > +
> > +#define LTC4286_MFR_ID_SIZE 3
> > +
> > +enum chips { ltc4286, ltc4287 };
> 
> There is no LTC4287 according to information available in public.
> It has not even be announced.
> 
> Besides, the above enum is not really used anywhere and therefore has zero
> value. Maybe the LTC4287 is not yet released. Even then, there is no value
> listing it here because its parameters seem to be identical to LTC4286.
It has been announced on Analog Devices website.
Please refer to this link: https://www.analog.com/en/products/ltc2487.html#product-overview
enum chips { ltc4286 = 0, ltc4287 };
Use in v1 line 118 to list chip index instead of hardcoding

> 
> > +
> > +static struct pmbus_driver_info ltc4286_info = {
> > +     .pages = 1,
> > +     .format[PSC_VOLTAGE_IN] = direct,
> > +     .format[PSC_VOLTAGE_OUT] = direct,
> > +     .format[PSC_CURRENT_OUT] = direct,
> > +     .format[PSC_POWER] = direct,
> > +     .format[PSC_TEMPERATURE] = direct,
> > +     .m[PSC_VOLTAGE_IN] = 32,
> > +     .b[PSC_VOLTAGE_IN] = 0,
> > +     .R[PSC_VOLTAGE_IN] = 1,
> > +     .m[PSC_VOLTAGE_OUT] = 32,
> > +     .b[PSC_VOLTAGE_OUT] = 0,
> > +     .R[PSC_VOLTAGE_OUT] = 1,
> > +     .m[PSC_CURRENT_OUT] = 1024,
> > +     .b[PSC_CURRENT_OUT] = 0,
> > +     .R[PSC_CURRENT_OUT] = 3 - 6,
> 
> This needs explanation.
We will add comments as below
/* Initialize the MBR as default settings which is referred to LTC4286 datasheet(March 22, 2022 version) table 3 page 16 */

> 
> > +     .m[PSC_POWER] = 1,
> > +     .b[PSC_POWER] = 0,
> > +     .R[PSC_POWER] = 4 - 6,
> 
> This needs explanation.
We will add comments as below
/* To support small shunt resistor value */

> 
> > +     .m[PSC_TEMPERATURE] = 1,
> > +     .b[PSC_TEMPERATURE] = 273.15,
> 
> Assigning a float to an int doesn't make much sense.
We will revise to .b[PSC_TEMPERATURE] = 273,
However the value for this MBR is 273.15 in datasheet
We use 273 due to pmbus code limitation

> 
> > +     .R[PSC_TEMPERATURE] = 0,
> > +     .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT |
> PMBUS_HAVE_IOUT |
> > +                PMBUS_HAVE_PIN | PMBUS_HAVE_TEMP,
> 
> The chip does have a number of status registers.
We will add status registers here

> 
> > +};
> > +
> > +static int ltc4286_probe(struct i2c_client *client,
> > +                      const struct i2c_device_id *id) {
> > +     int ret;
> > +     u8 block_buffer[I2C_SMBUS_BLOCK_MAX + 1];
> > +     struct device *dev = &client->dev;
> > +     struct pmbus_driver_info *info;
> > +     u32 rsense;
> > +
> > +     ret = i2c_smbus_read_block_data(client, PMBUS_MFR_ID,
> block_buffer);
> > +     if (ret < 0) {
> > +             dev_err(&client->dev, "failed to read manufacturer
> > + id\n");
> 
> Kind of pointless to declare a local 'dev' variable and not use it.
We will drop it

> 
> > +             return ret;
> > +     }
> > +
> > +     /* Refer to ltc4286 datasheet page 20
> > +      * the default manufacturer id is LTC
> 
> Why "default" ?
We will revise to 
/* 
 * Refer to ltc4286 datasheet page 20
 * the manufacturer id is LTC
 */

> 
> > +      */
> 
> Please use standard multi-line comments.
We will revise to
/* 
 * Refer to ltc4286 datasheet page 20
 * the manufacturer id is LTC
 */

> 
> > +     if (ret != LTC4286_MFR_ID_SIZE ||
> > +         strncmp(block_buffer, "LTC", LTC4286_MFR_ID_SIZE)) {
> > +             dev_err(&client->dev, "unsupported manufacturer id\n");
> > +             return -ENODEV;
> > +     }
> > +
> > +     ret = i2c_smbus_read_block_data(client, PMBUS_MFR_MODEL,
> block_buffer);
> > +     if (ret < 0) {
> > +             dev_err(&client->dev, "failed to read manufacturer
> model\n");
> > +             return ret;
> > +     }
> 
> Why read the model if you don't do anything with it ?
We will add comaprision here.
for (mid = ltc4286_id; mid->name[0]; mid++) {
	if (!strncasecmp(mid->name, block_buffer, strlen(mid->name)))
		break;
}

> 
> > +
> > +     ret = of_property_read_u32(client->dev.of_node,
> "rsense-micro-ohms",
> > +                                &rsense);
> > +     if (ret < 0)
> > +             return ret;
> > +
> > +     if (rsense == 0)
> > +             return -EINVAL;
> > +
> 
> There should be a default for systems not supporting devicetree.
After confirming with vendor, they said there is no default rsesne for this chip
The value for rsense depends on hardware engineer in each manufacturer

> 
> > +     info = &ltc4286_info;
> > +
> > +     /* Default of VRANGE_SELECT = 1 */
> > +     if (device_property_read_bool(dev, "vrange_select_25p6")) {
> > +             /* Setup MFR1 CONFIG register bit 1 VRANGE_SELECT */
> > +             ret = i2c_smbus_read_word_data(client,
> LTC4286_MFR_CONFIG1);
> > +             if (ret < 0) {
> > +                     dev_err(&client->dev,
> > +                             "failed to read manufacturer
> configuration one\n");
> > +                     return ret;
> > +             }
> > +
> > +             ret &= ~VRANGE_SELECT; /* VRANGE_SELECT = 0, 25.6V */
> > +             i2c_smbus_write_word_data(client,
> LTC4286_MFR_CONFIG1,
> > + ret);
> 
> Error check missing.
ret = i2c_smbus_write_word_data(client, LTC4286_MFR_CONFIG1, ret);
if (ret < 0) {
	dev_err(&client->dev, "failed to set vrange\n");
     return ret;
}

> 
> > +
> > +             info->m[PSC_VOLTAGE_IN] = 128;
> > +             info->m[PSC_VOLTAGE_OUT] = 128;
> > +             info->m[PSC_POWER] = 4 * rsense;
> > +     } else {
> > +             info->m[PSC_POWER] = rsense;
> 
> This just takes the current configuration, and assumes it is the default.
> That may not be correct. The chip may have been configured by the BIOS, or
> manually.
The MBR values are based on hardware design, so it must be set in initial stage

> 
> > +     }
> > +
> 
> The code assumes that there is only a single chip in the system, or that the
> configuration of all chips is identical. This is not necessarily correct.
If there are more than one LTC4286 or LTC4287 chips, user can add the configuration for different chips in dts file

> 
> > +     info->m[PSC_CURRENT_OUT] = 1024 * rsense;
> > +
> > +     return pmbus_do_probe(client, info); }
> > +
> > +static const struct i2c_device_id ltc4286_id[] = { { "ltc4286", ltc4286 },
> > +                                                { "ltc4287",
> ltc4287
> > +},
> 
> Even if LTC4287 existed, assigning the ID here ...
So do you recommend us to put this enum (enum chips { ltc4286, ltc4287 };) here?

> 
> > +                                                {} };
> > +MODULE_DEVICE_TABLE(i2c, ltc4286_id);
> > +
> > +static const struct of_device_id ltc4286_of_match[] = {
> > +     { .compatible = "lltc,ltc4286" },
> > +     { .compatible = "lltc,ltc4287" },
> 
> ... but not here defeats having it in the first place.
So do you recommend us to not put this enum (enum chips { ltc4286, ltc4287 };) here?

> 
> > +     {}
> > +};
> 
> MODULE_DEVOCE_TABLE() missing.
In v1 line 120

> 
> > +
> > +/* This is the driver that will be inserted */
> 
> Useless comment
We will drop it.

> 
> > +static struct i2c_driver ltc4286_driver = {
> > +     .driver = {
> > +             .name = "ltc4286",
> > +             .of_match_table = ltc4286_of_match,
> > +     },
> > +     .probe = ltc4286_probe,
> > +     .id_table = ltc4286_id,
> > +};
> > +
> > +module_i2c_driver(ltc4286_driver);
> > +
> > +MODULE_AUTHOR("Delphine CC Chiu
> <Delphine_CC_Chiu@...ynn.com>");
> > +MODULE_DESCRIPTION("PMBUS driver for LTC4286 and compatibles");
> > +MODULE_LICENSE("GPL");
> > --
> > 2.17.1
> >

Powered by blists - more mailing lists