linux-kernel - Re: [PATCH 4/9] arm64: dts: qcom: sa8775p-ride: add pin functions for ethernet1

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <5efc1789-e989-4008-8a7c-235d1e7fa269@lunn.ch>
Date:   Mon, 7 Aug 2023 23:39:32 +0200
From:   Andrew Lunn <andrew@...n.ch>
To:     Andrew Halaney <ahalaney@...hat.com>
Cc:     Bartosz Golaszewski <brgl@...ev.pl>,
        Andy Gross <agross@...nel.org>,
        Bjorn Andersson <andersson@...nel.org>,
        Konrad Dybcio <konrad.dybcio@...aro.org>,
        Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
        Conor Dooley <conor+dt@...nel.org>,
        Alex Elder <elder@...aro.org>,
        Srini Kandagatla <srinivas.kandagatla@...aro.org>,
        linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org, netdev@...r.kernel.org,
        Bartosz Golaszewski <bartosz.golaszewski@...aro.org>
Subject: Re: [PATCH 4/9] arm64: dts: qcom: sa8775p-ride: add pin functions
 for ethernet1

On Mon, Aug 07, 2023 at 04:18:21PM -0500, Andrew Halaney wrote:
> On Mon, Aug 07, 2023 at 09:35:02PM +0200, Bartosz Golaszewski wrote:
> > From: Bartosz Golaszewski <bartosz.golaszewski@...aro.org>
> > 
> > Add the MDC and MDIO pin functions for ethernet1 on sa8775p-ride.
> > 
> > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@...aro.org>
> > ---
> >  arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 16 ++++++++++++++++
> >  1 file changed, 16 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> > index 09ae6e153282..38327aff18b0 100644
> > --- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> > +++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> > @@ -480,6 +480,22 @@ ethernet0_mdio: ethernet0-mdio-pins {
> >  		};
> >  	};
> >  
> > +	ethernet1_default: ethernet1-default-state {
> > +		ethernet1_mdc: ethernet1-mdc-pins {
> > +			pins = "gpio20";
> > +			function = "emac1_mdc";
> > +			drive-strength = <16>;
> > +			bias-pull-up;
> > +		};
> > +
> > +		ethernet1_mdio: ethernet1-mdio-pins {
> > +			pins = "gpio21";
> > +			function = "emac1_mdio";
> > +			drive-strength = <16>;
> > +			bias-pull-up;
> > +		};
> > +	};
> > +
> 
> With the whole "EMAC0 MDIO handles the ethernet phy for EMAC1", this
> doesn't seem to make sense.
> 
> I don't have all the schematics, but these pins are not connected from
> what I see.

I kind of agree. I've seen different ways of describing pinmux. What
i've done for Kirkwood was to put all the common pinmux configurations
into the SoC .dtsi file. The .dts file can then reference it if
needed.

In this case, since the bus is unused, it seems odd to mux it. And
later versions of the board could actually use the pins for something
else, GPIOs etc.

      Andrew